Geophysics and Seismology Commons^™

Simulation Of Wave Propagation In Granular Particles Using A Discrete Element Model, Syed Tahmid Hussan

Electronic Theses and Dissertations

The understanding of Bender Element mechanism and utilization of Particle Flow Code (PFC) to simulate the seismic wave behavior is important to test the dynamic behavior of soil particles. Both discrete and finite element methods can be used to simulate wave behavior. However, Discrete Element Method (DEM) is mostly suitable, as the micro scaled soil particle cannot be fully considered as continuous specimen like a piece of rod or aluminum. Recently DEM has been widely used to study mechanical properties of soils at particle level considering the particles as balls. This study represents a comparative analysis of Voigt and Best …

Evaluating The Feasibility Of Using Strain Measured During Sinusoidal Rate Pumping Tests To Characterize An Aquifer, Riley Blais

All Theses

Pumping tests with sinusoidal variation in pumping rate have been proposed as a method for improving aquifer characterization. These tests can interrogate a larger aquifer volume than slug tests and they can be more sensitive to small variations in drawdown. Current methods of using sinusoidal variations of rate are based on measuring pressure signals from the reservoir or aquifer, which requires access to monitoring wells. An alternative approach has been developed that measures the strain in the vadose zone instead of pressure in the reservoir. An instrument has been developed at Clemson University that can measure small strains using optical …

Cascadia Subduction Zone Earthquake Vertical Ground Acceleration Investigation And Potential Impact On Bridges In The Pacific Northwest, Rachel Caroline Bassil

Civil and Environmental Engineering Master's Project Reports

The effects of vertical ground accelerations during subduction zone earthquakes currently are not sufficiently understood. There are numerous case studies and evidence that effects of vertical ground accelerations can significantly impact the performance of bridges during a seismic event, but most previous research has been focused on shallow crustal earthquakes. Current bridge design codes provide little guidance for accounting for vertical ground accelerations in seismic design, in part because additional information is needed about the characteristics of vertical ground motions during Cascadia Subduction Zone (CSZ) earthquakes in the Pacific Northwest.

For this study, recorded seismic data from recent subduction zone …

Development Of Deep Shear Wave Velocity Profiles And An Approach To Generate Site Signature Consistent Pseudo Shear Wave Velocity Profiles In The Mississippi Embayment, Ashraf Kamal Himel

Graduate Theses and Dissertations

This dissertation details the development of a surface wave method (SWM) technique to generate deep shear wave velocity profiles (VS profiles), applying this technique at 24 sites across the Mississippi embayment and developing an approach to generate pseudo site signature consistent VS profiles from velocity functions and fundamental frequency. In the presented SWM technique, active and passive source surface wave measurements are inverted along with fundamental frequency to develop a site signature consistent VS profile. Multiple transformation methods, including MSPAC, HRFK and FK are used to resolve experimental dispersion data from surface wave measurements. SWM VS profile at the Central …

Characterization Of Landslide Processes From Radar Remote Sensing And Hydromechanical Modeling, Yuankun Xu

Earth Sciences Theses and Dissertations

Landsides are a natural geomorphic process yet a dangerous hazard which annually causes thousands of casualties and billions of property loss in a global scale. Understanding landslide motion kinematics from early initiation to final deposition is critical for monitoring, assessing, and forecasting landslide movement in order to mitigate their hazards. Landslides occur under diverse environmental settings and appear in variable types; however, all types of landslides can be mechanically attributed to shearing failure at the basal surface due to stress regime shift contributed by internal and/or external forcing. Typical internal factors include soil/rock weathering, whereas typical external triggering forces encompass …

Shallow 3d Shear Wave Velocity Model And Revised Site Period Prediction Map For The Mexico City Basin, Rendon Martin Rieth

Graduate Theses and Dissertations

The goal of this study was to revise the existing site period prediction map and to develop a shallow 3D shear wave velocity model of the Mexico City Basin. To accomplish this goal, an extensive literature review was performed to compile as much pertinent shear wave velocity and site period data for the region. In total, 75 sites were used to revise the site period prediction map and 40 sites were used to develop the shear wave velocity model. The 2004 Complementary Technical Standards of Mexico site period prediction map was adjusted with new site period measurements across the basin …

Geophysical Techniques Used For The Analysis And Prediction Of Soil Strength And Mechanical Behavior, Matthew A. Hurley

