Modeling Of Submarine Torpedo-Launching Simulation,
2019
Navy Submarine Academy, Qingdao, Qingdao 266100, China,;
Modeling Of Submarine Torpedo-Launching Simulation, Jinping Wu, Junchao Mao, Wenqiang Ding
Journal of System Simulation
Abstract: In order to lay foundation for modeling and simulation of operation problems such as torpedo attacking, torpedo operation application and torpedo operation effectiveness analysis, etc., the model of submarine torpedo-launching is built in the way of qualitative analysis and classical mathematics. As an important composition of submarine torpedo-attacking, torpedo-launching mainly means the course from torpedo out-tube to hitting target or voyage end, which is between the stage of “controlling weapon launching” and “observing attack effectiveness” during the whole torpedo-attacking course. Through analyzing the seven-stage trajectory process of torpedo-launching, the target detecting model and acoustic homing range model of …
Design And Implementation Of Signal Level Mono-Pulse Tracking Radar Simulation System,
2019
1.Army Engineering University, Shijiazhuang 050003, China; ;
Design And Implementation Of Signal Level Mono-Pulse Tracking Radar Simulation System, Chaoxuan Shang, Zhao Yang, Zhuangzhi Han, Han Ning
Journal of System Simulation
Abstract: In view of the poor compatibility between the particle size of simulation and tracking feedback control in tracking radar simulation system, a signal level mono-pulse tracking radar simulation system is constructed based on SystemVue simulation platform. Simulation system is layered and simulation framework is built according to the requirements of the simulation system. The key technologies in the process of simulation are analyzed, and the simulation results with distance and angle tracking loop are given. System implementation is of great significance for mono-pulse radar system design, demonstration, equipment development appraisal as well as combat training and …
Adaptive Fuzzy Sliding Mode Controller With Predictive Control For Redundant Manipulators With Variable Payload,
2019
1.School of Information Science and Technology, University of Science and Technology of China,Hefei 230026, China; ;2.Institute of Advanced Manufacturing Technology, Hefei Institute of Physical Science, Chinese Academy of Sciences, Changzhou 213164, China;
Adaptive Fuzzy Sliding Mode Controller With Predictive Control For Redundant Manipulators With Variable Payload, He Jun, Minzhou Luo, Jianghai Zhao, Linsen Xu, Li Tao
Journal of System Simulation
Abstract: This paper presents an adaptive fuzzy sliding mode controller with Kalman predictive control (AFSMCK) for the redundant robotic manipulator handling a variable payload to achieve a precise trajectory tracking in the task space. This approach could be applied to solve the problems caused by the variable payload and model uncertainties. A Kalman predictive controller using the recursive algorithm is presented for an accurate prediction of a variable payload. The adaptive fuzzy logic algorithm is designed to approximate the parameters of the sliding mode controller to avoid chattering in real time. Lyapunov theory is applied to guarantee the stability of …
Modeling And Numerical Simulation Of Tissue Engineering Scaffold 3d Printing Process,
2019
College of Mechanical & Power Engineering, China Three Gorges University, Yichang, 443002, China;
Modeling And Numerical Simulation Of Tissue Engineering Scaffold 3d Printing Process, Congping Chen, Jieguang Huang, Hu Qiong, Yanhua Ran, Li Bo
Journal of System Simulation
Abstract: In the process of tissue engineering scaffold fabrication using injecting 3D printing, the viscous fluid material is extruded out with a style of microfilament, which is deposited on a substrate layer by layer. The materials spread, pile up, remelt and solidify as a consequence of the couple effects of gravity, surface tension, viscous force and solidification drag force. Aiming at the above issues, the forming process of scaffold with homogeneously-sized space pores is studied with a CFD approach to research the pore forming mechanism. The results show that the viscous fluid is cooled mainly by the substrate, and heat …
Parameter Identification For Pmsm Based On Multi-Innovation Approximate Least Absolute Deviation Identification Algorithm,
2019
Key Laboratory of Advanced Process Control for Light Industry, Ministry of Education Jiangnan University, Wuxi 214122, China;
Parameter Identification For Pmsm Based On Multi-Innovation Approximate Least Absolute Deviation Identification Algorithm, Dinghui Wu, Jianyu Zhang, Yanxia Shen, Zhicheng Ji
Journal of System Simulation
Abstract: In view of the problem that the results of traditional identification algorithm are not accurate caused by the peak noise signal in the environment, a new algorithm based on the forgetting factor multi-innovation approximate least absolute deviation (MIALAD) identification algorithm is proposed. Combined with the system voltage equation of permanent magnet synchronous motor (PMSM), a discrete identification model is constructed. By using vector control method, the input and output data of the identification model are obtained to identify the rotor resistance and inductance. The simulation results show that this identification algorithm can obtain the accurate parameters of the PMSM …
