Digital Commons Network^™

Prediction Of Extruder Performance For Thermoplastic Materials, Aldo Bergonzoni

Theses

The object of this thesis was to predict the output of an extruder, for thermoplastic materials, by using simplified equations relating output to screw speed and screw geometry.

Three different extruders were used for this purpose and several addition-type polymers were studied. These materials included: stabilized and unstabilized polypropylene, low-density and high-density polyethylene, general-purpose polystyrene and rubber-modified poly-styrene.

The results obtained show that, by using relatively low screw speeds (up to 140 r.p.m.), shallow screw channels and back pressures at the die up to 2000 psig., a theoretical output can be calculated with a maximum deviation from the experimental data …

The Electrical And Optical Properties Of Organic Semiconductors. Part 1 : Preliminary Survey And Purification Techniques, Bohdan Robert Czorny

Theses

The purpose of this work was to investigate the field of organic semiconductors and in particular to develop the means for preparing these materials in suitable condition for measurement and study of semiconducting properties. The first aspects of this project concerned with a preliminary survey of the field and techniques of ultra purification are covered in this work.

Anthracene was selected for investigation because it is the organic semiconductor most commonly studied by other investigators, and considerable published information exists for corroboration.

The preliminary survey elucidated the most promising methods of purification, which were chemical synthesis, sublimation, recrystallization from solvents …

The Corrosiveness Of Phenols, Edgar George Kaup

Theses

The effects of oxidizing agents, heat, light, and metallic catalysts on coloration in phenols is discussed, using data collected from the literature. The oxidation reaction is concluded to be the con-trolling factor in coloration. Corrosion data from laboratory experiments, field tests, and operating plants is presented for metals and non-metals in concentrated phenolic systems.

Synthesis Of Trimethyl Borate By Ester Interchange, Hugh Murphy

Theses

Trimethyl borate was prepared by transesterification of a high—boiling methyl ester with a high—boiling trialkyl borate using a metal alcholate catalyst. Interchange occurred between n—amyl borate and the following methyl esters: dimethyl sulfate, parahydroxy methyl benzoate, methyl salicylate, and methyl stearate. Interchange also took place between methyl stearate and tribenzyl borate, tri—n—propyl borate, and tri—m, p—cresyl borate. Highest yields and purities resulted from reactions involving methyl stearate. Catalysts employed were magnesium—aluminum ethylate and aluminum Isopropoxide.

Two methods of separating the methanol—methyl borate azeotrope were evaluated: sulfuric acid extraction and salt splitting. Extraction with sulfuric acid was determined to be the …

A Study Of Continuous Photochemical Hydrolysis, Robert Parlante, Theodore Arthur Gropler

Theses

In this investigation, the ultraviolet absorption spectra and the batch photochemical hydrolysis of monochloroacetic and monobromoacetic acid, and their potassium and sodium salts, have been measured and compared with those existing in the literature.

The continuous photochemical hydrolysis of sodium chloroacetate has been investigated for the first time. The continuous photolysis of uranyl oxalate was investigated and used as a chemical actinometer.

Gaseous material in the reactant feed has been found to be important at low flow rates.

Prediction Of Ternary Azeotropes From Binary Data, Eric Lustig

Theses

The Margules equation as modified by Wohl for ternary liquid-vapor systems, is used to develop ternary activity coefficients at different concentrations and varying temperatures. Corresponding binary experimental data are necessary to mathematically obtain these ternary activity coefficients. A trial and error graphical technique is used to examine the ternary data for azeotropic conditions. Convergence on ternary graph paper can be easily detected after the first two trials. Divergence is an indication that the system under consideration is nonazeotropic.

Most of the azeotropic systems investigated agreed quite well with published data. The range of disagreement of concentrations for component a in …

The Investigation Of Frequency Response And Stability Of A Heat Exchanger Under Condensate Control, Louis F. Fornoff

Theses

Control of a condensing steam heat exchanger by condensate throttling was investigated theoretically by a frequency response analysis. The theoretical analysis was verified by experimental operation of the heat exchanger.

The system was characterized by heat transfer calculations and Laplace transform functions. The transfer functions were used to complete a frequency response analysis of the system which predicted the controller settings, the stability of the system and its response to a step set point change. The calculations were verified by experimental operation and reasonable agreement was obtained.

It was calculated that condensate throttling can be used to obtain stable control …

Isobaric Vapor-Liquid Equilibria System : Benzene, Chlorobenzene, Phenol, Larry Madestau

Theses

Isobaric vapor-liquid equilibria were determined experimentally for the three binary systems benzene-chlorobenzene, benzene-phenol, and chlorobenzene-phenol; and for the corresponding ternary system benzene-chlorobenzene-phenol. Constants for the Chao modified Redlich-Kistler equations were calculated from the experimental data by the method of least squares. These constants were then used to predict vapor-liquid equilibria for the ternary system. The predicted values showed satisfactory agreement with those found experimentally.

