Digital Commons Network^™

Electrorheological Characters Of Polyaniline Suspensions, Guangyao Su, Deshu Gao, Changqing Zhang

Journal of Electrochemistry

Polyaniline (PAn) as the dispersive particles and insulating oil as the dispersive medium, the electrorheological fluid (ERF) is constituted. Relations between the factors of electric field strength (E), temperature (T) and the static yield stress (τ_S), current density (i) of ERF are investigated. The results show that the changes of τ_S and i with electric field intensity have emerged in the exponential relation, i.e, τ_S∝E^0.7, i∝E^2.18. Otherwise, when exert a constant voltage on ERF, owing to the polarization, the absorption of medium of ERF have taken place. Therefore, the attenuation rate …

Investigation On Electro Reduction Behaviour Of Copper Anodic Products In Concentrated Naoh Solutions Ⅱ. Electro Reduction Of Cu(Ⅱ) Products, Jianbo He, Hanhe Chen, Jianxin Lin

Journal of Electrochemistry

Potentiostatic oxidation potentiodynamic or galvanostatic reduction methods have been used to study the cathodic reduction behaviour of various products anodically formed on the second stage of copper oxidation in concentrated NaOH solutions. Seven cathodic current peaks and the corresponding cathodic potential plateaus are observed on the potentiodynamic E/i curves and the galvanostatic E/t curves, respectively. In the negative potential scan, there are three couples of voltammetric peaks which have been attributed to the formation and reduction of CuO, Cu(OH)₂ and Cu(Ⅱ) ion, respectively. The complicated mechanism for the electro formation of the three Cu(Ⅱ) species are discussed.

Studies On The Failure Modes Of Stationary Vrla Batteries, Yibo Tong, Xiangming Qiu

Journal of Electrochemistry

In order to improve the reliability and the quality of stationary valve-regulated lead-acid (VRLA) batteries, the failure modes of the stationary VRLA batteries which caused by the water loss and the thermal runaway are studied. The water loss may be solved by increasing the Oxygen-recombination efficiency, choosing the suitable grid material and the additives of megative paste, decreasing the corrosion of the positive plates. The thermal runaway may be solved by decreasing the inner ohmic resistance of VRLA batteries, improving the outside condition of batteries such as putting into the absorbing-heat material between the abtteries etc..

Preparation Of Pbo2/Ti Plate Electrode, Zhigang Shao, Baolian Yi, Xinge Zhang, Enjun Zhang

Journal of Electrochemistry

The perchlorate was made up of a lead dioxide plate elcetrode and an oxygen cathode. By measuring the flow capacity of cell gas in the cell, and by means of CV, SEM, XRD, the performances of the lead dioxide plate electrodes are evaluated. The influence of changes in the concentrations of electroplating solutions (F, HNO₃, Bi³⁺, Ni²⁺, Fe³⁺ and surface active agent) is investigated. The results show that the concentrations of Fe³⁺ in the solutions must be lower 0.01 g/L, and the concentrations of HNO₃ in the solutions are about 20 …

Surface Modifications Of Carbon Materials Used As Anode Of Lithium Ion Battery Ⅲ. Improvement Of Artificially Imposed Solid Electrolyte Film On Cell Performance, Shuhua Ma, Xiabin Jing, Fosong Wang

Journal of Electrochemistry

The improving effect of solid electrolyte film artificially imposed on carbon electrode was investigated. The result showed that both the charge/discharge capacity and first charge/discharge efficiency, to a certain extent, were enhanced, and the result also suggested the effectiveness of the substitution of the artificially imposed solid electrolyte film for the inherent passivating film which was formed on the surface of the carbon electrode while inserted in the electrolyte during charging or discharging. The Scanning Electron Microscope result displayed the compact and well-defined morphology of the artificially imposed crystalline film.

39th Rocky Mountain Conference On Analytical Chemistry

Rocky Mountain Conference on Magnetic Resonance

Preliminary program and registration information for the 39th annual meeting of the Rocky Mountain Conference on Analytical Chemistry, co-sponsored by the Colorado Section of the American Chemical Society and the Rocky Mountain Section of the Society for Applied Spectroscopy. Held in Denver, Colorado, August 3-7, 1997.

