Industrial Technology Commons^™

Choice Of Instruments For Verification And Calibration Of Gas Analyzers, Ortigali Khakimov, Paraxat Mayliyevna Matyakubova, Mirolim Muhammad O'G'Li Maxmudjonov

Chemical Technology, Control and Management

This article analyzes the process of metrological control of gas analyzers and metrological requirements for them. The current state of the standards used in the state metrological control of gas analyzers and the results of the analyzes were studied. The task of choosing the measuring instruments used in the verification process and optimizing the requirements for them is set. An experimental verification process was organized in three groups using several measuring devices, and the reliability of the verification results was assessed. With the use of modern measuring instruments, a graph of the output value was built during the experimental verification …

Modeling And Adjustment Of A Fuzzy Controller In A Bioreactor Control System, Mahmudov Giyosjon Baqoyevich

Chemical Technology, Control and Management

The article describes the modeling and configuration of a fuzzy controller for the control system of the bacterial oxidation of hard-to-enrich gold-bearing sulfide ores. The simulated logical fuzzy controller allows you to save the consumption of refrigerant water consumed in the process by 4,3%, using it to control the process of bacterial oxidation.

Mathematical Description Of A Bleach Impregnation Reservoir, Bekobod Ibragimov

Chemical Technology, Control and Management

This article discusses the issues of constructing a mathematical model of the technological process of bleaching textile materials in an impregnating reservoir using the heat balance equation, on the basis of which a qualitative analysis of the dynamic properties of an object has been carried out in order to create highly efficient control systems with the use of energy-saving technologies. While constructing a mathematical model characterizing the established and non-established modes of the control object (impregnating reservoir) used changes in heat flow and mass velocity of the incoming tissue. An algorithm for constructing a mathematical model of the process of …

Mathematical Description And Algorithm For Solving The Model Of The Ionite Regeneration Process In The Ion Exchange Method Of Water Softening, Djalolitdin Paxritdinovich Mukhitdinov, Nilufar Abdusami Qizi Yunusova

Chemical Technology, Control and Management

Based on the modern representation of the water softening process by the ion exchange method, modeling was carried out, an algorithm was developed and the ionite regeneration process was calculated in a water softening plant with a fixed ionite layer. To solve the system of equations of the model, special, but simple enough for use in engineering calculations, techniques and methods have been developed and applied. The constructed model and its solution algorithm can be used to predict the process of ionite regeneration in an ion exchange apparatus. It can also be used to calculate the time of the ionite …

Synthesis Methods And Algorithms For Expanding The Dynamic Range Of The Adc, Jumaev Odil Abdujalilovich, Rashidov G'Olibjon Xayriddinovich

Chemical Technology, Control and Management

The modern development of new technologies, in particular, the intensive use of programmable logic integrated circuits in digital information processing tasks, allows for algorithmically and programmatically solving problems, opens up real opportunities to increase accuracy and ensure the required signal conversion speed, and also, it will be possible to take into account the effects of noise and their elimination over the entire time interval band. The article discusses the main methods of digital information processing, analyzes the ways and possibilities of expanding the dynamic range of analog-to-digital converters, as well as the synthesis of appropriate conversion devices, primarily digital filters.

Synergetic Synthesis Of Multivariate Nonlinear Dynamic Objects, Isamiddin Siddikov, Komil Usmanov

Chemical Technology, Control and Management

Based on the synergetic approach, the article solves the problem of analyzing a chemical reactor as a control object and formulates recommendations on the structural and topological synthesis of various control system options. The main feature of technological control objects, in which, as a result of hydromechanical, physical, chemical influences on the flows of the starting substances, their physical properties, state of aggregation and composition change, is their multidimensionality, nonlinearity, multiconnectedness, as well as parametric uncertainty of the mathematical model at the design stage. This type of facility includes a chemical reactor, thermal management, which in most cases is carried …

Methods And Algorithms For Monitoring And Prediction Of Various Fire Hazardous Situations, Mizaakbar Xakkulmirzayevich Hudayberdiyev, Oybek Zokirovich Koraboshev

Chemical Technology, Control and Management

This article analyzes emergency situations arising from natural disasters (fires, explosions, earthquakes, floods, landslides, etc.) and man-made accidents. The event in which the values of fire risks in the area decrease uniformly and at the same time the amount of fire risks is minimal is considered optimal. Models, methods, and logistic regression algorithm have been used to predict fire hazard situations and identify potential fire safety measures.

