Dielectric Permittivity Of Pzt 95/5 Ferroelectric Ceramics And 0.27pin-Pmn-0.26pt Single Crystals Under Pulsed High Electric Fields,
2024
Missouri University of Science and Technology
Dielectric Permittivity Of Pzt 95/5 Ferroelectric Ceramics And 0.27pin-Pmn-0.26pt Single Crystals Under Pulsed High Electric Fields, Sergey I. Shkuratov, Jason Baird, Vladimir G. Antipov, Christopher S. Lynch
Mining Engineering Faculty Research & Creative Works
The dependence of the dielectric permittivity of ferroelectric materials on electric field magnitude impacts the performance of ferroelectric devices. In a ferroelectric generator, a shock wave travels through the ferroelectric element and depolarizes it, and surface charges are released from the element electrodes, resulting in the generation of a megawatt power level for several microseconds. The dielectric properties of the compressed and uncompressed zones of the ferroelectric element affect the generated voltage and energy. The results of previous studies indicate that the low-field dielectric permittivity of poled Pb0.99(Zr0.95Ti0.05)0.98Nb0.02O3 (PZT 95/5) ferroelectrics in the uncompressed zone differs significantly from the high-field …
Suitability Of The Height Above Nearest Drainage (Hand) Model For Flood Inundation Mapping In Data-Scarce Regions: A Comparative Analysis With Hydrodynamic Models,
2024
School of Engineering
Suitability Of The Height Above Nearest Drainage (Hand) Model For Flood Inundation Mapping In Data-Scarce Regions: A Comparative Analysis With Hydrodynamic Models, Navin Tony Thalakkottukara, Jobin Thomas, Melanie Watkins, Benjamin C. Holland, Thomas Oommen, Himanshu Grover
Michigan Tech Publications
Unprecedented floods from extreme rainfall events worldwide emphasize the need for flood inundation mapping for floodplain management and risk reduction. Access to flood inundation maps and risk evaluation tools remains challenging in most parts of the world, particularly in rural regions, leading to decreased flood resilience. The use of hydraulic and hydrodynamic models in rural areas has been hindered by excessive data and computational requirements. In this study, we mapped the flood inundation in Huron Creek watershed, Michigan, USA for an extreme rainfall event (1000-year return period) that occurred in 2018 (Father’s Day Flood) using the Height Above Nearest Drainage …
The Valuation Of Exit Option In A Lignite Mine Using Monte Carlo Simulation,
2024
University of Szczecin, Department of Banking and Finance, Poland
The Valuation Of Exit Option In A Lignite Mine Using Monte Carlo Simulation, Marcin Pawlak, Tomasz Wiśniewski
Journal of Sustainable Mining
This study aims to demonstrate the application of simulation techniques to the valuation of real options. The nature of the paper is methodological and empirical. The purpose of the valuation of the option to close a lignite mine in Poland is to demonstrate the methodology and advantages of employing Monte Carlo simulation in the valuation of real options. Close to actual numerical data reveals a complex optimization problem in the context of strategy selection by decision-makers. Numerous factors (extraction costs, reclamation costs, the write-off for the reclamation fund, etc.), their interpenetration and multilevel influence on the decision to close the …
Mathematical Model For The Management Of The Wave Processes In Three-Winding Transformers With Consideration Of The Main Magnetic Flux In Mining Industry,
2024
Lviv Polytechnic National University, 79013, L'vov, Stepana Bandera st., 12, Ukraine
Mathematical Model For The Management Of The Wave Processes In Three-Winding Transformers With Consideration Of The Main Magnetic Flux In Mining Industry, M. S. Seheda, O. S. Beshta, P. F. Gogolyuk, Yu. V. Blyznak, R. D. Dychkovskyi, A. Smoliński
Journal of Sustainable Mining
The aim of the work is to study the wave processes in three-winding power transformers caused by impulse overvoltage, to create an improved mathematical model for reproducing the process of distribution and transmission of the impulse in the windings of a three-winding power transformer. A mathematical model has been developed for the study of internal overvoltage in the windings of three-winding power transformers, based on the proposed substitute circuit of an infinitesimal element, taking into account the longitudinal and transverse inductive connections between the turns of the winding, the electromagnetic connections between the windings and the flux splitting from the …
The Effect Of Blasting Using Low-Density Emulsion Explosives,
2024
Faculty of Mining, Geology and Petroleum Engineering, Department of Mining Engineering and Geotechnical Engineering, University of Zagreb, Pierottijeva 6, 10000, Zagreb, Croatia
The Effect Of Blasting Using Low-Density Emulsion Explosives, Vinko Škrlec, Mario Dobrilović, Barbara Štimac Tumara, Vječislav Bohanek
Journal of Sustainable Mining
