Digital Commons Network^™

Collecting Data About Logic Simulation, Roger D. Chamberlain, Mark A. Franklin

All Computer Science and Engineering Research

Design of high performance hardware and software based gate-switch level logic simulators requires knowledge about the logic simulation process itself. Unfortunately, little data is publically available concerning key aspects of this process. An example of this is the lack of published empirical measurements relating to the time distribution of events generated by such simulators. This paper presents a gate-switch level logic simulator lsim which is oriented towards the collection of data about the simulation process. The basic components of lsim are reviewed, and its relevant data gathering facilities are discussed. An example is presented which illustrates the use of lsim …

Summary Report Of Ranking Methodologies, Robert C. Deen

Kentucky Transportation Center Research Report

Participants in the ranking methodologies workshops were a good representation of those various actors (types of agencies or organizations) in the pavement management process. There were nineteen participants, nine of whom were from the United States, six from Canada, and four from European countries. Of the nineteen, eight represented state or provincial governmental units, three represented municipalities, four were employees of national highway agencies, and another four were either consultants or representatives of universities. Unfortunately, however, all participants represented the technical levels involved in pavement ranking. No one was present to provide the viewpoint of the ultimate decision makers -- …

Effect Of Rules And Laws On The Sustained Availability Of Groundwater, Richard C. Peralta, Paul Killian, Keyvan Asghari

Civil and Environmental Engineering Faculty Publications

No abstract provided.

Acuta Enews April 1985, Vol. 14, No. 4

ACUTA Newsletters

In This Issue

Party Line

Pay-As-You-Talk? Fad or Fortune?

Potpourri

Telephone System at The University of Oklahoma

AT&T Private-Line Tariffs Said to Offer Options, Risk

Rivest-Shamir-Adelman Cryptosystem, Edward A. Fetzner

Theses & Honors Papers

Cryptography, the art of writing secret messages, has been practiced for almost 3000 years. Two people have a message to communicate to each other , with a chance of an outside person intercepting the message before it reaches the receiver . Therefore, the message must be put through an encryption scheme to keep the intervening person from finding the true nature of the message . An encryption scheme is coding a message using an enciphering key and then decoding the coded message with a deciphering key .

Flexible Engineering Software: An Integrated Workstation Approach To Finite Element Analysis, Brant Arnold Ross

Theses and Dissertations

One obstacle preventing more engineers from using finite element analysis (FEA) is the difficulty of transferring data between steps in the modeling process. A Fortran computer program, Rosetta.BYU, has been developed to open data paths between finite element preprocessors (mesh generators) and finite element analysis programs, using a custom data structure. It accepts neutral data files, Version 2.0 IGES data files, and Movie.BYU files for input/output. An application of Rosetta is described. A general workstation manager program, Davinci.BYU, is reviewed that provides a support layer between the engineer and the operating system, organizes software and data files, and facilitates on-line …

Unsteady Transonic Flow Over Slender Bodies, Cevdet Aydun

Mechanical & Aerospace Engineering Theses & Dissertations

The unsteady transonic small disturbance equation for an oscillating slender body is obtained from the full potential equation in cylindrical coordinates by means of a perturbation analysis. The time-dependent body-boundary condition is reduced into a simpler form by matching the outer and inner flows. Also, a time-dependent pressure coefficient over the slender body is derived by means of a matching principle. The simplified form of the body-boundary condition is incorporated into the difference equations at the body axis. This application allows use of the cylindrical coordinate system for the problem. By prescribing several different body-boundary conditions, various modes of body …

A Continuous Distillation Operation At The University Of Tennessee At Chattanooga, David H. Cummins

Honors Theses

This paper describes the work done on the design, construction, monitoring, and control of a distillation column. This work was done as a Departmental Honors Project in the School of Engineering at The University of Tennessee at Chattanooga. The column has been completed and the various tests performed with the column have produced satisfactory results. The column parameters are monitored and controlled by automatic controllers with manually adjusted set points. In addition to this, micro-computer based control for the column has been designed, however implementation of this control has not yet been achieved.

