Mining Engineering Commons^™

Recovery Of Phosphorus From Florida Phosphatic Waste Clay, Amir Eskanlou

Graduate Theses, Dissertations, and Problem Reports (ETD)

This MS thesis examines the recovery of phosphorus (P) from Florida waste clay (WC). A comprehensive literature review revealed that: (i)-The most important values being lost to WC are P and rare earth elements (REEs). For the recovery of these values from WC, two crucial attempts are the removal of extremely fine-sized clays, followed by the recovery of phosphate content, which can pave the path for the recovery of REEs; (ii)-Any scientific/ technological solution should, at the same time, be economically and environmentally attractive to the industry. As such, moving from mostly chemical separation processes to the primarily physical/ physicochemical …

Improving Real-Time Methane Monitoring In Longwall Coal Mines Through System Response Characterization Of A Multi-Nodal Methane Detection Network, Brian Philip Cappellini

Graduate Theses, Dissertations, and Problem Reports (ETD)

Machine automation and atmospheric monitoring are used by many industries to improve safety and productivity in the workplace. The underground Methane Watchdog System (MWS) is a multi-nodal network of sensors currently under development. The MWS aims to improve safety and productivity by introducing 10 compact sampling units designed to be easily integrated within the current roof support equipment of the mine. Each unit contains an array of sensors used to continuously monitor the environmental conditions which include methane concentration, temperature, pressure, and relative humidity. All MWS units report information back to a remote central processing hub (CPH) which collects nodal …

Calculation Of Real Evapotranspiration By The Application Of Metric Method On Landsat-8 Data, Ali Imanian, Majid Hashemi Tangestani, Adel Asadi, Mohammad Zare

Michigan Tech Publications, Part 1

In geological remote sensing approaches for estimating evapotranspiration, METRIC method is among the most modern and precise approaches that many positive experiments have been reported regarding its applicability. In this study, the value of actual evapotranspiration (ET) occurred in Marvdasht farmlands, Fars province, Iran, was calculated instantaneously (hourly) and daily (24 hours), at 24 April 2017 using METRIC method and Lansat-8 data. In order to accuracy assessment of the results, estimated values were compared to the values calculated with Penman Monteith method in places that covers by alfafa crop. Our observations showed that ET values obtained via METRIC model on …

Computational Intelligent Impact Force Modeling And Monitoring In Hislo Conditions For Maximizing Surface Mining Efficiency, Safety, And Health, Danish Ali

Doctoral Dissertations

"Shovel-truck systems are the most widely employed excavation and material handling systems for surface mining operations. During this process, a high-impact shovel loading operation (HISLO) produces large forces that cause extreme whole body vibrations (WBV) that can severely affect the safety and health of haul truck operators. Previously developed solutions have failed to produce satisfactory results as the vibrations at the truck operator seat still exceed the “Extremely Uncomfortable Limits”. This study was a novel effort in developing deep learning-based solution to the HISLO problem.

This research study developed a rigorous mathematical model and a 3D virtual simulation model to …

Evaluation Of Excavated Surface Irregularities And Hardness Of Mechanical Excavations And Their Relationship With Excavator Performance, Prosper Evaristus Akansah Ayawah

Doctoral Dissertations

"This research involved lab and numerical excavation of a clastic sedimentary rock (Roubidoux Sandstone) using a long-bladed disc cutter in a Linear Rock Cutting Machine (LCM) with the aim of establishing relationships between the cutting parameters, excavated surface parameters (underbreaks, overbreaks and hardness), and performance parameters (specific energy and cutting rate). Three-dimensional cutting forces were recorded during the linear cutting. A structured laser imaging system was used to image the excavated surfaces for the estimation of the irregularities (ridge volumes (RV) and overbreak volumes (OV)). The excavated surface hardness was measured using the N-type Schmidt hammer. The numerical simulation was …

