Digital Commons Network^™

An Experimental And Theoretical Investigation Of The Preferred Orientation In Deformed And Recrystallized Hafnium, David S. Gould

Doctoral Dissertations

"The research problem, as presented, therefore became two-fold; first to investigate and determine the feasibility of fabrication of hafnium and secondly to study the deformation characteristics of the material in light of the overall study of hexagonal metals aimed at the development of an overall general theory of plastic deformation. This appeared to envolve a study of the operating deformation systems in hafnium and the theoretical and experimental study of the textures resulting from plastic deformation. These were to be analyzed in comparison with the other hexagonal metals.

It became evident immediately that the research techniques which must be evolved …

A Thermodynamic Study Of The Titanium Sulfides, Reinhard Paul Abendroth

Doctoral Dissertations

"The determination of the thermodynamic properties of chemical compounds is in essence an experimental one. The purpose of this investigation was (1) to make an experimental determination of the thermodynamic properties of the titanium sulfides (2) to determine what sulfide phases are present in the titanium-sulfur system (3) to show the relationships between the various phases present"--The Problem, Statement of the Problem, page 3.

Investigation Of Plastic Deformation In Prestressed Concrete Slabs From Long Time Loading, Joe B. Roberts

Masters Theses

"It is the purpose of this research to investigate the creep in a thin concrete slab under a long-time prestress load with the compressive load being applied to the edge of the slab through a bearing plate of small dimensions.

Seven plain concrete slabs, 3' x 4' x 4", approximately one year old, made of normal cement and approved aggregate were subjected to the following loading conditions: (1) Three slabs loaded at the center of the greater dimension with a prestress load or 20,000 pounds applied over an area of eight square inches, (2) Three slabs loaded symmetrically at six …

Correlation Of Accident Rates And Roadway Factors, John C. Woo

JTRP Technical Reports

No abstract provided.

Indiana's Highway Needs Study : Technical Paper, Donald O. Covault

JTRP Technical Reports

No abstract provided.

Considerations Of Equipment, Methods And Standards Of Accuracy Applicable To Aerial Surveys For Different Purposes : Technical Paper, Robert Douglas Miles

JTRP Technical Reports

No abstract provided.

The Strength Of Bituminous Mixtures And Their Behavior Under Repeated Loads, Part 2, Leonard E. Wood, William Harner Goetz

JTRP Technical Reports

No abstract provided.

Power Augers And Earth Resistivity Units As Supplements To Drilling Machines, D. G. Shurig

JTRP Technical Reports

No abstract provided.

Pumping Of Highway And Airfield Pavements: Technical Paper, Eldon J. Yoder

JTRP Technical Reports

No abstract provided.

Test 606: John Deere 720/730 All-Fuel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere 720/730 All-Fuel TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear. This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated. BELT HORSEPOWER TESTS …

Test 605: John Deere 720/730, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere 720/730 TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear. This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated. BELT HORSEPOWER TESTS TEST …

A Field And Laboratory Examination Of Weathering Effects On Petroleum And Blended Petroleum-Natural Asphalts In Paving Mixtures, Ellis G. Williams

Kentucky Transportation Center Research Report

The relative merits of various asphalts and asphaltic materials have been the subject of considerable controversy almost from the beginning of flexible pavement construction in this country. In this early period petroleum asphalt had not yet entered the picture and controversy centered about naturally occurring products such as Trinidad natural asphalt and impregnated stones. In 1876 Congress directed that comparative service tests be made on a rock asphalt* and a sheet asphalt containing Trinidad natural asphalt. The sheet asphalt was considered the more successful of these and thus Trinidad natural asphalt became firmly established as a paving material in this …

Analysis Of Pavement Riding Quality: A Triaxial Evaluation Of Pavement Roughness, William S. Foy

Kentucky Transportation Center Research Report

For the last twenty-five years considerable research has been directed toward developing reliable equipment for evaluating pavement roughness. Since roughness inhibits passenger riding comfort and safety, as well as inducing vehicle deterioration, the determination of the features that cause roughness would indicate possible improvements in pavement design, materials, construction practices and equipment. For example, certain types of base design might be found to produce smoother surfaces than others; and a construction practice such as a blade-spread leveling course might result in more uniform pavements. Then too, evaluation of pavement roughness would permit relative comparison of pavements as one of several …

Test 604: John Deere 620/630 All-Fuel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere 620/630 All-Fuel TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear. This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated. BELT HORSEPOWER TESTS …

Test 603: Massey-Harris 333 (Gasoline), Nebraska Tractor Test Lab

Nebraska Tractor Tests

This report and any related files are made available to the online through the Lester F. Larsen Tractor Test and Power Museum as resources allow. Established in 1998, this museum is located on the University of Nebraska-Lincoln East Campus. It is and appropriately housed within the walls of the historic 1920 Nebraska Tractor Test Laboratory, where the first tractor test was started on March 31st, 1920. Because the pioneer tests became worldwide standards, this location was designated as a Historic Landmark of Agricultural Engineering by the American Society of Agricultural Engineers in 1980, shortly after testing was moved to a …