Low-density emulsion explosives are essentially blends of an emulsion matrix and a certain amount of gaseous phase inclusions acting as hot spots. With the addition of expanded polystyrene for gaseous sensibilization, the resulting explosive blend was developed to reduce peak values and pressure impulse of gaseous detonation products on surrounding rock. This resulted in a decrease in rock stress and a decrease in cracking zone width outside of the minefield boundary. The use of low-density emulsion explosives correlates with the decrease in the seismic effect of blasting, more precisely, the decrease of induced rock oscillation velocities. The low-density emulsion explosive …
Numerical Simulation On Effect Of Coal Pillar Width On Stability Of Retained Roadway: A Case Study Of Khe Cham Coal Mine, Vietnam,
2024
Faculty of Mining, Hanoi University of Mining and Geology, Vietnam
Numerical Simulation On Effect Of Coal Pillar Width On Stability Of Retained Roadway: A Case Study Of Khe Cham Coal Mine, Vietnam, Quang Phuc Le, Tien Dung Le
Journal of Sustainable Mining
When extracting coal seams in Vietnam underground mines, coal pillars are often left unmined for the protection of retained roadways in the longwall mining method. During longwall mining operations, coal pillars are often placed where high-stress concentrations occur in the abutment pressure zone of adjacent panels, especially when extracting seams under hard-to-cave main roof conditions. The instability of coal pillars under the loading of the main roof may cause the roadway to collapse, threatening the safe operation of a coal mine. This paper presents a detailed numerical investigation of the effect of coal pillar width on the stability of retained …
Investigating Detonation Parameters Through The Plate Dent Test: A Novel Approach For Characterizing Detonation Curvature And Thickness,
2024
Missouri University of Science and Technology
Investigating Detonation Parameters Through The Plate Dent Test: A Novel Approach For Characterizing Detonation Curvature And Thickness, Emily Michelle Johnson
Doctoral Dissertations
Detonation is the driving factor behind how an explosive, used in an array of applications, performs. Understanding and measuring detonation parameters of an explosive is key in explosive charge design and application. Currently, determining parameters is costly as the instrumentation needed is expensive in terms of price, maintenance, and personnel. This research examines two methods of determining detonation parameters through measurement of secondary material response to the detonation wave in an effort to provide an alternate, simple, and inexpensive method of measurement. The first of these studies focuses on the Gurney Model and demonstrates that the model's accuracy was diminished …
Pit Design And Mine Planning Of Nong Wa Sub-Basin, Sin Pun Coal Deposit, Southern Thailand,
2024
Faculty of Engineering
Pit Design And Mine Planning Of Nong Wa Sub-Basin, Sin Pun Coal Deposit, Southern Thailand, Gbenga Timilehin Adewumi
Chulalongkorn University Theses and Dissertations (Chula ETD)
Nong Wa is a sub-basin located within the Sin Pun coal deposit, which has no history of mining activities. This study focused on the planning and design of the sub-basin pit, potentially paving the way for future mining operations in the region. The objective of the research was to evaluate the economic viability of coal extraction and to develop an optimized pit to maximize resource recovery. To achieve this objective, a coal seam model of the deposit was created using advanced modeling software such as AutoCAD and MineSight. The seam model was used to design the ultimate pit, pushback, and …
Underground Blast Fragmentation Modeling For Use In The Mine-To-Mill Strategy,
2024
University of Kentucky
Underground Blast Fragmentation Modeling For Use In The Mine-To-Mill Strategy, Lauren Shields
Theses and Dissertations--Mining Engineering
More than 40 years ago, the mine-to-mill concept was introduced in the mining industry by establishing a relationship or link between processing and mining activities. To date, many successful case studies have documented the evident benefits of the mine-to-mill approach. In most cases, the basis of the mine-to-mill approach is to tailor the details of a blast design and its proper execution in order to satisfy specific mineral processing requirements downstream. Most of the available literature and case studies deal with surface mine operations. Due to the relative simplicity of surface mining, the relationship between the powder factor, defined as …
Enhance Effectiveness Of Monitoring Scheme Using Insar On Tailings Storage Facility No. 2, Chatree Gold Mine, Thailand,
2024
Faculty of Engineering
Enhance Effectiveness Of Monitoring Scheme Using Insar On Tailings Storage Facility No. 2, Chatree Gold Mine, Thailand, Shanghai Chea
Chulalongkorn University Theses and Dissertations (Chula ETD)