Theses and Dissertations--Civil Engineering

Determining soil properties involves extensive laboratory testing of samples at discrete timing and location. Non-destructive analysis methods, such as electrical and seismic, presents alternatives to means of gathering soil properties accompanied with increased flexibility due to spatial and temporal applications. This research examined the ability of seismic wave data to predict soil behavior such as stress-strain and pore pressures using a modified version of Duncan and Chang (1970). Friction angle predictions were also analyzed using shear wave velocity and a modified form of the Santos and Gomez-Correria (2001) equation. This research also analyzed the use of electrical data to predict …

Geomechanical, Geochemical, And Hydrological Aspects Of Co2 Injection Into Saline Reservoirs, Maziar Foroutan

Graduate College Dissertations and Theses

Carbon dioxide Capturing, and Sequestration (CCS) is a promising technique that helps mitigate the amount of CO2 emitted into the atmosphere. CCS process mainly involves capturing CO2 at the industrial plant, followed by transportation and injection into a suitable geological storage, under supercritical conditions. Saline aquifers are among the best geological storage candidates due to their availability, high storage capacity and injectivity. Despite the CCUS technology promise, several public safety concerns remain to be address, including but not limited to reservoir/wellbore stability and integrity, CO2 leakage, ground deformation (uplift) and induced seismicity.

The injected supercritical CO2 is trapped through different …

Seismic Loading Effects Within Orthogonally Connected Steel Lateral Force Resisting Systems, Alhussin Faraj Aliwan

Graduate Theses and Dissertations

Steel buildings located within seismically active regions require special design considerations to ensure public safety and prevent collapse during an extreme seismic event. Two commonly used steel systems are special moment frames (SMFs) and buckling-restrained braced frames (BRBFs). When two seismic systems share a common column in an orthogonal configuration (such as at a building corner), design specifications currently consider a 100+30 rule wherein the shared column is designed for 100% fuse demand in one direction, plus 30% fuse demand from the other direction. While this rule has been shown to be reasonable for elastic building response, a few studies …

Stress-State And Injection-Rate Dependent Damage Processes During The Hydraulic Fracturing Of Granite, Gayani Sasendrika Gunarathna

Dissertations

Hydraulic fracturing is a well-stimulation technique that is employed in field applications, such as enhanced geothermal systems (EGS) and shale oil/gas extraction. This research experimentally investigates the effect of the state of stress and injection rate on the hydraulic fracturing processes. In addition, a displacement discontinuity method (DDM) code, FROCK, is used to model the crack initiation and propagation in a granite specimen under hydraulic fracturing conditions. In order to conduct the experimental work, a test setup capable of applying a triaxial state of stress and water pressure inside pre-fabricated flaws cut in prismatic granite specimens is developed. Additionally, the …

On The Seismic Performance Of Skewed Special Moment Frame Reduced Beam Section Connections, Damaso Daniel Dominguez

Graduate Theses and Dissertations

Special Moment Frames (SMFs) are frequently used in high seismic areas for architecturally constrained designs, as they provide lateral system stiffness without the use of braces which often obstruct views and architectural features. Reduced beam section (RBS) connections are popular SMF connection details developed following the Northridge earthquake to limit brittle fractures within connection welds. Current American Institute of Steel Construction (ASIC) provisions (i.e. AISC 341-16) provide prequalified SMF RBS connection details (including welding requirements); however, all prequalified details only consider orthogonal connections between the beam and column. This dissertation investigates the effect of adding skew within SMF RBS connections …

Development Of Vs Profiles And Site Periods In The Mexico City Basin, Landon Joel Woodfield

Graduate Theses and Dissertations

This study presents dynamic site characterization measurements at 25 sites within the Mexico City Basin. The primary focus of the testing was along the western edge of the Mexico City Basin. At each site, active source Multi-channel Analysis of Surface Waves (MASW) arrays and passive source Microtremor Array Measurements (MAM) L-arrays and circular arrays were used to acquire dispersion data. Horizontal to Vertical Spectral Ratio (HVSR) data was collected to determine site periods at each location. These experimental dispersion data and site periods were fit using a joint inversion of Rayleigh and Love wave dispersion data and HVSR site period …

Nanoindentation Characterization Of Elastic Properties Of Shales And Swelling Clay Minerals, Shengmin Luo

