Digital Commons Network^™

Phosphate Post-Treatment Of Cerium-Based Conversion Coatings On Al 2024-T3, Daimon K. Heller

Doctoral Dissertations

"Phosphate post-treatment of cerium-based conversion coatings (CeCCs) on high strength aluminum alloys can significantly improve corrosion resistance. As-deposited CeCCs exhibit corrosion pits and salt tails across the specimen surface after 3 days of exposure, but post-treated CeCCs have withstood 14 days of salt spray exposure without visibly corroding. The morphology, phase, and electrochemical properties of spray deposited CeCCs were affected by post-treatment parameters such as immersion time, solution temperature, and phosphate source. The best performing coatings were post-treated in aqueous orthophosphate solutions for at least 5 min at temperatures of at least 85⁰C. These conditions converted cerium hydroxy/peroxy species in …

Theoretical Modeling And Analysis Of Ammonia Gas Sensing Properties Of Vertically Aligned Multiwalled Carbon Nanotube Resistive Sensors And Enhancing Their Sensitivity, Shripriya Darshini Poduri

University of Kentucky Master's Theses

Vertically aligned Multiwalled Carbon Nanotubes (MWCNTs) were grown in the pores of Anodized Aluminum Oxide (AAO) templates and investigated for resistive sensor applications. High Sensitivity of 23% to low concentration (100 ppm) of ammonia was observed. An equivalent circuit model was developed to understand the current flow path in the resistive sensor. This helped us in achieving high sensitivities through amorphous carbon (a-C) layer thickness tailoring by employing post-growth processing techniques like plasma etching.

A simulation model in MATLAB was developed to calculate the device resistance and the change in the sensitivity as a function of device parameters. The steady …

Study Of Carbon Black-Epoxy Based Fat Tissue Phantom And Its Dielectric Properties., Hatem Mohamed Al-Gabroun

Student Works (2010-2019)

Microwave imaging techniques for medical applications have been reported in the literature for many years. However, the progress in imaging algorithms, numerical techniques, microwave hardware and computational speed has renewed the interest in this field. Breast cancer detection is particularly attractive from a microwave imaging perspective, the major reason referred to the potentially high dielectric contrast between cancerous tissues and normal breast tissues depending on water content. Low water tissues tend to be low permittivity as fat, whilst high water content tissues tend to be high permittivity as cancerous tissues. All of that increased the need for effective phantoms that …

Drug-Eluting Stents For Coronary Artery Disease: A Review, David Martin, Fergal Boyle

Articles

Over the past decade the introduction of drug-eluting stents (DESs) has revolutionised the treatment of coronary artery disease. However, in recent years concern has arisen over the long-term safety and efficacy of DESs due to the occurrence of late adverse clinical events such as stent thrombosis. With this concern in mind, research and development is currently centred on increasing the long-term safety and efficacy of DESs. The aim of this paper is to provide a thorough review of currently approved and promising investigational DESs. With dozens of companies involved in the development of new and innovative anti-restenotic agents, polymeric coatings …

Energy Expenditure Analysis Of Redesigned Mechanical Assists For Medium Girder Bridge, Karthik Kumar

Masters Theses

"U.S. Army bridge crew soldiers perform tough manual material handling (MMH) tasks during the assembly of a Medium Girder Bridge (MGB). The bridge parts are very heavy and are manually lifted from pallets, carried to the construction site and assembled with other bridge parts. An energy expenditure study on the soldiers handling the bridge parts revealed that the energy expenditure rate of the soldiers exceeds the NIOSH prescribed safety limit of 3.5 Kcal/min. This leads to high risk of musculoskeletal disorders. The study deals with modifying the first redesign of mechanical assists for medium girder bridge (MGB) and studying the …

The Properties And Structure Of Tin Phosphate Glasses Modified With Other Oxides, Jong Wook (Austin) Lim

Masters Theses

"The main objective of this research was to evaluate the properties and structures of glasses from the stannous (SnO) phosphate system for possible use in low temperature optical applications. Glasses in the binary xSnO-(100-x)P₂O₅ system (50 ≤ x ≤ 70) were prepared and their thermal and optical properties were evaluated. Differences in glass transition temperatures (T_g) measured here and reported in the literature were explained by differences in the residual water content in the glasses, as determined by infrared spectroscopy. In general, increasing the SnO content of the binary glasses increased the refractive index and the glass transition …