Test 602: Massey-Harris 444 Lp, Nebraska Tractor Test Lab

Nebraska Tractor Tests

This report and any related files are made available to the online through the Lester F. Larsen Tractor Test and Power Museum as resources allow. Established in 1998, this museum is located on the University of Nebraska-Lincoln East Campus. It is and appropriately housed within the walls of the historic 1920 Nebraska Tractor Test Laboratory, where the first tractor test was started on March 31st, 1920. Because the pioneer tests became worldwide standards, this location was designated as a Historic Landmark of Agricultural Engineering by the American Society of Agricultural Engineers in 1980, shortly after testing was moved to a …

Test 601: John Deere 420/430 C, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere 420/430 C TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear. This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated. BELT HORSEPOWER TESTS …

Test 600: John Deere 420 S All-Fuel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere 420 S All-Fuel TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear. This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated. BELT HORSEPOWER …

Test 599: John Deere 420/430 W, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere 420/430 W TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear. This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated. BELT HORSEPOWER TESTS …

Test 598: John Deere 620/630, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere 620/630 TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear. This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated. BELT HORSEPOWER TESTS TEST …

Test 597: John Deere 520/530 Gasoline, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere 520/530 Gasoline TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear. This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated. BELT HORSEPOWER TESTS …

Test 596: Ferguson Model 40, Nebraska Tractor Test Lab

Nebraska Tractor Tests

This report and any related files are made available to the online through the Lester F. Larsen Tractor Test and Power Museum as resources allow. Established in 1998, this museum is located on the University of Nebraska-Lincoln East Campus. It is and appropriately housed within the walls of the historic 1920 Nebraska Tractor Test Laboratory, where the first tractor test was started on March 31st, 1920. Because the pioneer tests became worldwide standards, this location was designated as a Historic Landmark of Agricultural Engineering by the American Society of Agricultural Engineers in 1980, shortly after testing was moved to a …

Test 595: Massey-Harris Model 50, Nebraska Tractor Test Lab

Nebraska Tractor Tests

This report and any related files are made available to the online through the Lester F. Larsen Tractor Test and Power Museum as resources allow. Established in 1998, this museum is located on the University of Nebraska-Lincoln East Campus. It is and appropriately housed within the walls of the historic 1920 Nebraska Tractor Test Laboratory, where the first tractor test was started on March 31st, 1920. Because the pioneer tests became worldwide standards, this location was designated as a Historic Landmark of Agricultural Engineering by the American Society of Agricultural Engineers in 1980, shortly after testing was moved to a …

Test 594: John Deere 720/730 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere 720/730 Diesel TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear. This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated. BELT HORSEPOWER TESTS …

Test 593: John Deere 720/730 Lpg, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere 720/730 LPG TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear. This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated. BELT HORSEPOWER TESTS …

Test 592: John Deere 520/530 All-Fuel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere 520/530 All-Fuel TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear. This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated. BELT HORSEPOWER TESTS …

Test 591: John Deere 620/630 Lpg, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere 620/630 LPG TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear. This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated. BELT HORSEPOWER TESTS …

Test 590: John Deere 520/530 Lpg, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere 520/530 LPG TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear. This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated. BELT HORSEPOWER TESTS …

Test 589: International T-6, Nebraska Tractor Test Lab

Nebraska Tractor Tests

This report and any related files are made available to the online through the Lester F. Larsen Tractor Test and Power Museum as resources allow. Established in 1998, this museum is located on the University of Nebraska-Lincoln East Campus. It is and appropriately housed within the walls of the historic 1920 Nebraska Tractor Test Laboratory, where the first tractor test was started on March 31st, 1920. Because the pioneer tests became worldwide standards, this location was designated as a Historic Landmark of Agricultural Engineering by the American Society of Agricultural Engineers in 1980, shortly after testing was moved to a …

Test 587: International Td-6, Nebraska Tractor Test Lab

Nebraska Tractor Tests

This report and any related files are made available to the online through the Lester F. Larsen Tractor Test and Power Museum as resources allow. Established in 1998, this museum is located on the University of Nebraska-Lincoln East Campus. It is and appropriately housed within the walls of the historic 1920 Nebraska Tractor Test Laboratory, where the first tractor test was started on March 31st, 1920. Because the pioneer tests became worldwide standards, this location was designated as a Historic Landmark of Agricultural Engineering by the American Society of Agricultural Engineers in 1980, shortly after testing was moved to a …