Doctoral Dissertations

Oil and gas shales are a class of multiscale, multiphase, hybrid inorganic-organic sedimentary rocks that consist of a generally uniform, preferentially oriented clay matrix with randomly embedded silt and sand particles as solid inclusions. A thorough understanding of the mechanical properties of shales is crucial for the exploration and production of oil and gas in the unconventional shale reservoirs, but it can be a challenging task due to their nature of compositional heterogeneity and microstructural anisotropy. In efforts to better characterize the mechanical properties of shales across different length scales and to fundamentally understand the laws of upscaling from individual …

Incorporating Geophysical Data In Slope Stability Modeling For Two Slopes In Arkansas, Vanessa Lebow

Graduate Theses and Dissertations

Slope failures in the United States alone cause millions of dollars in damage to infrastructure, threaten national monuments, create environmental hazards, and take an average of 25-50 lives a year. With the inevitable construction that occurs on slopes, it is imperative that the slopes be properly designed which requires a thorough understanding of slope grade, subsurface soil conditions, soil strength parameters, water table locations, and depth to bedrock across the entire site. The preferred method of data collection would be to use borings and other in-situ methods; however, sometimes due to cost constraints or site accessibility only a very limited …

The Effect Of Stiffness Anisotropy Of A Glacial Clay On The Behaviour Of A Shallow Wind Turbine Foundation, Jesús A. González-Hurtado

Electronic Thesis and Dissertation Repository

Shallow wind turbine foundations are designed based on investigations of the ultimate, serviceability and fatigue limit states. The serviceability limit state design approaches in particular are based on simple isotropic elastic half-space analyses that ignore coupling between loading directions, and soil non-linearity and elastic anisotropy. Many of the wind farms in Ontario are constructed around the Great Lakes basin and a number of these areas are characterized as stiff clayey glacial tills. It is recognized that many of these glacial materials exhibit some degree of strength, stiffness and fabric anisotropy. This research aimed to characterize the anisotropic geotechnical properties of …

Effects Of Electro-Osmotic Consolidation Of Clays And Its Improvement Using Ion Exchange Membranes, Lucas Martin

Dissertations

Electro-osmosis is an established method of expediting consolidation of soft, saturated clayey soils compared to commonly used methods, such as preloading with wick drains. In electro-osmotic consolidation a direct current (DC) is applied via inserted electrodes. This causes hydrated ions in the interstitial fluid to migrate to oppositely charged electrodes. Because the clay particles have a negative surface charge, the majority of ions in the interstitial fluid are positively charged. Therefore, the net flow will be towards the negatively charged electrode (cathode), where the water can be removed and thus consolidation is achieved. Certain problems, such as pH changes in …

Coupled Thermal-Hydrological-Mechanical-Chemical Processes In Geothermal And Shale Energy Developments, Arash Kamali-Asl

Graduate College Dissertations and Theses

Coupled Thermal-Hydrological-Mechanical-Chemical (THMC) processes that exist in the development of different geo-resources (e.g. deep geothermal and shale gas) affect the fracture response (i.e. aperture and permeability), which in turn influences the reservoir production. The main goal of this study was to experimentally evaluate the impact of THMC processes on the response of rock specimens relevant for deep geothermal and shale gas formations. The effects of THMC processes were investigated on: (i) success of the hydraulic fracturing/hydro-shearing mechanism during stimulation stage, and (ii) closure of the created network of fractures during production stage.

The elastic, cyclic, creep, and failure characteristics of …

Utilizing The Hvsr Second Peak For Surface Wave Inversions In The Mississippi Embayment, Ashraf Kamal Himel

Graduate Theses and Dissertations

Ambient noise data from 24 sites within the Mississippi Embayment were analyzed to estimate the fundamental frequency using the horizontal to vertical spectral ratio (HVSR) method. The fundamental frequency ranged from 0.17 to 3.43 Hz for the tested sites. At seventeen of the sites, a second higher frequency HVSR peak, which ranged from 0.617 Hz to 2.154 Hz, was observed in addition to the fundamental HVSR peak. The second peak frequency in the HVSR curve has been attributed by previous researchers as either an odd harmonic of the fundamental peak or a shallow impedance contrast from the Memphis sand layer …

Robust Earthquake Site Classification Assessment At Ontario Bridge Sites., Alex Bilson Darko