Development Of Embedded Modulated Scatterer Technique: Single- And Dual-Loaded Scatterers, Kristen M. Donnell

Doctoral Dissertations

"Health monitoring of infrastructure is an important ongoing issue. Therefore, it is important that a cost-effective and practical method for evaluating complex composite structures be developed. A promising microwave-based embedded sensor technology is developed based on the Modulated Scatterer Technique (MST). MST is based on illuminating a probe, commonly a dipole antenna loaded with a PIN diode (also referred to as a single-loaded scatterer, or SLS), with an electromagnetic wave. This impinging wave induces a current along the scatterer length, which causes a scattered field to be reradiated. Modulating the PIN diode also modulates the signal scattered by the probe, …

The Use Of Novel Non-Destructive Methods For Quality Control And Performance Evaluation Of Concrete Structures, Sree Nanukuttan, Niall Holmes, Sudarsan Srininvasan, Lulu Basheer, Muhammed Basheer, John Mccarter, Gerry Starrs

Conference papers

Concrete cover provides the first line of defense against the ingress of many deleterious substances into the concrete. Therefore, a measure of its transport properties is vital in assessing its long term performance in a given exposure condition. In new structures the rate of ingress of the deleterious substances could be monitored using array of electrical sensors that are embedded in the cover concrete. For structures that are currently in service, tests can be performed by removing cores from the structure (lab based tests) or by using tests that can be performed on the surface (in situ tests). Results relating …

A Study Of The Effect Of The Position Of An Edge Filter Within A Ratiometric Wavelength Measurement System, Qiang Wu, Pengfei Wang, Yuliya Semenova, Gerald Farrell

Articles

The effect of the position of an edge filter within a ratiometric wavelength measurement system was investigated based on three cases: (1) the reflected fibre Bragg grating (FBG) signal passes through both the reference arm and the edge filter arm, (2) the reflected FBG signal is connected directly to the edge filter arm and does not pass through the reference arm, (3) the edge filter sits in line with the FBG and thus the source power is filtered prior to reaching the FBG. Both numerical simulations and experimental results show that cases 1 and 2 have similar system performance whilst …

Authentication Of Biometric Features Using Texture Coding For Id Cards, Jonathan Blackledge, Eugene Coyle

Conference papers

The use of image based information exchange has grown rapidly over the years in terms of both e-to-e image storage and transmission and in terms of maintaining paper documents in electronic form. Further, with the dramatic improvements in the quality of COTS (Commercial-Off-The-Shelf) printing and scanning devices, the ability to counterfeit electronic and printed documents has become a widespread problem. Consequently, there has been an increasing demand to develop digital watermarking techniques which can be applied to both electronic and printed images (and documents) that can be authenticated, prevent unauthorized copying of their content and, in the case of printed …

The Effects Of Harmonics On Power Quality And Energy Efficiency, Alan Harrison

Other resources

By making our electricity supply more secure, reliable and versatile will mean that we reduce our reliance upon oil, gas and solid fuels, which mostly exist outside of Ireland and the European community. The majority of our fuel is imported and this makes our economy dependent on outside interests and out of our control. Even more importantly as the world’s fossil fuel reserves are running out and electricity demand is ever increasing.

If we make our electricity networks secure and designed to the highest standards we can import and export electrical energy more easily as our demands change, for example …

Pvd And Cvd Coatings For The Metal Forming Industry, Simon Montgomery, David Kennedy, Noel O'Dowd

Conference Papers

Metal forming applications are, by their very nature, taxing on the tools and machines used to achieve a finished component. Material degradation and wear is of critical importance in any such operation as a failing in the tool or machine has the potential to cause health hazards and/or significant monetary losses. The wear of material is due to the contact of two opposing surfaces and their subsequent motion relative to each other. It can take many forms some examples of which are: a two or three body abrasive type, a rolling fatigue type or an adhesion type.