A modified Ellis still was used for obtaining equilibrium data. Samples of vapor and liquid phases were analyzed by means of the F & M Model 720 vapor phase chromatograph. Benzene, chlorobenzene, and phenol used in …

Characterization Of Synthetic Resins Used In Graphite Extrusion Process, Charles I. Fairchild

Chemical and Biological Engineering ETDs

Six furan resins and one epoxy resin were used in tests to determine coking values and gas evolution characteristics of the resins. The same resins, except the epoxy, were used as binders in extruded graphite rods to determine environmental factors affecting the coked density of the rods.

Coking values of the resins containing three different activators were determined by measuring residue remaining after heat treatment to 850° C. Coking values 54-56% were obtained with 8 phr to toluenesulfonic acid actiator.

Gas evolution curves were obtained by measurement of pressure rise in a constant volume apparatus during heating to 300° C …

Effects Of Gamma Radiation On Ion Exchange Membranes., John R. C. Roop

Masters Theses

No abstract provided.

Permeability Of Organic Protective Coatings And Relation To Film Thickness, Bipin N. Doshi

Masters Theses

“Special types of coating systems are used to protect industrial products and structures against corrosion. Many millions of dollars are spent each year for these coatings. The ability of protective coatings to reduce or inhibit corrosion depends on a variety of factors such as dry film thickness, resistance to permeation of ions and vapors, temperature, pressure, structure of binder, nature of pigment, electrolytic resistance, and many others.

The initial work done by Larry Inglis on the permeability of coatings and it's relation to thickness of coating films showed that the permeability, as determined by under film corrosion, was independent of …

The Removal Of Abs From Tap Water Solutions And Sewage Plant Effluents At Various Air Rates Using Continuous Foam Flotation., Ratan F. Daboo

Masters Theses

"This investigation was performed to study the removal of Alkyl Benzene Sulfonate (ABS) from tap water solutions and sewage treatment plant effluents by continuous foam flotation and to determine the effect of the air flow rate on the removal.

A flotation cell provided with controlled air and liquid flow rates was used for the continuous process. Air flow rates between zero and 29.4 cubic feet per hour were investigated. A liquid feed flow rate of 120 milliliters per minute was used for most of the experiments with one run made at 60 milliliters per minute. The liquid samples were analyzed …

The Performance Of A Mechanically-Aided Countercurrent Extraction Column., Jerry James Carr

Masters Theses

"In recent years liquid extraction has become a major industrial method for the separation of liquid solutions. Liquid extraction has proven successful in some separations performed only with great difficulty by other, more common mass-transfer operations. Th e industrial utilization of liquid extraction has resulted in considerable interest in the design and performance correlations of high-capacity, high-efficiency extraction equipment.

Continuous countercurrent columns, filled with various packings, baffles, and plates, have been found to be relatively ineffective in liquid extract on service. The density difference of the contacted phases is generally insufficient to, by itself, cause the intimate contact necessary for …

Viscosities Of Various Binary Non-Polar Gaseous Mixtures., Gerald Lee Stevenson

Masters Theses

"Viscosity is an important physical property involving the transport of momentum in a fluid. Momentum is transferred within a fluid under an existing velocity gradient as the driving force. Since momentum transfer is actually attained by the dynamic interaction between particles of mass, a description of molecular interaction is essential in order to accurately predict the viscosity of a fluid. Temperature affects fluid viscosity by increasing the kinetic energy of the fluid system and thus the frequency by which molecules are involved in interaction. There have been many theoretical studies made concerning the intermolecular potential energy statements which serve as …

Separation Of Radioactive Fission Products By Electrodialysis Using Aminopolycarboxylic Acids., Harry C. Hershey

Masters Theses

"The development of nuclear fission reactors to convert nuclear energy into electrical energy for use in industry, public utilities, military applications, and space exploration has resulted in ever increasing quantities of radioactive waste solutions. Significant reductions in nuclear fuel costs will be obtained when economical processes have been developed for recovery and purification of valuable fission products which are contained in radioactive waste solutions and are in demand for many research applications.

The United States Atomic Energy Commission has supported exhaustive studies to recover fission products by processes involving the more common unit operations such as extraction, distillation, crystallization, and …

The Construction And Evaluation Of A Small Scale Laboratory Fermentor For Batch And Continuous Studies., Robert Murray Logan

Masters Theses

"The purpose or this investigation was to design and construct a suitable apparatus for the aerobic culture or microorganisms to be used for preliminary batch studies and eventually, continuous fermentations.