Discrete Control Simulation Of Agitation Tank Based On Taylor Finite Difference,
2019
School of Data and Computer Science, Sun Yat-sen University, Guangzhou 510006, China;
Discrete Control Simulation Of Agitation Tank Based On Taylor Finite Difference, Yunong Zhang, Yaqiong Ding, Le Li, Deyang Zhang, Binbin Qiu
Journal of System Simulation
Abstract: Zhang dynamics is used to solve the system equations of the agitation tank to get controllers. At the same time, Taylor finite difference method is used in the computer discrete control simulation for the agitator tank system. In addition, the convergence stability of Zhang dynamics applied to the agitation tank is proved through theoretical analysis. In order to achieve the draining purpose for the agitation tank, the computer discrete control simulation is conducted by means of MATLAB. For comparison, the computer simulation based on the neural network predictive controller is carried out. The comparative simulation results substantiate the …
Structure Optimization Analysis Of Multi-Span Antisymmetric Arch Tower Cable-Stayed Bridge,
2019
School of Mechanical Engineering, Tianjin University, Tianjin 300354, China;
Structure Optimization Analysis Of Multi-Span Antisymmetric Arch Tower Cable-Stayed Bridge, Xijun Liu, Yuan Bo, Tianyi Liu
Journal of System Simulation
Abstract: In order to analyze its force under different sections and arch span ratio of the Antisymmetric arch tower cable-stayed bridge, the paper takes an anti-symmetric arch tower cable-stayed bridge as an engineering example. Considering the effect of dead load and temperature, finite software is used to calculate the stress of the arch tower and deflection of the deck and its corresponding dynamic characteristics under different types of arch sections and different rise-span ratio of the arch. The results show that the circular cross-section has better mechanical performance compared with other types of arches tower section with the same …
Interval Fuzzy Modeling Based On Minimizing-Norm On Approximation Error,
2019
College of engineering and technology, Zunyi Normal College, Zunyi 563002, China;
Interval Fuzzy Modeling Based On Minimizing-Norm On Approximation Error, Xiaoyong Liu, Zhonggang Xiong, Changguo Yan
Journal of System Simulation
Abstract: As the obtained data in many practical applications tend to be uncertain or inaccurate, conventional modeling methods characterized by deterministic model for this type of data have become undesirable. Taking linear programming and TS fuzzy model and some ideas from norm minimization into consideration, a novel method identifying interval fuzzy model (INFUMO) consisting of upper and lower TS fuzzy model (referred to as fU and fL) has been studied. In order to solve INFUMO, optimization problems based on minimizing-norm with respect to approximation error corresponding to fU and fL are constructed. Finally, optimization problems …
Prediction Model Of Particle Size Distribution In Bauxite Continuous Ball Milling Process,
2019
1.College of Physics and Information Science, Hunan Normal University, Changsha 410006, China; ;
Prediction Model Of Particle Size Distribution In Bauxite Continuous Ball Milling Process, Tianyu Ma, Yalin Wang, Kun Shen, Jinping Liu
Journal of System Simulation
Abstract: As it is difficult to detect the particle size distribution of ball milling process on line, a prediction model of particle size distribution in bauxite continuous ball-milling process is proposed, which is based on data-driven method and population balance model (PBM) frame. The break-rate model structure of PBM is improved according to the characteristic data of batch grinding test of bauxite. The residual time distribution density function is improved by considering the characteristics of residence time distribution for different particle sizes. The key parameters of the model are optimized by the data of batch-test and continuous ball-milling process using …
A Method Of 3d Scattering Center Extraction Based On Multiple Hrrp Series,
2019
Science and Technology on Electromagnetic Scattering Laboratory, Beijing 100854, China;
A Method Of 3d Scattering Center Extraction Based On Multiple Hrrp Series, Cui Shan, Li Sheng, Yan Hua
Journal of System Simulation
Abstract: Scattering center extraction is the key content in the research of radar target characteristics, particularly the sliding type of scattering center. An extraction method based on the parametric scattering center model is proposed, which takes advantage of Hough transformation to extract geometric location and sliding radius parameters. The distance is gotten in the line of radar sight, and the useful information is obtained from high-resolution range profile (HRRP) series, which estimates size parameter of scattering centers and accomplishes signal reconstruction. This method solves the problems of point and sliding scattering center extraction. Simulation example manifests the applicability of the …