Much research has …

An Investigation Of The Rwpe Prostate Derived Family Of Cell Lines Using Ftir Spectroscopy, M. Baker, Colin Clarke, D. Demoulin, J. Nicolson, Fiona Lyng, Hugh Byrne, C. Hart, M. Brown, N. Clarke, P. Gardner

Articles

Interest in developing robust, quicker and easier diagnostic tests for cancer has lead to an increased use of Fourier transform infrared (FTIR) spectroscopy to meet that need. In this study we present the use of different experimental modes of infrared spectroscopy to investigate the RWPE human prostate epithelial cell line family which are derived from the same source but differ in their mode of transformation and their mode of invasive phenotype. Importantly, analysis of the infrared spectra obtained using different experimental modes of infrared spectroscopy produce similar results. The RWPE family of cell lines can be separated into groups based …

Estimation Of 3d Shape In The Patellofemoral Joint Using Statistical Shape Models And 2d Data, Colm O'Kane

Conference Papers

Disorders of the patellofemoral joint (PFJ) including PF osteoarthritis and PF pain disorder have been estimated to represent 25% of all patients presenting for knee joint treatment. The diagnosis and treatment of these disorders is curtailed by lack of understanding of the mechanical operation of the joint. A crucial aspect to be considered in understanding contact patterns and kinematics of the PFJ is the alignment of the patella in the trochlear groove. Investigation of patellar alignment necessitates accurate knowledge of the 3D articular surfaces of both patella and femur, along with underlying bone geometry. These 3D data are generally obtained …

Motion Of The Multisegmental Foot In Hallux Valgus, Karl Canseco, Leah Rankine, Jason T. Long, Thomas Smedberg, Richard Marks, Gerald F. Harris

Biomedical Engineering Faculty Research and Publications

Hallux valgus is a common condition characterized by lateral deviation of the large toe and medial deviation of the first metatarsal. While some gait analyses of patients with hallux valgus have been performed using plantar pressures, very little is known about the kinematics of gait in this population. The purpose of this study was to evaluate triplanar kinematics in patients with hallux valgus using a multisegmental foot model. Materials and Methods: A 15-camera Vicon Motion Analysis System was used to evaluate the gait of 38 feet in 33 patients with mild to severe hallux valgus. The Milwaukee foot model was …

Lattice Boltzmann Modeling For Shallow Water Equations Using High Performance Computing, Kevin Tubbs

LSU Doctoral Dissertations

The aim of this dissertation project is to extend the standard Lattice Boltzmann method (LBM) for shallow water flows in order to deal with three dimensional flow fields. The shallow water and mass transport equations have wide applications in ocean, coastal, and hydraulic engineering, which can benefit from the advantages of the LBM. The LBM has recently become an attractive numerical method to solve various fluid dynamics phenomena; however, it has not been extensively applied to modeling shallow water flow and mass transport. Only a few works can be found on improving the LBM for mass transport in shallow water …

Point-Of-Care Immunoassay System Using Carbon Nanotube Labels, Adeyabeba Abera

LSU Doctoral Dissertations

The goal of this research was to develop enhanced signal detection mechanisms for immunosensing using carbon nanotubes (CNTs). The utilization of CNT labels for direct electrical measurement was implemented on lateral flow system and microfluidic integrated interdigitated array microelectrodes. These sensing mechanisms in simple and miniaturized system provided higher sensitivity and autonomous flow control for rapid detection aimed at point-of-care diagnostics. Specific functionalization protocols were carried out to chemically modify the surface of the CNTs for uniform dispersion and antibody conjugation in aqueous solution. Surfactant assisted dispersion of the CNTs was studied using PVP and PEG. Covalent conjugation of antibodies …

Antioxidant Nanoparticles As Delivery Systems, Carlos Ernesto Astete R.

LSU Doctoral Dissertations

The goal of the study was to develop antioxidant polymeric nanoparticles as a new delivery system for food and pharmaceutical applications. Natural antioxidants like alpha-tocopherol, vitamin C, and carnosine, are responsible to protect biological systems against free radicals attack. The conjugation of vitamin C-vitamin E (EC) and alpha-tocopherol-carnosine (VECAR) were performed to obtain antioxidant surfactants which were used for polymeric nanoparticle synthesis. The surfactant made of á-tocopherol (vitamin E) and ascorbic acid (vitamin C) of antioxidant properties dubbed as EC was used to make poly(lactic-co-glycolic) acid (PLGA) nanoparticles. Self-assembled EC nanostructures and PLGA-EC nanoparticles were made by nanoprecipitation, and the …