Using Similitude Theory And Discrete Element Modeling To Understand The Effects Of Digging Parameters On Excavation Performance For Rubber Tire Loaders, Atta Ur Rehman

Doctoral Dissertations

"The large sizes of mining equipment pose challenges for analysis using experiments or simulation. While scaled physical and simulation models can address this challenge, no previous work has explored how similitude theory and modeling can provide valid analysis of large equipment such as rubber tire loaders. The objective of this research was to apply similitude theory and discrete element modeling (DEM) to study the effect of different digging parameters on the penetration and the draft on the buckets of rubber tire loaders. The work sought to (1) test the hypothesis that the geometry of a rubber tire loader bucket and …

Mining Haul Road Defect Detection -- Advancement In Automated Road Extent And Response Calibration For Improved Maintenance, Alexander David Douglas

Doctoral Dissertations

Mine haul roads degrade rapidly due to extremely heavy loads on sub optimal construction materials. This research tests two methods of defect detection to determine limitations to current technology: optical detection and vehicle vibration response. Optical defect detection was found to have the least significant limitations for surface defect detection and vehicle vibration response modeling has the least significant limitations for subsurface defects. This research proposes novel methods to eliminate the critical limitations of both technologies.

Unmanned Aerial Vehicles (UAV) equipped with GPS and a high-resolution camera is used to create a 3-D point cloud using a structure-from-motion algorithm. This …

Relating Detonation Parameters To The Detonation Synthesis Of Nanomaterials, Martin Langenderfer

Doctoral Dissertations

“This research investigates the physical and chemical processes that contribute to the detonation synthesis of silicon carbide nanoparticles. Bulk production of SiC nanoparticles through detonation is possible due to pressures achieved over 20 GPa and temperatures over 2000 K as well as quenching rates in excess of 13 billion K/second. These conditions catalyze reaction and bottom-up molecular growth while retaining particles < 100 nm in diameter. In this work, detonation synthesis of SiC was demonstrated by incorporation of polycarbosilane, an SiC precursor material, into an RDX/TNT explosive matrix prior to detonation. Detonation Synthesis of SiC was also accomplished by reacting elemental silicon with carbon liberated by the detonation of negatively oxygen balanced TNT. Hydrodynamic simulation of a 60:40 mass ratio RDX/TNT detonation created conditions thermodynamically suitable to produce cubic silicon carbide within the first 500 nanoseconds after the passage of the detonation wave while carbon remains chemically reactive for molecular formation. Simulations and experimental tests indicated that loading configuration and impedance mismatch of the precursor additives used in detonation synthesis results in conditions in the additives that exceed the accepted detonation pressure of the explosive by greater than three times. Finally, a full factorial experimental design showed increasing silicon concentration, reducing silicon size, and reducing oxygen balance by adjusting the ratio of RDX to TNT decreased the explosives detonation pressure by 20% and increased the soot yield and concentration of SiC observed in the detonation products by 82% and 442% respectively”--Abstract, page iv.

Investigation Of Anomalous Data Trends During Coal Dust Explosibilty Testing, Jacob Lee Miller

Doctoral Dissertations

Coal dust explosibility is a health and safety concern that has been a recognized hazard for over 100 years. Initial testing by the Author using a Siwek 20L apparatus recorded a secondary maximum pressure at higher dust concentrations (1,000-7,000g/m³) with Pulverized Pittsburgh Coal (PCC). Higher dust concentrations are beyond the typical ASTM E1226 testing procedure but are possible in mining and processing scenarios. No reference documents have been discovered that show a secondary maximum pressure at higher dust concentrations. Literature reviewed identified that once a coal dust concertation generates a peak pressure, the pressure remains constant or decreases …

Investigating The Focusing Effect Of Charge Geometry With Computer Simulations, Witness Plates, And High-Speed Videography, Kelly Ray Williams