Modeling And Simulation Of The Crosstalk On Aircraft Arinc429 Data Bus,
2019
1.Aviation Ground Special Equipments Research Base, Civil Aviation University of China, Tianjin 300300, China; ;2.College of Electronic Information and Automation, Civil Aviation University of China, Tianjin 300300, China;
Modeling And Simulation Of The Crosstalk On Aircraft Arinc429 Data Bus, Xudong Shi, Ruowen Wang, Jialin Wang, Hongxu Zhao
Journal of System Simulation
Abstract: Based on the theory of multi-conductor transmission line, the crosstalk between a single cable and a UTP (unshielded twisted pairs) cable was studied. The MATLAB and CST were employed to do the theoretical calculation and modeling respectively, and the comparison result proved the validity and accuracy of the proposed model. Based on the UTP model, the shielding layer was used to build the STP（shielded twisted-wire pairs） model according to the ARINC429 specification, and the crosstalk which caused by a large voltage transient happening on the adjacent power line on the aircraft was further analyzed. The distance and length of …
Simulation Of Stone Cutting Process Based On Adaptive Coupling Method,
2019
1.School of Mechanical Engineering, Hebei University of Technology, Tianjin 300130, China; ;2.Tianjin University of Technology and Education,Engineering Training Center, Tianjin 300222, China;
Simulation Of Stone Cutting Process Based On Adaptive Coupling Method, Yongjun Tian, Guolin Duan, Junguang Kang, Jianhua Gang
Journal of System Simulation
Abstract: Aiming at complex nonlinear dynamic behaviors of stone-cutting process with circular saw and handling large mesh deformation instability in FEM, according to brittle material fracture mechanism, an adaptive coupling algorithm was established for calculating the cutting process of circular saw-stone materials system. The results show that the material removal process is a process of intermittent cycle; the cutting force is zero at the beginning of the process, and the force increases rapidly when the blade contacts with the stone, then decreases, eventually varies in a stable fluctuation. According to von-Mises stress distributions of saw blade and stone, the easily …
Research And Simulation For Military Contests Based On Ahp And Entropy Models,
2019
Institute of Systems Engineering National University of Defense Technology, Changsha 410073, China;
Research And Simulation For Military Contests Based On Ahp And Entropy Models, Rusheng Ju, Zhengqiu Zhu, Yunxiu Zeng, Ruixian Wang, Xiaogang Qiu
Journal of System Simulation
Abstract: The paper studiesthe comprehensive military contests which are held frequently among military universities. Different from the qualitative analysis methods before, an analytic hierarchy process model is set up to analyze the effects which training programs have on students. A great amount of data is put into the entropy model to analyze the rationality of AHP model. This paper also sets the effect value as the input data of the emulating model to simulate the whole exercise process before contests which can verify the results received from AHP and entropy models. Research findings are helpful for superior leaders to make …
Research On Wind Turbine Test System Based On Jointsimulation,
2019
School of Mechanical Engineering, Hebei University of Technology,Tianjin 300130, China;
Research On Wind Turbine Test System Based On Jointsimulation, Zhongyue Song, Zhen Dong, Zhang Hao, Zhanqun Shi, Jiaojiao Ma
Journal of System Simulation
Abstract: As the test equipment of wind turbine can not simulate wind driven exactly and the impact of environmental factors is hard to be taken into account, the simulation results have larger errors. The problem is solved by establishing the virtual test bench in the way of combined simulation. The wind speed modelis optimized by combining the fitting of probability and the combinated wind speed model to drive the wind turbine;and the settings of some relevant contact force parameters are considered,which canmake the simulation results are closer to the actual situation. The credibilityof the system isdemonstrated and the validity …
Review On Modeling And Simulation Of Cyberspace Operation,
2019
Joint Operations College of National Defence University, Beijing 100091, China;
Review On Modeling And Simulation Of Cyberspace Operation, Guangya Si, Zhang Yang, Yanzheng Wang
Journal of System Simulation
Abstract: Modeling and Simulation (M&S) is the effective and indispensable method to research cyberspace operation. On the view of joint operation level, the evolution feature of the cyberspace operation M&S is analyzed, which includes the constructions of the cyberspace weapons range, the cyberspace operation concept environment, and the cyberspace operation command information system. The progress of the cyberspace operation M&S is introdeced, including the networked information environment, the entity, the action and the effection. The new challenges of the cyberspace operation M&S are analyzed from the military angle and technology angle.