Development Of Detection And Tracking Systems For Autonomous Vehicles Using Machine Learning, Tyler Ward

Morehead State Theses and Dissertations

A thesis presented to the faculty of the Elmer R. Smith College of Business and Technology at Morehead State University in partial fulfillment of the requirements for the degree of Master of Science by Tyler Ward April 25, 2023.

Improving Network Security For High Schools In Carolina, Southeastern, And South Central Conference, Eden Sampson

Campus Research Month

Cybersecurity is a very important factor that is often overlooked until one becomes a victim of hackers and viruses. One of the main institutions that are caught off guard by cyber issues are high schools. Adventist high schools often fall into this issue as well. It is very dangerous because of the sensitive information handled on school networks as well as the financial loss that cyber security attacks may cause. Moreover, just a few Adventist high schools have IT staff who are qualified to protect the school from cyberattacks or to help with recovery. Therefore, our contribution is to create …

Fast And Accurate 3d Object Reconstruction For Cargo Load Planning, Adam R. Nasi

Theses and Dissertations

Cargo load planning involves efficiently packing objects into aircraft subject to constraints such as space and weight distribution. Currently, this is performed manually by loadmasters. The United States Air Force is investigating ways to automate this process in order to improve airlift operational readiness while saving money. The first step in such a process would be generating 3D reconstructions of cargo objects to be used by a load planning algorithm. To that end, this thesis presents a novel method for fast, scaled, and accurate 3D reconstruction of cargo objects. This method can scan a 2.5m×3m×2m object in less than 10 …

Automated Registration Of Titanium Metal Imaging Of Aircraft Components Using Deep Learning Techniques, Nathan A. Johnston

Theses and Dissertations

Studies have shown a connection between early catastrophic engine failures with microtexture regions (MTRs) of a specific size and orientation on the titanium metal engine components. The MTRs can be identified through the use of Electron Backscatter Diffraction (EBSD) however doing so is costly and requires destruction of the metal component being tested. A new methodology of characterizing MTRs is needed to properly evaluate the reliability of engine components on live aircraft. The Air Force Research Lab Materials Directorate (AFRL/RX) proposed a solution of supplementing EBSD with two non-destructive modalities, Eddy Current Testing (ECT) and Scanning Acoustic Microscopy (SAM). Doing …

Model For Calculating The Static Characteristics Of Hydraulic Systems Of Hydro Technical Buildings, Mirkhalil Ismailov, Dong Zhang, Farkhod Kasimov

Chemical Technology, Control and Management

Hydraulic mechanisms that actuate flat gates, widely used in hydraulic structures, are studied as hydraulic actuators of the system. Their static mathematical models are developed using an integrated methodology with a hydraulic pump, inlet and suction pipes, and internal and external resistance factors. Unlike existing mathematical models, the model developed in this paper allows a detailed description of the characteristics of hydraulic drives due to the fact that pressure losses in the throttle, regulator, and power amplifier, as well as local resistances in hydraulic pipelines, are taken into account.

Synchronization Of The Training Of Specialists In The Automation Of Technological Processes In Accordance With The Dynamics Of The Taxonomy Of Learning Goals, Yusuf Shodievich Avazov, Kamola Abdullaeva

Chemical Technology, Control and Management

Changes in the characteristics of modern ones, reflecting them as the "digital generation", inevitably necessitate electronic interactive, mobile and mixed, machine learning, especially in the field of automation and control of technological processes and production. As a consequence of reflecting these realities, there have been parallel changes in the taxonomy of learning objectives - from the classical to the revised rethought and digital.

In order to study the problem of synchronizing the training of future specialists in the field of automation and control of technological processes and production and funny knowledge in accordance with the dynamics of the taxonomy of …

Analysis Of Vegetable Oil Refining Technology, Elyor Samadov

Chemical Technology, Control and Management

Innovative technologies for refining vegetable oils are presented, as well as the qualitative characteristics of raw vegetable oils obtained by extraction and mechanical methods. A general review of the chemical composition and impurities of vegetable oils resulting from the reaction between glycerol and fatty acids is carried out, and a brief review of the study to determine the effect of refining on biologically active components.