Doctoral Dissertations

"Scaled distance is used to calculate a safe standoff radius from the detonation of a known mass of an explosive. It has been shown that varying only the geometry of the charge significantly overdrives regions of the blast wave potentially resulting in hazardous overpressure levels at scaled distance safe radii. Pressure transducers are used to measure overpressure surrounding spherical, cylindrical, and cubic charges to determine if bridge waves were formed at the edges between flat sides as seen in published studies of cylindrical charges. In the fireball field a witness plate is used to evaluate radial energy distribution with a …

Assessment Of Rib Failure Mechanisms Using Discontinuum Mechanics Based Modeling Approach, Maurice Nuonituo Sunkpal

Doctoral Dissertations

"Coal mine rib failures are major safety and health challenge for coal mines worldwide. The need for clear procedures to evaluate mine rib behavior and to provide an efficient, reliable, and consistent rib control protocol is needed. Understanding coal rib geomechanics is essential for improving rib stability and eliminating fatality and injury trends due to rib failures. This knowledge is also vital to determine support requirements.

The rib control practices used in the 21st Century in most countries originated in roof control techniques. Understandably, applying roof control methods to coal rib does not yield desirable results. The geology of structures …

Evaluation Of Various Separation Techniques For The Removal Of Actinides From A Rare Earth-Containing Solution Generated From Coarse Coal Refuse, Deniz Talan

Graduate Theses, Dissertations, and Problem Reports (ETD)

Rare earth elements have emerged as a vital commodity due to their significance in the production of high-tech devices as well as their utilization in defense and military systems. They are deemed critical due to potential scarcity, supply constraints, and the lack of minable concentrations. Therefore, alternative sources are needed to meet the demand and continue manufacturing rare earth-required products. Coal and coal by-products, in that regard, have presented a significant opportunity and proven to contain a considerable amount of rare earths. However, toxic elements such as thorium and uranium are frequently seen in the same mineralization as rare earths. …

Effect Of Spectral Bandwidths On Linear Feature Extraction: An Evaluation Of Landsat Etm+ And Oli Sensors, Ali Imanian, Adel Asadi, Majid Hashemi Tangestani, Saeid Homayouni, Ali Faghih

Michigan Tech Publications, Part 1

Hitherto there have been many studies comparing the usefulness of OLI and ETM+ sensors for linear feature extraction. However, not too much attention has been paid to the differences in the bandwidth of the two sensors. In this study, the suitability of Landsat ETM+ and OLI sensors for automatic detection of linear features by LINE algorithm was compared. In this study, eight regions in northern, central and southern parts of Iran were selected based on the diversity of lithology, the pristine status, and lack of human activities for the comparison of the two datasets. Results revealed that LINE algorithm performed …

Downhole Water Drainage From A Gas Reservoir For Water Dumpflood In An Underlying Oil Reservoir, Htet Myet Zin Naing

Chulalongkorn University Theses and Dissertations (Chula ETD)

For wells drilled in a bottom water-drive gas reservoir, water coning may lead to a considerable amount of water production which diminishes the gas recovery. If the gas reservoir has an oil reservoir underneath, a method called “Downhole Water Drain for Water Dumpflood” (DWDDF) can be performed to drain water from the aquifer underneath the gas reservoir and dump it into the oil reservoir to perform waterflooding. DWDDF technique can help increase gas production from the upper gas reservoir and oil production from the lower reservoir at the same time. In this study, a simple reservoir model having common rock …

Quality Control Of Chemical Grade Calcium Carbonate From Lopburi Limestone Deposit In Thailand, Pimpichcha Teawpanich

Chulalongkorn University Theses and Dissertations (Chula ETD)

Calcium carbonate (CaCO3) is naturally produced from calcite, limestone, chalk, and marble. It is being used as raw material in various industries (e.g., cement, plastic, paint, paper, and pharmaceutical industries). The low-grade CaCO3 samples obtained from a calcite plant at Khoktum Sub-district, Muang Lopburi District, Lopburi Province, Thailand were used in this study. These samples contain more than 98% of CaCO3 while Fe2O3 contents are higher than 0.1% and increased after finished the process. Because of this problem, the products could not be sold since lower Fe2O3 contents are required (e.g., ≤0.05% for filler grade and ≤ 0.1% for animal …