A Study Of The Volatile Matter Of Coal As A Function Of The Heating Rate, Enrique Santos

Masters Theses & Specialist Projects

A study of volatile matter yields as a function of the heating rate was conducted. A suite of 21 coal and coke samples varying in rank from anthracitic to lignitic and heating rates from 10°C/min to about 450°C/min were used in the study. Heating rates up to 60°C per minute, which are typically used in ASTM Test Method 5142 (instrumental Proximate Analysis), were achieved in a macro thermogravimetric analysis (TGA) system. Heating rates of 50-200°C/min were obtained in a micro TGA system. All measurements were made in a nitrogen atmosphere. The results of the study illustrate the dependance of the …

Effects Of Tunneling Electrons And Local Field On Nanometer Region Solid / Liquid Interfacial Reactions ——Potential Controlled Stm Induced Nanoscale Modification Of H Terminated Si(111) Surfaces, Zhaoxiong Xie, Xiongwei Cai, Caihui Shi, Bingwei Mao, Zhaowu Tian

Journal of Electrochemistry

H-terminated n-Si(111) surface was found to be etched in 0.5% HF solution in nanometer scale while scanning the STM tip when the substrate potential was somehow lower than the open circuit potential at tunneling condition of V_b=+1.0 V (tip positive), I_t=1 nA. Much more stable Si surface was achievable at potentials much more negative than the open circuit potential (such as 500 mV negative to OCP) under the same tunneling condition. Furthermore, the etching rete at less negative potential was found to be somehow related to the tunneling current. These results indicate that the STM induced …

Studies Of Electrocatalytic Properties Of Electrode Of Dispersed Pt On Gc Support In Ethylene Glycol Oxidation, Shengpei Chen, Shigang Sun, Zhiyou Zhou, Shuanjing Hong

Journal of Electrochemistry

The structures and properties of electrocatalyst of dispersed Plutinum (Pt) on glassy carbon (GC) support under different conditions were studied using cyclic voltammetry, potential step technique, X-ray diffraction (XRD) and scanning Electron microscopy (SEM). The results indicated that after having been treated in high temperature,the dispersed Pt on GC support was recrystallised with preferented orientation, and the grain of Pt microcrystal become large and regular. It was illustrated that the dispersed Pt on GC support after high temperature treatment exhibited better stability and high activity for ethylene glycol oxidation.

Polymer Electrolyte Fuel Cell Powered Vehicles, Naichao Li, Baolian Yi

Journal of Electrochemistry

The background, status and commercialization prospect of polymer electrolyte fuel cell vehicles are surveyed in this paper. The technology of this cell and system used in vehicles is discussed.

Electrochemical Behavior Of Superoxide Dismutase On Gold Minigrid With Thin Layer Cell, Xiaqin Wu, Qian Liu, Bin Xu, Xiaoyun Men, Zongrang Zhang

Journal of Electrochemistry

The electrochemical behavior of superoxide dismutase (Cu, Zn-SOD) was investigated on gold wire electrode and gold minigrid with thin layer cell by cyclic voltammetry. A quasi reversible redox wave of SOD has obtained on gold minigrid thin layer electrode, but only oxidation peak has observed on gold wire electrode. The electrochemical reaction parameters, such as the formal potential E^0′, diffusion coefficient D and standard rate constant k^0′ were estimated.

Electrodeposition Of Amorphous Fe-Cr Alloy Coating, Danhong Cheng, Weiyi Xu, Yiqin Qin, Liqun Hua, Zhongyan Zhang

Journal of Electrochemistry

The amorphous Fe-Cr alloy coatings were obtained by controlling the composition of bath operation conditions. It was found that the pH value, the current density and the content of chromium in Fe-Cr alloy coatings effect the amorphous structure of the coatings. The result of anodic polarization shows that the corrosion resistance of the amorphous coatings in acidic media is higher than the corrosion resistance of the crystal ones.