Acuta Enews March 1985, Vol. 14, No. 3

ACUTA Newsletters

In This Issue

Party Line

Telecomm: What Hath Been Wrought?

High Hopes and Tough Realities for Centrex

Explicit Equations For The Polarizing Angles Of A High-Reflectance Substrate Coated By A Transparent Thin Film, R. M.A. Azzam

Electrical Engineering Faculty Publications

Simple explicit equations are derived that determine the angles of incidence at which the parallel and perpendicular polarization components of light are extinguished on reflection from a transparent film coating a high-reflectance (metallic) substrate. The polarizing angles obtained from our approximate expressions are in excellent agreement with those determined by iterative numerical solution of the exact nonlinear equations that govern such angles. For the approximation to be valid, the intensity reflectance of the film-substrate interface, evaluated at the critical angle of the film-ambient interface, must exceed 0.5.

The Applicability Of Microcomputers To Local Water Management, Roderick Lee Allen

Dissertations and Theses

Historically, hydrologic models have been available only on mainframe computers and have therefore not been used by local water managers to support daily decisions. The development of the microcomputer presents an opportunity for that to change.

Mathematical models of soil moisture and river routing are selected, developed and tested for use on a microcomputer as an aid to local water management. The models are then integrated with an appropriate data base in a computer program written for a microcomputer. The result is a Decision Support System for local water managers.

In order to evaluate the feasibility of using the Decision …

Antireflecting And Polarizing Transparent Bilayer Coatings On Absorbing Substrates At Oblique Incidence, R. M.A. Azzam, Karim Javily

Electrical Engineering Faculty Publications

The condition of zero reflection of p- and s-polarized light by a transparent bilayer on an absorbing substrate is derived in the form |g_ν(ø,N_i)| ≤ 1, where g_ν is a function of the angle of incidence ø, the refractive indices N_i(i = 0,1,2,3) of the system, and the polarization state ν (= p or s). As an application, the air-Si₃N₄-SiO₂-Si system is considered at two laser wavelengths λ = 6328 and 3250 Å. The thicknesses of the two films of the bilayer and the …

Industrial Earthquake Preparedness In Shizuoka And The Role Of The Prefectural Government, Guna S. Selvaduray

Faculty Publications

The Shizuoka Prefectural Office in Japan plays an important role in promoting earthquake emergency preparedness among its industries. In addition to implementing regulatory requirements and enacting new regulations as necessary, the Prefectural Office also provides significant guidance to industry. This includes making publications available and periodic surveys of the status of industrial emergency preparedness. A pharmaceutical company in the prefecture has developed an impressive earthquake preparedness program and hazard reduction techniques. This program addresses both primary and secondary effects of earthquakes.

Irish H & V News

Building Services Engineering

No abstract provided.

Keeping Up With Technological Change, Karlis V. Kopans

Theses

Advances in technology over the past fifty (50) years have changed virtually everything that touches our lives today to some degree. However, in the last five years or so, these innovations have been combined into products and systems which have visibly begun to change society as we have known it in the past.

Only in recent years, have the affects of technological change or innovation on society begun to be examined. While a fair amount of literature has been published to date on specific areas of technological change, few publications have been produced which provide a general overview of the …

A Cogeneration Industrial Park In An Urban Environment In The Year 2000, Raymond T. Scott

Theses

An investigation into the feasibilty of placing an industrial park in an urban environment in the year 2000 was made. A selected cogeneration facility located within the park would supply electricity and process steam to the industries with minimal transmission costs and environmental effects. A projection was made on the industries that would exhibit growth to the end of this century, and yet be environmentally benign in nature. These industries would be placed within the industrial park. The selection of the cogeneration facility was based upon projections of fuel availability, environmental factors and available technologies. Socio-economic factors and the effects …

Simulation Of The Manufacturing System : A General Discussion, Di-Cheing Chien

Theses

This thesis treats the problem of multi-variable sensitivity analysis in a production system which may be used in investigating a variety of characteristics of a flow production system which involve idle time, cost, production rate, ect. are the subjects of the analysis.