Tailings storage facility (TSF) is a critical component of the mining industry, serving to safely contain waste generated during mineral extraction. At Chatree Gold Mine, the largest and only active gold mine in Thailand, TSF No.2 handles approximately 5 million tons of tailings annually. Effective monitoring of the facility is crucial for hazard prevention and regulatory compliance. This study aims to enhance the monitoring scheme of TSF No.2 by employing Small Baseline Subset Interferometric Synthetic Aperture Radar (SBAS-InSAR) technique, processed via MintPy software, to analyze ground deformation. Despite traditional monitoring methods, such as in-situ geodetic surveying, offering valuable insights, they …
Recovery Of Tin From Kaolin Mine Tailing, Rangoon, Thailand,
2024
Faculty of Engineering
Recovery Of Tin From Kaolin Mine Tailing, Rangoon, Thailand, Archana Pandit
Chulalongkorn University Theses and Dissertations (Chula ETD)
This study investigates the recovery of tin from kaolin waste using gravity, electrostatic, and magnetic separation techniques. A total of 123.500 kg of sand and 103.200 kg of silt were processed using a shaking table, spiral concentrator, high-tension separator, induced roll magnetic separator, and Frantz magnetic separator. Mineralogical and chemical characterization was conducted using X-ray diffractometer (XRD), X-ray fluorescence (XRF), and microscopic analysis to determine tin distribution and occurrence. Experimental results showed that the silt fractions generally exhibited higher tin content than the sand fractions. In this study, Case A refers to the samples (Sand A and Silt A) processed …
Simulation On Acid Gas Removal From Natural Gas Processing With Membrane And Absorption Process,
2024
Faculty of Engineering
Simulation On Acid Gas Removal From Natural Gas Processing With Membrane And Absorption Process, Ratikorn Sornumpol
Chulalongkorn University Theses and Dissertations (Chula ETD)
The comparison using simulations of CO₂ removal from natural gas via membrane separation and monoethanolamine (MEA) absorption has been studied. The membrane model is applied with the single- and two-stage configurations over feed pressures 3,000–9,000 kPa, temperatures 10–59 °C, CO₂ concentrations 20–70 mol %, membrane areas 2,500–5,500 m², and flows 331,800–580,600 m³/h. At 10 °C feed temperature, CO₂ permeability is enhanced while CH₄ selectivity improves slightly, increasing CO₂ capture efficiency up to 74 % with only minor methane losses, though at the cost of higher refrigeration duty. The 10 °C operation also leads to stronger driving force across the membrane, …
The Methodology For Integrating Robotic Systems In Undeground Mining Machines,
2024
University of Kentucky
The Methodology For Integrating Robotic Systems In Undeground Mining Machines, Peter Kolapo
Theses and Dissertations--Mining Engineering
Roof bolting is a critical operation in ensuring the safety and stability of underground mines by securing the roof strata with bolts. The process involves moving and manipulating heavy tools while being vigilant about the safety of the area. During the installation of roof bolts, operators are exposed to hazardous conditions due to challenging working conditions in underground mines, extensive working hours, and demanding shift schedules leading to personnel fatigue and influencing operators to take shortcuts that may increase the risk of injuries and fatal accidents. The successful completion of roof bolting tasks depends heavily on operator judgment and experience …
Autonomous Shuttle Car Docking To A Continuous Miner Using Rgb-Depth Imagery,
2024
University of Kentucky
Autonomous Shuttle Car Docking To A Continuous Miner Using Rgb-Depth Imagery, Sky Rose
Theses and Dissertations--Mining Engineering
A great deal of research is currently being conducted in automating mining equipment to improve worker health and safety and increase mine productivity. Significant progress has been made in some applications, e.g., autonomous haul trucks for surface mining. However, little progress has been made in autonomous face haulage in underground room-and pillar coal mines. Accordingly, this thesis addresses automating the operation of a shuttle car, focusing on positioning the shuttle car under the continuous miner coal-discharge conveyor during cutting and loading operations. The approach uses a stereo depth camera as the sensor, and machine-learning algorithms are used to identify various …
Discrete Element Modeling To Predict Muckpile Profiles From Cast Blasting,
2024
University of Kentucky
Discrete Element Modeling To Predict Muckpile Profiles From Cast Blasting, Russell Lamont
Theses and Dissertations--Mining Engineering
Movement of overburden or ore from one location to another may be considered the primary physical process of mining. The means by which it is transported is then of primary concern both to economic production and cost control. The geologic characteristics of some mineral deposits, especially coal and phosphates, lend themselves to overburden transport by means of cast blasting, which when efficiently designed has proven itself to be a cheaper method than traditional truck/shovel, dragline, or even dozer push transport. Simultaneously, this movement of a significant portion of overburden using explosives may enable an operation to increase mineral production, as …
