Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 5 of 5
Full-Text Articles in Service Learning
Design And Control Of A Peristaltic Pump To Simulate Left Atrial Pressure In A Conductive Silicone Model, Jeremy Collins
Design And Control Of A Peristaltic Pump To Simulate Left Atrial Pressure In A Conductive Silicone Model, Jeremy Collins
Mechanical Engineering Undergraduate Honors Theses
According to the CDC, atrial fibrillation is responsible for more than 454,000 hospitalizations and approximately 158,000 deaths per year. A common treatment for atrial fibrillation is catheter ablation, a process in which a long flexible tube is guided through the femoral artery and to the source of arrhythmia in the heart, where it measures the electrical potential at various locations and converts problematic heart tissue to scar tissue via ablation. This paper details the design and control of a low-cost ($400) peristaltic pump system using repetitive control to replicate blood pressure in the left atrium in a conductive silicone model …
Thermal Testing And Characterization Of Nanoparticles Synthesized For Biological Treatment, Tonie Butler
Thermal Testing And Characterization Of Nanoparticles Synthesized For Biological Treatment, Tonie Butler
Mechanical Engineering Undergraduate Honors Theses
The overall goal of this research project is to synthesize iron core, silica capped nanoparticles that, when they are exposed to a particular magnetic field, will react by increasing in temperature and emitting substantial thermal output. They will be injected into the human body for biological benefit by targeted thermal radiation. Once in the human body, ideally, they will be able to target a specific area, and then a magnetic field will be applied to induce thermal output through the process of hyperthermia. As the nanoparticles emit heat, they will mimic the natural bodily behavior seen by way of hyperthermia, …
Development Of An Integrated Salt Cartridge-Reverse Electrodialysis (Red) Device To Increase Electrolyte Concentrations Of Human Blood Flow To Power Biomedical Devices, Caroline Campbell
Development Of An Integrated Salt Cartridge-Reverse Electrodialysis (Red) Device To Increase Electrolyte Concentrations Of Human Blood Flow To Power Biomedical Devices, Caroline Campbell
Chemical Engineering Undergraduate Honors Theses
Emerging technologies in nanotechnology and biomedical sciences have led to an increase in biomedical implantable devices including cardiac pacemakers, artificial organs, drug pumps, and sensors. These devices require continuous stable and reliable power to operate, which creates the demand for the need to find a safe, reliable, and stable power source. A promising avenue for a power source for these devices is a miniaturized reverse electrodialysis (RED) biopower cell design that utilizes the salinity differences between bloodstreams that flow inside the human body. Initial results of the RED system demonstrate that higher gradient salinity differences between streams lead to a …
Economic Feasibility Of Mixed Plastic Waste Pyrolysis Using Twin Reactor System In Northwest Arkansas, Carol Rogers, Patricia Means, Renato Gonzalez, Kaida Sheets, Hayden Townsend
Economic Feasibility Of Mixed Plastic Waste Pyrolysis Using Twin Reactor System In Northwest Arkansas, Carol Rogers, Patricia Means, Renato Gonzalez, Kaida Sheets, Hayden Townsend
Chemical Engineering Undergraduate Honors Theses
Plastic waste generation is increasing at an unsustainable rate while recycling solutions remain stagnant. As a chemical means of recycling, mixed plastic waste pyrolysis can generate synthetic oil appropriate for use as fuel in power generation from plastic waste that otherwise accumulates in landfills. With the scaling of a commercial plastic pyrolysis process in Northwest Arkansas (NWA) modeled after an operational sawdust pyrolysis unit in Huntsville, Arkansas, economic analysis resulted in 26.3% internal rate of return. Therefore, construction of a commercial mixed plastic-to-fuel pyrolysis plant is economically justified and should be pursued. To effectively implement the proposed design, NWA must …
Designing Cryogenic Strain Device For 2d Materials, Jake Carter
Designing Cryogenic Strain Device For 2d Materials, Jake Carter
Mechanical Engineering Undergraduate Honors Theses
The Churchill lab working within the Physics Department at the University of Arkansas is working to create important quantum states including weak topological insulators (TIs) through the use of symmetry engineering and topological electronic states in two-dimensional (2D) crystals of WHM materials. Experimental results of these topological states have been obstructed due to the difficulty to perform controlled in situ strain. This project strives to create a mount to utilize a piezoelectric nanopositioner within cryostats achieving an in situ strain that creates the quantum states the lab is looking to observe. This report also examines the necessary equations to determine …