Fault Detection Based On Gpnmf For Industrial Process,
2019
1.State Key Laboratory for Alternate Electric Power System with Renewable Energy Source, North China Electric Power University, Beijing 102206, China; ;
Fault Detection Based On Gpnmf For Industrial Process, Yuguang Niu, Shilin Wang, Zhongwei Lin, Xiaoming Li
Journal of System Simulation
Abstract: As a newly dimension reduction technique, non-negative matrix factorization (NMF) has been applied in varying research areas. NMF methods require the original data non-negative. However, the operating data of industrial process maybe not satisfy this restriction. To resolve the problem, a new method is presented, which can be called as generalized projection non-negative matrix factorization (GPNMF). We use GPNMF to extract the latent variables that drive a process and to combine them with process monitoring techniques for fault detection. The corresponding contribution plots are defined for fault isolation. The proposed method is applied to a 1 000 MW unit …
Design Of Ground Online Flight Simulation System,
2019
1.AVIC CHENG DU AIRCRAFT INDUSTRIAL (GROUP) CO., LTD, Chengdu 610091, China; ;
Design Of Ground Online Flight Simulation System, Changgui Yu, Hongrui Xiong, Tian Kai, Chuntao Li
Journal of System Simulation
Abstract: Aiming at the high cost and the immovable characteristics of the airplane iron bird test-bed and the semi-physical simulation laboratory, a highly integrated and movable system named as ground online flight is introduced. The dynamics and kinematics of unmanned aerial vehicle, sensors model, engines model and related subsystems are established and integrated into a device; the connections of 1553B, RS422, analog signal, discrete signal, pulse signal, PWM signal and so on are implemented. The wind model and the typical system faults are set up to study the robustness of the UAV, and test the UAV strategy which …
Evaluation Of Simulation Credibility Based On Rough Set And Gray Correlation Analysis,
2019
School of Information Engineering, Inner Mongolia University of Science and Technology, Baotou 014010, China;
Evaluation Of Simulation Credibility Based On Rough Set And Gray Correlation Analysis, Huibo Liu, Yongjie Qian
Journal of System Simulation
Abstract: The evaluation of simulation model credibility has always been a hot issue in the simulation field. How to evaluate the credibility of the simulation is the key to the development of the simulation technology. It is of great significance for our country to carry out the credibility evaluation research. In view of the issue, the grey correlation analysis theory and the related principles in rough set theory are analyzed and the simulation credibility evaluation model based on rough set and grey correlation analysis is proposed. The indiscernibility principle in rough set is used to assign the weight distribution of …
An Autonomous Cognitive Model Simulating Basal Ganglia Mechanism,
2019
1.School of electronic information and automation, Civil Aviation University of China, Tianjin 300300, China; ;
An Autonomous Cognitive Model Simulating Basal Ganglia Mechanism, Zongshuai Li, Chen Jing
Journal of System Simulation
Abstract: Aiming at autonomous cognition problem, applying the winner-takes-all(WTA) learning mechanism, using cortical-striatal synaptic modification principle in basal ganglia, as well as based on the operant conditioning reflex theory, the basal ganglia autonomous cognitive model is established, which is suitable for the cognitive learning with limited actions. Skinner's pigeons experiment was simulated by applying this bionic learning model, which showes a gradual process of adaptive learning. The simulation results reflect that the proposed cognitive model is effective and can be used in the balance learning for a self-balancing robot. In the premise of unknown robot mathematical model, the purpose of …
Simulation Of Taxi Passenger Travel Mode Considering The Influence Of Online Booking Taxi,
2019
Southwest Jiaotong University, school of transportation and logistics, Chengdu 610031, China;
Simulation Of Taxi Passenger Travel Mode Considering The Influence Of Online Booking Taxi, Cao Yi, Yanjin Li, Luo Xia
Journal of System Simulation
Abstract: To reflect a systematic account of the impact online booking taxi and cruise taxi under the condition of information, the travelling mode choice of taxi passengers was researched. The influence factors of travelling mode choice of taxi passengers were analyzed and the time values related to passenger’s own characteristics were evaluated. The functions of waiting time of online booking taxi passengers and cruise taxi passengers were formed by investigating the difference of searching behavior. Through using simulation method, the priority for online booking taxi, cruise taxi and private cars was obtained .The results showed that the online booking …