An Analysis On The Microstructure Of Electrodeposited Zro2-Ni Functionally Graded Materials, Chengjun Quan, Xinghua Xiang, Jingchuan Zhu, Zhongda Yin

Journal of Electrochemistry

The electrodeposited ZrO₂-Ni functionally graded coating was fabricated by controlling the ZrO₂ concentration in the bath, and the microstructure was analyzed by X-Ray Diffraction (XRD) and Electron Probe Microanalysis (EPMA). The results show that the functionally graded coating has excellent compositional gradient distribution from the substrate to the surface. The content of ZrO₂ is up to 14.4 vol% in the surface layer and the coating consists of the t-ZrO₂, m-ZrO₂ and Ni phases. Owing to the ZrO₂ particles pressed by Ni atoms during electrodepositing, t→m transformation has occurred.

Studies On Electrodeposition Of Rare Earth Metals And Their Alloys In Molten Salts, Qiqin Yang

Journal of Electrochemistry

The cyclic voltammetry, convolution voltammetry, potentiostatic electrolysis and open circuit potential time curve after electrolysis, current time curve at potential step, potential time curve at current step, X-ray diffraction, EDAX, electron probe microanalysis were used to investigate the electrode processes of the reduction of rare earth ions on inert electrodes and alloying electrodes in molten chlorides and fluorides. The free energies of formation for the intermetallic compounds, the diffusion coefficients of rare earth ions in the melt, the diffusion coefficients of rare earth atoms in the alloy phases were determined. The alloys of rare earth with iron, cobalt, nickel, copper, …

Surface Modification Of Molten Carbonate Fuel Cell Anode, Baizeng Fang, Xinyu Liu, Xindong Wang, Shuzhen Duan

Journal of Electrochemistry

In this study, the anode material of molten carbonate fuel cell was modified by the deposition of niobium on nickel surface. The results of polarization experiments reveal that the corrosion resistant properties as well as electrocatalytic activity have been improved greatly.

Study Of Electrodepositing Bright Tin Cobalt Zinc Alloy From Weak Acid Solution, Zhengzhong Zuo, Runxiang Hou, Shaochun Xia

Journal of Electrochemistry

A new process of electrodeposting bright Tin Cobalt Zinc alloy from weak acid solution is proposed in this paper. The solution compositions and operating conditions are Na₃C₆H₅O₇·2H₂O 100～150, Na₂EDTA·2H₂O 20～30, SnCl₂·2H₂O 15～20, CoSO₄·72H₂O 25～35, ZnCl₂ 15～20 g·L^-1; stabilizer WDZ-160～100, brightener WDZ-215～20 mL·L^-1; pH=4～6, D_K=0.5～5.0 A·dm^-2, T=5～35 ℃. A bright Sn-Co-Zn deposit having Co about 0.5～3.5% and Zn about 1～10% is produced. The effects of bath compositions on Co or …

Electroluminescence Of Photoelectrochemically Etched N+-Si, Guozheng Li, Chengqian Zhang, Xiumei Yang

Journal of Electrochemistry

Porous silicon with micrometer size pores, which is made on n⁺-Si by photoelectrochemically etched, has electroluminescent property. Each monochromic intensity and wavelength range of luminescent spectra depend on polarized potential. The intersity and the stability of cathodic electroluminescence is high than those of anodic one. Voltammetric behavior before quenching indicated that the electrochemical reactions of some surface species are involved in except the reduction of S₂O₈^2-, which leads to radiative recombination. The energy band diagram based on n⁺-Si(E_g=1.1 eV)/PS(E_g=1.8 eV) junction is proposed.

Effects Of Curvature On The Electrochemical Behaviors Of Tubular Electrode, Yirong Wu, Zhenghao Wang

Journal of Electrochemistry

The convective diffusion equation of tubular electrode was solved with the implicit finite difference numerical method. Comparing with the electrochemical behaviors of channel electrode, the behaviors of tubular electrode were analysised. The effects of curvature on the electrochemical behaviors of tubular electrode and the limit of applying Levich approximation to tubular electrode were discussed.