The analytical review is devoted to a comparative comparison of two types of refining - chemical and physical refining.

Research Of Three-Phases Current’S Transducers Of Filter-Compensation Devices For Control Reactive Power’S Consumption Of Asynchronous Motor, Ilkhomjon Khakimovich Siddikov, Dilyorbek Karimjonov Doniyorbek O'G'Li -, Abdumutal Abdikarimovich Abdigapirov

Chemical Technology, Control and Management

In the article given materials of developing of three-phase electromagnetic current transducers of reactive power, using with asynchronous motor, methods connecting of two sensing element, series, parallel and differential and loops suitable for each phase, dynamic characteristics of output signals of three-phase electromagnetic current transducers asynchronous motor.

On the basis of modern calculation and design complexes are of great importance in the research variable sizes of three-phase current electromagnetic transducers of filter-compensation devices of reactive power of asynchronous motors. Presented mathematical model of research of electrical, electromagnetic and magnetic elements of electromagnetic current transducers in the …

Modeling Of The Process Of Measuring Conversion Of The Flow Of Liquid And Gaseous Media By The Method Of Variable Pressure Drop, Shukhrat Manapovich Gulyamov, Elbek Elmirza O'G'Li Ortiqov

Chemical Technology, Control and Management

On the basis of material and heat balances, taking into account the initial and boundary conditions, a mathematical model of the process of measuring the transformation of liquid and gaseous technological media by the method of variable pressure drop is constructed. The analysis of the results of studying the influence of non-stationary flows of a controlled medium on the uncertainty of the results of measuring the flow rate of liquids and gaseous mixtures with a changing hydrodynamic structure of the flow of a controlled medium is performed. A comparative analysis of the calculated and experimental transient processes in the measuring …

Virtual Potassium Chloride Analyzer In The System Of Advanced Control Of Potash Fertilizer Production Processes, Umidjon Ruziev, Jahongir Sherboyevich Bekqulov

Chemical Technology, Control and Management

It is proposed to include virtual instrumental quality analyzers of potash fertilizers in the composition of the advanced (advanced) management system. The structure of the virtual analyzer is substantiated using mathematical models of the technological process of drying potassium chloride in its composition. Based on the results of fuzzy clustering, the parameters of the modes of the technological process of drying potassium chloride are determined.

Influence Of Magnetomechanical Properties Of Ferromagnetic Materials On The Sensitivity Of A Magnetoelastic Sensor, Sulton Amirov, Kamila Komilovna Jurayeva

Chemical Technology, Control and Management

The requirements of high operational reliability are most fully met by automated monitoring and control systems, the elements of which are magnetoelastic sensors. Such sensors, due to their metrological characteristics, have found application in electrified railway transport, in the metallurgical, metalworking, mining and other industries. The principle of operation of such sensors is based on the fact that in the process of influencing the magnetic core of the sensor by force, there is a change in the magnetic permeability of the material, a change in the magnetic resistance of the circuit, a change in the mutual inductance coefficient of the …

Algorithmic Methods For Developing The Structure Of A Thyristor Electric Drive For Mining Machines, N.R Yusupbekov, O.A. Jumaev, S.S. Turaev

Chemical Technology, Control and Management

The article discusses the creation of algorithmic structures and the development of digital control systems for electric drives of mine-lifting machines, provides some concepts for creating digital control systems using thyristor converters. The analysis of the static volt-ampere characteristics of the thyristor is given, some calculations of the circuits and circuits of the thyristor converter (TP) corresponding to the different modes of operation of the TP are given, and also, based on the synthesis of the dynamic properties and characteristics of the thyristor, an algorithmic structure of the model of the thyristor converter is proposed.

Algorithms For Multi-Factory Polynomial Modeling Of Technological Processes, Farrukh Do'stmirzayevich Jo'rayev, Murodjon Ashurqulovich Ochilov

Chemical Technology, Control and Management

The article reveals the meaning and essence of the modeling method in the study of complex technological processes based on the problematic aspects of building multifactorial relationships and the principles for their elimination. In the case of non-linearity of multifactorial connections of a complex system, the expediency of approximating such functions by polynomials is substantiated. The authors' ideas about the increasing importance of interpolation methods in practice against the background of the possibility of simplification based on the use of modern mathematical hardware and software for integration into the process of modeling and optimizing technological processes due to the complexity …