Effects Of Clay Minerals On Oil Recovery Mechanism In Low Salinity Waterflooding In Shaly-Sandstone Formation, Tri Yudha Putra

Chulalongkorn University Theses and Dissertations (Chula ETD)

Low Salinity Waterflooding (LSWF) is one of Enhanced Oil Recovery (EOR) techniques that are often mentioned nowadays. Several studies showed that injecting low salinity water leads to Multi-component Ion Exchange (MIE) which is one of oil recovery mechanisms provided by this technique. This study was performed to investigate the effects of specific clay mineral in rock and ion in injected water. First, representative clays were analytically tested to ensure their mineral compositions and the selected representative clays were tested by filtration with different water formulations to identify ionic capacities in MIE for each clay. Results obtained from filtration test and …

Evaluation Of Lidar Systems For Rock Mass Discontinuity Identification In Underground Stone Mines From 3d Point Cloud Data, Mario Alejandro Bendezu De La Cruz

Graduate Theses, Dissertations, and Problem Reports (ETD)

The goal of this thesis is to compare the accuracy and precision of the discontinuity identification results obtained by three active remote sensing technologies along with a point cloud processing program, and the results obtained by conventional methods. For this research, the active remote sensing devices were terrestrial LIDAR, mobile LiDAR with Simultaneous localization, and mapping (SLAM), and LIDAR/Camera on an autonomous UAV. The open-source point cloud data processing programs Discontinuity Set Extractor (DSE) and the Cloud Compare were used to process point cloud data.

The results of this research found that it is possible to identify certain geological structures …

Implementing The Empirical Stone Mine Pillar Strength Equation Into The Boundary Element Method Software Lamodel, Samuel Escobar

Graduate Theses, Dissertations, and Problem Reports (ETD)

In this research, the equation for the increasing stress into the interior of a stone mine pillar, as a function of the pillar width-to-height ratio, is derived from the empirical pillar strength equation proposed by Esterhuizen et al. (2011). The gradient stress equations for the stone mine pillars were derived by following similar approaches to those presented by Mark et al. (1992) and Johnson et al. (2014). In these approaches, it is assumed that the variation of stresses within the pillar is a function of distance to the closest rib. The stress gradient function provides the stress distribution within the …

Optimization Of Operating Conditions And Design Parameters On Coal Ultra-Fine Grinding Through Kinetic Stirred Mill Tests And Numerical Modeling, Francisco Patino

Graduate Theses, Dissertations, and Problem Reports (ETD)

This study investigated the ultra-fine coal grinding performance of four low- to moderate-cost grinding media: ceramic balls, granular sand, alumina beads, and silica beads. The kinetic grinding tests were conducted using a stirred mill, while different operating conditions, including the media size, solids concentration, and the addition of viscosity modifiers, were examined. Characterization studies in terms of particle size, shape, and surface morphology were further performed to support the experimental findings. Moreover, using population balance modeling, grinding simulation was performed in Matlab to forecast the particle size distribution based on the specific energy input and experimental size-related data. The results …

Geology Oriented Loading Approach For Underground Coal Mines, Deniz Tuncay

Graduate Theses, Dissertations, and Problem Reports (ETD)

Mining-induced stresses in underground coal mines play a significant role in pillar and support design, hence in the safety of mining operations. Adequate design of pillars and roof control plans rely on the accurate assessment of the mining-induced loads, as well as the load-bearing capacities of the supports. In pillar design tools frequently used by the underground coal mining industry and Mine Safety and Health Administration (MSHA), overburden loading is estimated by geometric concepts such as the tributary area and the abutment angle method. These methods do not explicitly consider important mechanical responses such as specific overall ground behavior. The …