The general design of the apparatus was patterned after small scale equipment described in the literature. Construction or the apparatus was carried out in the shop of the Department of Chemical Engineering and Chemistry. All of the necessary machining was done by the author.

The aeration-agitation system was evaluated by the use or the sulfite oxidation rate determination. The oxygen transfer rate provided by the apparatus was round to be …

A Study Of The Dissolution Of Titanium-Oxygen-Nitrogen Alloys In Hydrofluoric Acid, Arliss V. Martin

Doctoral Dissertations

"The purpose of this investigation was to study the effect of oxygen and nitrogen (in the alpha solid solution range) on the kinetics and electrochemistry of titanium dissolution in hydrofluoric acid. Dissolution rates, activation energies, difference effects, and potential measurements were determined with TiO_XN_Y sintered alloys and sheet metal. Values of x ranged from 0.01 to 0.126 and values of x. from 0.001 to 0.230.

Dissolution rates were determined using a gas evolution technique. Temperatures were varied from 5 to 45°C. The hydrogen evolution rates were converted to TiO_XN_Y dissolution rates by means of …

Development Of A Technique For The Determination Of Capillary Pressure Curves Using A Constantly Accelerated Centrifuge, Robert N. Hoffman

Masters Theses

"A new technique for determining capillary pressure curves with a centrifuge has been developed and tested. Capillary pressure curves were determined for six cores by this technique and were compared to the curves for the same cores determined by the semi-permeable barrier technique. The technique differs from previously reported centrifuge techniques in that the centrifuge was slowly accelerated from zero to the maximum desired speed, rather than being held constant at particular, progressively higher speeds. An important advantage of this technique over other methods for determining capillary pressure curves is the short time required to obtain the desired amount of …

The Separation Of Strontium-90 From Cesium-137 And Fractionation Of Rare Earth Elements By Liquid-Liquid Extraction., Surendra D. Khanna

Masters Theses

No abstract provided.

Permeability And Adsorbed Flow Of Carbon Dioxide And Propene Through Porous Silica., Jorgen Lovland

Masters Theses

"It has been known for over a century that gases diffuse through some porous barriers at a rate inversely proportional to the square root of the molecular weight. The difference in diffusion rate can obviously be used to separate gases with different molecular weight. Since other methods for separation like distillation and adsorption usually are simpler and cheaper, separation by gaseous diffusion has found few practical applications. One notable exception is the separation of the gaseous hexafluorides of u²³⁸ and u²³⁵.

Later investigations on the permeation of gases through porous materials have shown that when gases diffuse …

Processibility Factors Of Polyolefins As Determined On The Brabender Plastograph, James Thomas Ryan

Theses

Some knowledge of the behavior of a plastic during processing is required if the materials best properties for a given application are to be retained. For thermoplastic polymers¹ changes in viscosity, a function of molecular weight, can be measured by various laboratory instruments, generally, under specialised conditions. One laboratory instrument, however, called the Brabender Plastograph will, it is claimed by the C. W. Brabender Company, measure the viscosity behavior of plastics under conditions found in production equipment. The Brabender plastograph measures changes in torque, a function of viscosity, which result from chain scission, shear thinning, temperature effect, density change …

A Study Of A Continuous Photochemical Reactor, John Calvin Roe

Theses

The purpose of the investigation was to construct a continuous photochemical reactor, to reinvestigate certain portions of the work of Gaertner and Kent (7) and to extend the work to include some of the more common photochemical reactions.

A reactor of annular design with an elliptical light reflector, similar to that of Gaertner and Kent, was designed and constructed. The sources of radient energy were a cold General Electric T-6 Germicidal Lamp and a hot General Electric UA-9 Lamp.

The photochemical decomposition of oxalic acid sensitized by the uranyl ion was utilized as an actinometer. Fifty continuous runs were accomplished …

Extraction Of Technical Grade Lactic Acid With N-Butyl Alcohol, Joel Howard Kaplan

Theses

A possible step in a proposed industrial method for purifying and concentrating technical grade (44 per cent) lactic acid was investigated. The proposed method is the extraction of lactic acid from the crude grade by n-butyl alcohol, esterification of the extract by n-butyl alcohol and hydrolysis of the resultant purified ester to pure lactic acid. The extraction of lactic acid by n-butyl alcohol from the crude grade was the topic considered in this paper.