Electronic Thesis and Dissertation Repository

Canadian seismic design guidelines classify subsurface ground conditions based on the average shear-wave velocity (V_S) of the upper 30 meters (V_S30). We seek to optimize a robust earthquake site classification procedure for Ontario bridge sites, assessed primarily from blind comparison of non-invasive V_S depth profiling techniques. Non-invasive seismic testing is performed at 10 bridge sites in southern Ontario co-located with invasive penetration and/or borehole V_S measurements. Non-invasive surface wave dispersion and site amplification functions are jointly inverted to retrieve V_S profiles at each site. A general correlation between corrected V_S and cone …

Liquefaction-Induced Dragload And/Or Downdrag On Deep Foundations Within The New Madrid Seismic Zone, Ishimwe Elvis

Graduate Theses and Dissertations

Deep foundation elements are typically used to transfer structural loads for multi-story buildings and large-span bridges to a competent soil layer when 1) the soil close to the ground surface has no sufficient bearing capacity, and when 2) liquefiable soils are encountered. The majority of the bridges constructed within seismic zones rely upon the stability of earthen embankments and deep foundation that are installed above or within liquefiable soil deposits. Despite large factor of safety values or different load and resistance factors being used to adequately design deep foundations within seismic areas, soil liquefaction may cause extensive damage to the …

Back Calculation Of Intelligent Compaction Data For Mechanical Properties Of Soil System, Afshin Gholamy

Open Access Theses & Dissertations

For national economy, it is very important to have a reliable infrastructure. Because of this, all over the world, new roads are constantly being built and old roads are being maintained and, if necessary, expanded and/or repaired. Building a good quality road is very expensive, it costs several million dollars per kilometer. It is therefore crucial to make sure that the newly built and newly repaired roads are sufficiently stiff - so that they can withstand the predicted volume of traffic for a sufficient number of years. Current methods of estimating the stiffness are time-consuming and labor-consuming. The most accurate …

Onshore-Offshore Velocity Models North Of The Mendocino Triple Junction In Northern California, Alan Jacquez

Open Access Theses & Dissertations

The Mendocino Triple Junction (MTJ) marks the boundary where the Gorda plate, North American Plate, and Pacific Plate meet, separating the Cascadia subduction zone to the North from transform tectonics of the San Andreas plate boundary. This actively deforming region experiences high seismic activity and young geological features. Here we examine offshore and onshore seismic wide-angle reflection and refraction data north of the MTJ crossing the Cascadia subduction zone from offshore northern California to the Western edge of the Sierra Nevada. We image subsurface structures in this region by creating P-wave velocity models using datasets collected in 1993 to 1994 …

Hydrologic Monitoring And 2-D Electrical Resistivity Imaging For Joint Geophysical And Geotechnical Characterization Of Shallow Colluvial Landslides, Matthew M. Crawford

Theses and Dissertations--Earth and Environmental Sciences

Landslide characterization and hazard assessments require multidisciplinary approaches that connect geologic processes with geotechnical parameters. Field monitoring of hydrologic variables such as water content and water potential, coupled with geoelectrical measurements that can establish relationships used for geotechnical and landslide hazard investigations is deficient.

This study brings together different techniques to develop a methodology that connects geoelectrical measurements and shear strength. A field-based framework was established that includes (1) analysis of long-term soil moisture fluctuations within different landslides (2) establishment of constitutive and new equations that test the use of electrical conductivity to predict soil-water relationships and shear strength (3) …

Imaging The Subsurface In Eastern Part Of Lake Chesterfield Using A Combination Of Geophysical Tools, Jiawei Li

Masters Theses

"The Lake Chesterfield North Dam in Wildwood city, Missouri has been leaking, more or less continuously since the dam was constructed in 1986 despite mitigation efforts in 1988, 1994, 1995, 2004, and 2005. Neither the grouting efforts in 1988, 1994, 1995, 2004 or 2005, nor the placement and rehabilitation of an impervious clay liner in 2005 has solved the problem. Indeed, in June of 2017, the water level in Lake Chesterfield dropped at an alarmingly rapid rate.