Prediction Of Final Subsidence Under Dipping Seam Conditions,
2024
University of Kentucky
Prediction Of Final Subsidence Under Dipping Seam Conditions, Ernesto Maldonado Esguerra
Theses and Dissertations--Mining Engineering
The prediction of ground movements due to underground coal mining and their impacts on the surface are essential considerations that numerous researchers worldwide have studied. Most of these studies have focused on developing different analytical and empirical models for predicting and calculating ground deformation indices for flat or gently dipping seams under variable topography. However, a few studies are available on predicting ground movements under dipping seam conditions. Although most inclined coal seams are in China, India, and a few other countries, dipping seam conditions have been encountered in some cases in the US, where the inclination (dip) may be …
Copper Ammoniacal Recycling Process Development For Leaching Electrolyte, Solvent Extraction, And Electrowinning,
2024
University of Kentucky
Copper Ammoniacal Recycling Process Development For Leaching Electrolyte, Solvent Extraction, And Electrowinning, Zulqarnain Ahmad Ali
Theses and Dissertations--Mining Engineering
Electronic waste (e-waste) encompasses waste originating from electronic and electrical equipment. In 2022, 59.4 million metric tons of e-waste were generated, projected to increase to 74.7 million metric tons by 2030. Among the most valuable components within E-Waste are the printed circuit boards (PCBs), primarily composed of metals including copper (Cu), gold (Au), silver (Ag), cobalt (Co), nickel (Ni), bismuth (Bi), and various other base and precious metals. Notably, copper is the predominant element in PCBs, with concentrations exceeding those in their respective ores. The high demand for copper driven by the ongoing push towards greener technologies and its abundant …
Characterization And Concentration Of Critical Minerals And Rare Earth Elements From Primary And Secondary Silicate Deposits,
2024
University of Kentucky
Characterization And Concentration Of Critical Minerals And Rare Earth Elements From Primary And Secondary Silicate Deposits, Muhammed Melih Elseyh
Theses and Dissertations--Mining Engineering
Critical materials (CMs) are crucial for sustainable energy. This investigation explored the extraction of rare earth elements (REEs) from the Halleck Creek deposit in Wyoming, and CMs from a construction sand deposit in Missouri. The Halleck Creek deposit is REE enriched (0.32%) as the mineral allanite within silicious host rock. Density fractionation tests revealed that 70% of the gangue can be rejected while recovering 90% of the REEs with an upgrading ratio of 4.5:1. By exploiting allanite’s paramagnetic properties, magnetic separations achieved a TREE upgrade ratio of 3:1 with 87% TREE recovery. Based on the density fractionation results, a rougher-scavenger-cleaner …
Cav-Ad: A Robust Framework For Detection Of Anomalous Data And Malicious Sensors In Cav Networks,
2024
Missouri University of Science and Technology
Cav-Ad: A Robust Framework For Detection Of Anomalous Data And Malicious Sensors In Cav Networks, Md Sazedur Rahman, Mohamed Elmahallawy, Sanjay Madria, Samuel Frimpong
Computer Science Faculty Research & Creative Works
The adoption of connected and automated vehicles (CAVs) has sparked considerable interest across diverse industries, including public transportation, underground mining, and agriculture sectors. However, CAVs' reliance on sensor readings makes them vulnerable to significant threats. Manipulating these readings can compromise CAV network security, posing serious risks for malicious activities. Although several anomaly detection (AD) approaches for CAV networks are proposed, they often fail to: i) detect multiple anomalies in specific sensor(s) with high accuracy or F1 score, and ii) identify the specific sensor being attacked. In response, this paper proposes a novel framework tailored to CAV networks, called CAV-AD, for …
Forecasting Of The Next Three (3) Decades Global Lithium Demand And Pricing Using Multivariate Stochastic Model.,
2024
Michigan Technological University
Forecasting Of The Next Three (3) Decades Global Lithium Demand And Pricing Using Multivariate Stochastic Model., Enoch Nii- Okai
Dissertations, Master's Theses and Master's Reports
The transition to electric vehicles (EVs) is pivotal in achieving global climate goals, with nations aiming to integrate a significant portion of new passenger vehicles as electric by 2030. This shift towards electric mobility includes a notable rise in battery-electric, plug-in hybrid, and fuel-cell electric vehicles to curb carbon emissions and foster sustainable transportation. Central to this transition is the critical role of lithium, often referred to as the "white gold of the 21st century," in electric vehicle batteries, especially rechargeable lithium-ion batteries renowned for their high energy efficiency, density, and durability. While lithium has historically found extensive use across …