The extraction process was carried out at temperatures of 10.2°C, 25.0°C, 40.0°C and 60.00C using both U. S. P. lactic acid (85 per cent) and technical …

Preparation Of Aryl Sulfones By Sulfonation In The Presence Of Phosphrous Oxychloride, Donald Frederick Kruse

Theses

The use of phosphorus oxychloride as a dehydrating agent in the sulfonation of aromatic compounds has been investigated, particularly with respect to the formation of aryl sulfones. The sulfonation of several aromatic compounds using reagent grade sulfuric acid and phosphorus oxychloride has produced sulfone yields which exceed yields reported in the literature and obtained by more tedious methods. The presence of alkyl side groups on the benzene ring generally favors high yields of sulfone; whereas the presence of halogens generally reduces the yield. Sulfone formation is shown to be dependent upon the reactant ratios and upon the reaction time and …

An Evaluation Of Oxide Films Of Lead And Tellurium Prepared By Reactive Sputtering, Frank Groom Peters

Theses

Oxide films of lead, tellurium, and their alloys were deposited by reactive sputtering onto substrates and analyzed by X-ray emission spectrography. The sputtering process involved the bombardment of a metallic cathode with positive ions in an atmosphere containing oxygen. The preparation and analysis of these films are described. The unstrained, homogeneous films have good adherence to the substrate and may be prepared to arbitrary thicknesses. Over a range of lead-tellurium oxide compositions these films are transparent and are glassy, rather than crystalline or amorphous solids.

From the analyses of the films by X-ray emission spectrography and known cathode compositions, it …

The Suspension Of Spherical Glass Beads In Water, David Isert, Andrew G. Zourides

Theses

The purpose of this investigation was to determine, for the first time, a correlation between mixing and fluidization in a system of spherical glass beads and water.

Mixing data for the spherical glass bead-water system was obtained experimentally and abstracted from previous studies.⁽¹⁾

Fluidization data for the spherical glass beadwater system was obtained from the literature.⁽²⁾

The terminal velocity and the Reynolds Number at terminalization was calculated for the mixing system from the data obtained in this investigation. The terminal velocity and Reynolds Number, as determined experimentally was obtained from the literature,⁽³⁾ A comparison of the terminal …

Viscosity-Vapor Pressure Correlation Of Alcohols, Methyl Ketones And Alkyl Halides, Kevin Frank

Theses

A linear relationship was found to exist between the logarithms of viscosity and vapor pressure measured at the same temperature for certain homologous series. Previous work by Di Geronimo, healing, and McGuire substantiated this correlation for n-paraflin hydrocarbons, n-paraffin fatty acids and esters, n-alkyl cyclohexanes, n-alkyl benzenes and n-l-monoolefins. The relationship takes the form

logη= A log vp + B

where A and B are constants characteristic of the homologous series.

The adaptation of this linear relationship to alcohols methyl ketones, and alkyl halides in the present work indicates a wide applicability of the correlation. the values of the series …

Properties Of Non-Newtonian Fluids, George Robert Ferment

Theses

The purpose of this work was to investigate the fluid properties of non-Newtonian solutions.

The effect of temperature on the viscometric properties, flow behavior index (n) and fluid consistency index (K), was investigated. It was established that the flow behavior index was temperature dependent, tending to approach Newtonian behavior as the temperature was raised. The fluid consistency index was also temperature dependent; a plot of K vs temperature will yield a straight line on semilogarithmic coordinates.

The specific heats of non-Newtonian solutions were also determined. For systems containing large mass fractions of water, it was established that the presence of …

Modified Coates-Orr Vapor-Liquid Equilibrium Still : The Effect Of Pressure On Binary Azeotropes, John K. Jacob

Theses

In order to test the effect of pressure on binary azeotropes, an all stainless steel Coates-Orr vapor-liquid equilibrium still was constructed and then tested at atmospheric and superatmospheric pressure. To overcome operating difficulties at superatmospheric pressures, it was necessary to modify the original still design by (1) coiling a Nichrome resistance wire around the entire still body and insulating heavily over the coil, (2) substituting a "canned" seal-less pump in place of the original centrifugal pump.

A survey of the literature shows that the difficult-to-operate Jones-type equilibrium stills, from which the Coates-Orr still was developed, approach true phase equilibrium. Therefore, …

Heat Conductivity Of Adhesively Bonded Assemblies, Stanley I. Klosowski

Theses

The thermal conductivity of an epoxy compound commonly used as an adhesive, was measured using asimple apparatus specially designed to simulate adhesion, to minimize heat losses, and to simplify measurement and correction for heat losses. Variation of heat conductivity coefficient with glue line thickness and temperature was investigated. The results do not indicate that there is any consistent correlation between the heat conductiv¬ity coefficient and glue line thickness or between heat conductivity coefficient and temperature. However, the small number of samples measured does not permit any definite conclusions to be drawn. The sample with glue line thickness below 0.025 millimeters …