Mechanism And Texture Of Ni-Mo Alloy Electrodeposition, Ling Huang, Shukai Xu, Jaoning Tang, Fangzu Yang, Shaomin Zhou

Journal of Electrochemistry

Ni-Mo alloy deposits with (111) preferred orientation was obtained in a solution of 0.22 mol/L NiSO₄·6H₂O, 0.06 mol/L Na₂MoO₄·2H₂O and 0.3 mol/L Na₃C₆H₅O₇·2H₂O in temperature from 25℃ to 50℃, and current densities ranged from 10 mA·cm^-2 to 30 mA·cm^-2. The electrodeposition of Ni-Mo alloy was studied by cylic voltammetry and potential step experiment. It was shown that Ni-Mo alloy is formed by mechanism involving progressive nucleation followed by three dimensional growth of the metal centres. The complex …

Study On The Preparation, Properties And Applications Of The Polymer/Graphite Composite Electrode, Guohua Chen, Jinrui Xu

Journal of Electrochemistry

The graphite AS composite electrodes, which show high electric conductivity, high mechanical strength and operationl stability, were prepared by filling and extruding the AS copolymer with graphite powder. It exhibited a substantial hydrogen overvoltage and small residual current in different electrolytes, as compared with glassy carbon electrode. The electrode was applied to the determination of traces of Pb²⁺ in mineral water, Ag⁺ in waste water and In³⁺, Cu²⁺, Pb²⁺, Cd²⁺ in zinc ore, and showed high stability, reproducibility and selectivity. Owing to the existence of abundant polar functioal groups on the …

Laser-Initiated Decomposition Products Of Indocyanine Green (Icg) And Carbon Black Sensitized Biological Tissues, John M. Kokosa, Andrzej Przyjazny, Kenneth Eugene Bartels, Massoud Motamedi, Donald J. Hayes, David B. Wallace, Christopher J. Frederickson

Chemistry & Biochemistry Publications

Organic dyes have found increasing use a s sensitizers in laser surgical procedures, due to their high optical absorbances. Little is known, however, about the nature of the degradation products formed when these dyes are irradiated with a laser. Previous work in our laboratories has shown that irradiation of polymeric and biological tissues with CO2 and Nd:YAG lasers produces a host of volatile and semivolatile by-products, some of which are known to be potential carcinogens. This work focuses on the identification of the chemical by-products formed by diode laser and Nd:YAG laser irradiation of indocyanine green (ICG) and carbon black …

Development Of Methods For The Determination Of Major And Minor Elements And Hydrocarbon Residues In Solid Combustion Products, Xiaoliu Chi

Masters Theses & Specialist Projects

Methods for the determination of inorganic constituents in coal fly ash by glow discharge spectrometry (GDS) and for the extraction of the organic compounds from coal and ash by supercritical fluid extraction (SFE) at temperatures below 150°C are reviewed. The inorganic elements studied included Al, Ca, C, Cu, Fe, Mg, Mn, P, S, Si and Ti. The organic compounds were measured by weight loss of the sample. The goal of this research was to find easier and faster ways to measure the concentration of inorganic elements in coal ash and to measure extractability of the coal itself, to make coal …

A Study Of Combustion Profiles Of Co-Fired Coal/Biomass/Limestone Samples In A Fluidized Bed Combustor, Beverly Campbell

Masters Theses & Specialist Projects

Concerns over declining landfill space and a renewed interest in waste-toenergy technologies have increased the possibilities of co-firing different types of fuels in atmospheric fluidized bed combustion systems. The laboratory sized atmospheric fluidized bed combustor (AFBC) at Western Kentucky University was designed to serve as a highly flexible research and development facility to gain operating experience, evaluate combustion performance, and estimate the effect of flue gas emissions on the atmosphere. The operating conditions for the AFBC system are similar to those used at the TVA 160-MW AFBC Pilot Plant located near Paducah, Kentucky. AFBC systems are ideal for co-firing because …

In Situ Observations Of Air Traffic Emission Signatures In The North Atlantic Flight Corridor, Hans Schlager, Paul Konopka, P. Schulte, U. Schumann, H. Ziereis, F. Arnold, M. Klemm, Donald E. Hagen, Philip D. Whitefield, J. Ovarlez

Physics Faculty Research & Creative Works

Focussed aircraft measurements have been carried out over the eastern North Atlantic to search for signals of air traffic emissions in the flight corridor region. Observations include NO, NO₂, HNO₃, SO₂, O₃, H₂O, total condensation nuclei (CN), and meteorological parameters. A flight pattern with constant-altitude north-south legs across the major North Atlantic air traffic tracks was flown. Signatures of air traffic emissions were clearly detected for NO_x, SO₂, and CN with peak concentrations of 2 ppbv, 0.25 ppbv, and 500 cm^-3, respectively, exceeding background …