The analysis procedure follows the rule of INPUT/OUTPUT through a production process. A simple system model using elements such as : raw material, transfer tool, labor, machine and energy/ or electrical power, is used to lead into the construction of dependent-variable system. A utilization is made of industrial robots as well as humans in loading and unloading machines …

Mode Of Communication And The "Risky Shift" : A Controlled Experiment With Computerized Conferencing And Anonymity In A Large Corporation, Computerized Conferencing & Communications Center, Starr Roxanne Hiltz, Murray Turoff, Kenneth Johnson

Computerized Conferencing and Communications Center Reports

Peer groups of five managers in a large company with a well developed corporate culture engaged in choice dilemma tasks using three modes of communication: face-to-face, synchronous computerized conferences with regular names, and synchronous computerized conferences with assigned pen names. This is the final technical report on the experiment, including documentation of all procedures, and reports of the tests of all hypotheses, including those which were not supported.

Choice behavior varied by problem and mode of communication. On a problem related to a major decision on the future of the company, conservative choices and conservative shifts dominated. On two choice …

Acuta Enews January 1985, Vol. 14, No. 1

ACUTA Newsletters

In This Issue

Yale University

Party Line

The Intelligent Campus

Centrex/ Essx Service

Potpourri

Santa Clara Magazine, Volume 27 Number 3, Winter 1985, Santa Clara University

Santa Clara Magazine

2 - WHEN ARE LEADERS AT THEIR BEST? By James M. Kouzes and Barry Z. Posner. There is a revolution in leadership style taking place in corporate America. This deals with how ordinary people get extraordinary things done in organizations.

7 - A MEDITATION IN ST. IVES By William J. Rewak, S.J. Some reflections on the essence of work taken from Father Rewak's travel diary during a trip to England last summer.

10 - TAKING LAUGHTER SERIOUSLY By John Morreall. A philosophy professor shows how important humor is to human life and how understanding our laughter can help us understand …

Study Of Mo, Au, And Ni Implanted Molybdenum Laser Mirrors By Spectroscopic Ellipsometry, Paul G. Snyder, George H. Bu-Abbud, Jae Oh, John A. Woollam, David Poker, D. E. Aspnes, David Ingram, Peter Pronko

Department of Electrical and Computer Engineering: Faculty Publications

The implantation of 150 kev molybdenum ions into polished molybdenum laser mirrors is found to increase the complex dielectric constant in the visible spectrum. Analysis using the Bruggeman effective medium approximation demonstrates that the increase is due to surface smoothing and that the surface is made nearly atomically smooth by a fluence of 5 x 10¹⁵ /cm². Implantation of Au at 1Mev caused considerable microscopic roughening, as well as a change in the bulk optical properties. 3 MeV Ni ion implantation caused only a slight surface roughening. A thin dielectric film (probably a hydrocarbon) is found to …

Fiber Optic Fluid Level Sensor, Navid Ghandeharioun

Retrospective Theses and Dissertations

A fiber optic fluid level sensor based on light transmission attenuation due to bending losses is designed, built and tested.

Fibers formed with reverse curvatures of decreasing radii will induce and increasing amount of lower order mode light loss to the cladding as the light propagates along the step index multimode fiber. The sensor is arranged in the fluid in a vertical position such that the light travels along the fiber from the bottom or low fluid point to the top or full point. As the fluid covers increasing lengths of the exposed fiber, it strips even more power from …

Evaluation Of A Binary Spatial Light Modulator Correlator Using Time-Domain Polarity Coincidence Correlation Theory, Thomas J. Posluszny

Retrospective Theses and Dissertations

Time-domain Polarity Coincidence Correlators (PCC) have been studied for the possible extension of these theories to the spatial-domain in the context of an optical PCC. The existing body of knowledge has been found to be inadequate for direct application to the spatial-domain. However, by remodeling the type of clipper or hardlimiter used in the development of the existing theory from a signum (bipolar) clipper to a binary (unipolar) clipper, a new expression for the output signal-to-noise ratio of an optical PCC is developed. This modification is necessary to account for the unipolar nature of light intensity. Both the existing time-domain …