Prior to authorizing additional mitigation work, the Lake Chesterfield Home Owners Association (LCHOA) decided to acquire geophysical data across the dry lake bed. …

Geophysical Delineation Of Megaporosity And Fluid Migration Pathways For Geohazard Characterization Within The Delaware Basin, Culberson County, Texas, Jonathan David Woodard

Electronic Theses and Dissertations

ABSTRACT

Differential dissolution of gypsum karst within the Delaware Basin poses a significant threat to infrastructure that society depends on. The study area is located in Culberson County, Texas and traverses a distance of approximately 54 kilometers along RM 652 within the Gypsum Plain which is situated on the northern margin of the Chihuahua Desert and includes outcrops of Castile and Rustler strata that host karst geohazards. Regions of karst geohazard potential have been physically surveyed proximal to the study area in evaporites throughout the Castile Formation outcrop; minimal hazards, in comparison to the Castile Formation, have been documented in …

Soil-Structure Interaction Effects On The Seismic Response Of Low-Rise Eccentrically Braced Frames, Luis Gerardo Buitrago Goyez

Graduate Theses and Dissertations

The importance of soil-structure interaction (SSI) effects on the seismic response of

buildings has been long recognized and has been researched for over 40 years. However, SSI

analysis has only been applied in a few building projects because the fixed base condition is

considered to provide a conservative estimation for the response of buildings under seismic loads.

This assumption of a fixed base condition adopted by practitioners is not always conservative or

cost-effective, especially for rigid buildings over soft soils. Additionally, for the case of ductile

steel frames with eccentric configurations, the influence of SSI on their seismic performance has …

Laboratory Resistivity Measurements For Soil Characterization, Behdad Mofarraj Kouchaki

Graduate Theses and Dissertations

Field based electrical resistivity measurements, such as electrical resistivity tomography (ERT) and capacitively coupled resistivity (CCR), are geophysical methods that offer a non-destructive and rapid means to collect continuous data. As such, ERT and CCR are becoming increasingly popular tools for geotechnical engineers; however, it is challenging to derive geotechnical information such as soil type, density, and water content from the data. A laboratory geophysical investigation was carried out to gain a better understanding of the parameters that affect the electrical resistivity of soils and devise a relationship between resistivity and soil type or classification. In this study, a soil …

Geophysical Assessment Of Kinion Lake Dam, Tim Allen Moody

Graduate Theses and Dissertations

Geophysical methods including Capacitively-Coupled Resistivity (CCR), Electrical Resistivity Tomography/Imaging (ERT/ERI), Multichannel Analysis of Surface Waves (MASW) with Love and Rayleigh waves and a Full-Waveform Inversion (FWI) were performed on Kinion Lake Dam, an earth-filled embankment dam that has historically experienced significant seepage and internal erosion issues. Surveys were completed along the crest and downstream toe of the dam. Results from the surveys indicate that each method is capable of resolving the bedrock depth within 1-2 m of locations shown on previous drilling logs, though some discrepancies between the methods exist. A weathered bedrock layer is believed to have led to …

In-Situ Assessment Of Concrete Bridge Decks And Pavements Using Stress-Wave Based Methods, Mengxing Li

Doctoral Dissertations

"Concrete infrastructure of United States is aging and deteriorating. Accurate assessment the condition of concrete infrastructure is critical for its maintenance and rehabilitation. Stress-wave based methods, including ultrasonic surface wave (USW) and impact echo (IE), are becoming popular for characterizing defects and mechanical properties of concrete infrastructures. In this dissertation, a comprehensive literature review of seismic wave theory and common types of defects identified in concrete infrastructures, as well as stress-wave based methods used for concrete infrastructure monitoring and characterizing on a selected concrete bridge deck and two concrete pavement segments are present. The utility and reliability of both methods …

Imaging In Karst Terrain Using The Electrical Resistivity And Multichannel Analyses Of Surface Wave Methods, Ragab W. Jaafar

Masters Theses

"Electrical resistivity tomography and multi-channel analyses of surface waves data were acquired at a study area in Phelps County in the south-central part of Missouri. The objectives of the investigation were fourfold: 1) to image the subsurface in the study area to a depth of 70 feet; 2) to compare the ERT images generated using both the dipole-dipole and Wenner-Schlumberger arrays; and 3) to assess how variations in the MASW array configuration affected MASW data quality; and 4) to compare the ERT-estimated depth to top-of-rock and the MASW-generated depth to top-of-rock.

The subsurface in the study area was imaged to …