Synthesis And Characterization Of Modified Silica Gel As An Intermediate In The Generation Of Gaseous Standard Mixtures, M. Prokopowicz, K. Lewandowska, A. Skwierawska, Andrzej Przyjazny, Jan F. Biernat, J. Namiesnik

Chemistry & Biochemistry Publications

A possibility of extending analytical applications of chemically modified silica gels is described. This involves their utilization for the generation of gaseous standard mixtures consisting of methyl chloride as the analyte and nitrogen as a carrier gas to be used for the calibration of the GC-FID system. N-methylmorpholine was chemically bonded to the propylsilylated surface of silica gel forming chloride of an appropriate immobilized compound which, under certain conditions, undergoes thermal decomposition yielding a single, volatile component (methyl chloride). Such a method of generating specific amounts of a standard substance can be used both for a single point calibration and …

Thermal Studies Of Complex Formations Of First Row Transition Metals With Phenolic Compounds In Aqueous Solution, Nabil Adnan Amro

Masters Theses

The coordination chemistry of protocatechuic acid and catechols with the first row of transition metals was studied as a model for the more complicated natural humic substance.

The reaction between Mn²⁺, Fe³⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺ and the phenols, catechol and protocatechuic acid in aqueous solution was studied by the spectrophotometric method. The composition of the complexes formed was determined by continuous variation, iso-molar series and molar ratio methods. The presence of complexes with metal:ligand ratio of 1:1, 1:2 and 1:3 was established in the pH range 3 to …

Electrochemical Synthesis And Characterization Of Ba-Pb-O And Bi-Pb-O Oxides, Min Xie, Liangzhong Zhao, Cuiying Xu, Jinbiao Zhang

Journal of Electrochemistry

Pb-based oxides Ba-Pb-O and Bi-Pb-O were synthesized from aqueous solutions by using electrochemical method. The resulting Ba-Pb-O and Bi-Pb-O were characterized using XPS, EDX and XRD. The results show that perovskite BaPb_0.9O₃ can be electrodeposited on the anode only from strong alkaline solution. In acid aqueous solution, conducting BiPb₂O_z oxide is fromed on the anode. In these oxides the nominal valence of lead is +4.

Electrochemical Studies Of Spinel Limn2O4 Rechargeable Lithium Battery, Li Feng, Yuqin Chang, Lie Wu, Hong Li, Yibin San, Tianhong Lu

Journal of Electrochemistry

The spinel Li intercalation compound LiMn₂O₄ was prepared and studied using ac impedance and cyclic voltammogram techniques. It was first discussed that the impedance behaviors of LiMn₂O₄ electrode varied as lithium ion was intercalated in or out the electrode with the help of fractal theory. The Li reversible behaviors in LiMn₂O₄ electrode were shown by the cyclic voltammogram results.

Problems Of The Study Of Anodic Films On Pb In Sulfuric Acid Solution (Ⅲ), Houtian Liu, Qunzhou Wang, Weifang Zhou, Wenbin Cai

Journal of Electrochemistry

The interstitial liquid among the particles in anodic Pb(Ⅱ) films could be the major passage for ion transportation. This is discussed with the mechanism of the cathodic reduction of anodic PbSO₄ film and the effect of Sb on the growth of anodic Pb(Ⅱ) oxides film.

Study On The Hydrophilicity Of Nafion Membrane Surface, Yanbing Zu, Chuansin Cha

Journal of Electrochemistry

Due to its high chemical stability and ion selective permeability, Nafion membrane has been applied in many electrochemical systems. The surface hydrophilicity is one of the main factors affecting its performance. In this paper, the bound bubble method is introduced as a suitable way to measure the contact angles between Nafion membrane and various aqueous solutions. During the measurement, Nafion membrane is saturated with given electrolyt solution. The hysteresis of the contact angles observed in the measurement is attributed to the co existance of hydrophobic and hydrophilic domains at the membrane surface. The effect of the solution surface tension on …