Multiplan Models For Construction, Edson. Jackson

Retrospective Theses and Dissertations

As computer hardware becomes smaller and increasingly less expensive, more contractors can now use computers to do a number of construction computations which were formally done on hand calculators. The advent of user-oriented software packages has had a significant impact on the traditional data processing procedures of the construction industry. Among the software packages that are available for a large number of computer systems are electronic spreadsheets. Electronic spreadsheets packages, such as Multiplan, are widely used where the display of information can best be depicted in an array of rows and columns. It is frequently useful in situations in which …

An Approach To Noise Estimation And Elimination In Communication Systems, Jerome J. Viviano

Retrospective Theses and Dissertations

This paper is a description of the analysis and testing of a method to estimate noise mixed in with a desired signal and to then subtract out the estimated noise. The paper documents the situation in which noise becomes a problem, the method of noise elimination, the mathematics used to analyze the noise eliminator, a digital/analog hybrid simulation of a system utilizing the techniques described, and comparative results between expected performance and actual system performance. Also described is the practicality of the system, the limitations of the system and its unique capabilities. Since the system is a totally new concept, …

Golden Opportunities For White Collar Productivity Improvements In Quality Assurance, Jane M. Algee

Retrospective Theses and Dissertations

The efficient processing of defective or nonconforming hardware and paperwork is important to both defense contractors and the government. Management's concern of excessive costs in this area initiated an investigation into the actual activities, personnel, and computer systems involved in such processing. Applicable military specifications and an assortment of corporate and divisional procedures were reviewed to obtain baseline data. Additional information was sought through personal interviews and visits to the manufacturing areas. The activity flow was documented in block diagrams and time estimates and labor requirements were applied. The detailed labor estimates were input to a LOTUS123 spreadsheet and used …

Optimization Analysis For Alignment Criteria And Installation Of Gravity Flow Underground Pipe, Eugene N. Balter

Retrospective Theses and Dissertations

In 1982 the Business Roundtable prepared several reports which investigated various aspects of construction which posed significant research opportunities. Their findings placed piping construction in the group of activities categorized as having "highest potential" for improvements based on inefficiency, or construction difficulty and proportionate costs. It was estimated that over $1 billion could be saved annually if the difficulty in the piping industry was improved to only average of other areas. Further investigation into the piping area showed that the alignment process took 20% of the cycle time for installation and ranked either first or second as compared to other …

An I/O Controller Design For A Mainframe Computer In A Military Training Device, Robert E. Cara

Retrospective Theses and Dissertations

The design of an I/O Controller capable of processing data in real time in a tactical training simulator is presented. The controller consists of two microprocessor systems that communicate with peripherals by means of programmed I/O, and with the host computer by Direct Memory Access (DMA) and a serial RS232 link. This thesis addresses both the hardware and software aspects of the controller design.

Application Software Of The Future-Filter Design With Gem, Alan D. George

Retrospective Theses and Dissertations

As the use of computer in engineering design as well as other areas increase, it becomes more imperative that the application software used be as simple, convenient, and powerful as possible. The engineer is not interested in the internal workings of the computer or its operating system. It is the design itself that takes precedence. The filter design package developed for this project, known as FILTER, is such an application. With FILTER, coupled with the Digital Research Graphics Environment Manager, the engineer is led through the analog and digital filter design phase on a personal computer with carefully designed interactive …

Radar: Theory And Insight, Terry A. Dougherty

Retrospective Theses and Dissertations

Radar principles and design considerations are reviewed, using both analytical and heuristic methods. Emphasis is placed on achieving physical insight while maintaining technical rigor. Waveform properties and signal detectability maximization through matched filtering is discussed in detail. The Moving Target Indicator radar system is presented as an illustration of digital signal processing technology applied to modern radar systems.