Value-Added Processing Of Rice And Rice By-Products, Rebecca C. Schramm

LSU Doctoral Dissertations

World competition has encouraged United States rice farmers and rice mills to be efficient in farming and production practices. Efforts to augment economic competitiveness include development of new varieties, improvements in milling practices, and identification of uses for rice products and by-products. The research detailed in this dissertation adds to the body of knowledge in milling practices and identification of uses for rice bran. To improve the prediction of milled rice quality at industrial scale, correlations for milling quality among laboratory, pilot, and industrial scale mills were identified for Clearfield 161. Final industrial product whiteness was ten points higher than …

Structural Health Monitoring With Piezoelectric Wafer Active Sensors—Predictive Modeling And Simulation, Victor Giurgiutiu

Faculty Publications

This paper starts a review of the state of the art in structural health monitoring with piezoelectric wafer active sensors and follows with highlighting the limitations of the current approaches which are predominantly experimental. Subsequently, the paper examines the needs for developing a predictive modeling methodology that would allow to perform extensive parameter studies to determine the sensing method’s sensitivity to damage and insensitivity to confounding factors such as environmental changes, vibrations, and structural manufacturing variability. The thesis is made that such a predictive methodology should be multi-scale and multi-domain, thus encompassing the modeling of structure, sensors, electronics, and power …

Structural Health Monitoring With Piezoelectric Wafer Active Sensors--Predictive Modeling And Simulation, Victor Giurgiutiu

Faculty Publications

This paper starts a review of the state of the art in structural health monitoring with piezoelectric wafer active sensors and follows with highlighting the limitations of the current approaches which are predominantly experimental. Subsequently, the paper examines the needs for developing a predictive modeling methodology that would allow to perform extensive parameter studies to determine the sensing method’s sensitivity to damage and insensitivity to confounding factors such as environmental changes, vibrations, and structural manufacturing variability. The thesis is made that such a predictive methodology should be multi-scale and multi-domain, thus encompassing the modeling of structure, sensors, electronics, and power …

Exploration Of The Role Of Serum Factors In Maintaining Bone Mass During Hibernation In Black Bears, Rachel Marie Bradford

Dissertations, Master's Theses and Master's Reports - Open

Disuse osteoporosis is a condition in which reduced mechanical loading (e.g. bed-rest, immobilization, or paralysis) results in unbalanced bone turnover. The American black bear is a unique, naturally occurring model for the prevention of disuse osteoporosis. Bears remain mostly inactive for up to half a year of hibernation annually, yet they do not lose bone mechanical strength or structural properties throughout hibernation. The long-term goal of this study is to determine the biological mechanism through which bears maintain bone during hibernation. This mechanism could pinpoint new signaling pathway targets for the development of drugs for osteoporosis prevention. In this study, …

Building Support For Coud Computing In The Irish Construction Industry, Alan Redmond, Alan V. Hore, Roger West

Conference papers

The construction industry has been traditionally recognised as a fragmented sector associated with a poor level of implementation and penetration of Information Communication Technology (ICT) by Small to Medium Size Enterprises (SMEs). Cloud computing is a collective term that can facilitate the ability to collaborate within a central repository that can act as a base for interoperability between various construction disciplines and their software applications. Cloud computing is a new layer of internet architecture that creates an open opportunity to add better functionality to an increasingly global network. The characteristics of cloud computing, such as, shared infrastructure, on-demand applications, elasticity …

Tapping Environmental History To Recreate America’S Colonial Hydrology, Christopher L. Pastore, Mark B. Green, Daniel J. Bain, Andrea Muñoz-Hernandez, Charles J. Vörösmarty, Jennifer Arrigo, Sara Brandt, Jonathan M. Duncan, Francesca Greco, Hyojin Kim, Sanjiv Kumar, Michael Lally, Anthony J. Parolari, Brian Pellerin, Nira Salant, Adam Schlosser, Kate Zalzal

Civil and Environmental Engineering Faculty Research and Publications

To properly remediate, improve, or predict how hydrological systems behave, it is vital to establish their histories. However, modern-style records, assembled from instrumental data and remote sensing platforms, hardly exist back more than a few decades. As centuries of data is preferable given multidecadal fluxes of both meteorology/climatology and demographics, building such a history requires resources traditionally considered only useful in the social sciences and humanities. In this Feature, Pastore et al. discuss how they have undertaken the synthesis of historical records and modern techniques to understand the hydrology of the Northeastern U.S. from Colonial times to modern day. Such …

Individualized Cognitive Modeling For Close-Loop Task Mitigation, Guangfan Zhang, Roger Xu, Wei Wang, Jiang Li, Tom Schnell, Mike Keller, Thomas E. Pinelli (Ed.)

Electrical & Computer Engineering Faculty Publications

An accurate real-time operator functional state assessment makes it possible to perform task management, minimize risks, and improve mission performance. In this paper, we discuss the development of an individualized operator functional state assessment model that identifies states likely leading to operational errors. To address large individual variations, we use two different approaches to build a model for each individual using its data as well as data from subjects with similar responses. If a subject's response is similar to that of the individual of interest in a specific functional state, all the training data from this subject will be used …

Prostate Cancer Region Prediction Using Maldi Mass Spectra, Ayyappa Vadlamudi, Shao-Hui Chuang, Xiaoyan Sun, Lisa Cazares, Julius Nyalwidhe, Dean Troyer, O. John Semmes, Jiang Li, Frederic D. Mckenzie

Electrical & Computer Engineering Faculty Publications

For the early detection of prostate cancer, the analysis of the Prostate-specific antigen (PSA) in serum is currently the most popular approach. However, previous studies show that 15% of men have prostate cancer even their PSA concentrations are low. MALDI Mass Spectrometry (MS) proves to be a better technology to discover molecular tools for early cancer detection. The molecular tools or peptides are termed as biomarkers. Using MALDI MS data from prostate tissue samples, prostate cancer biomarkers can be identified by searching for molecular or molecular combination that can differentiate cancer tissue regions from normal ones. Cancer tissue regions are …

Residential Energy Monitoring: Missouri S&T Solar Village Development, Christopher David Wright

Masters Theses

"As energy costs are rising, public and private sector groups are searching for improved energy efficiency technology. Research tools for predicting residential energy usage are lagging behind commercial developments. Missouri S&T has a unique and strong opportunity to strengthen its involvement in the development of residential energy research and knowledge. The S&T Solar Village, a collection of homes designed for energy efficiency and renewable energy, is poised to support this research. This thesis develops a design for residential energy evaluation and data collection of the four solar homes in the Village. The energy evaluation system identifies over 300 sensors and …

Incorporating New Technology Into Healthcare: An Analysis Of Performance, Acceptance, And Safety, Anthony Joseph Strawhun

Masters Theses

"Each year, advances in the healthcare industry allows for better patient care and increased ability to save lives. Looking at standardized and common healthcare devices for both inside and outside the hospital environment, this research studied the tradeoffs and human factors that affect operator performance and patient survival. This research studied the impact of human factors and technology in the development and implementation of the automated external defibrillator for out-of-hospital use and the incremental advantages of SMArT infusion pump technology over traditional intravenous infusion pumps for in-hospital care. The study highlights the complex human factors of both products and establishes …

Adaptive User Interface For Vehicle Swarm Control, Paul Robinette

Masters Theses

"An algorithm to automatically generate behaviors for robotic vehicles has been created and tested in a laboratory setting. This system is designed to be applied in situations where a large number of robotic vehicles must be controlled by a single operator. The system learns what behaviors the operator typically issues and offers these behaviors to the operator in future missions. This algorithm uses the symbolic clustering method Gram-ART to generate these behaviors. Gram-ART has been shown to be successful at clustering such standard symbolic problems as the mushroom dataset and the Unix commands dataset. The algorithm was tested by having …

Sensor Data-Based Decision Making, Ahmet Soylemezoglu

Doctoral Dissertations

"Increasing globalization and growing industrial system complexity has amplified the interest in the use of information provided by sensors as a means of improving overall manufacturing system performance and maintainability. However, utilization of sensors can only be effective if the real-time data can be integrated into the necessary business processes, such as production planning, scheduling and execution systems. This integration requires the development of intelligent decision making models that can effectively process the sensor data into information and suggest appropriate actions. To be able to improve the performance of a system, the health of the system also needs to be …