Physical Chemistry Commons^™

The Effect Of Hydrogen Peroxide On The Corrosion Dynamics Of Carbon Steel, Kwang Soak Gabriel O'Donnell

Electronic Thesis and Dissertation Repository

The Used Fuel Container (UFC) is a key barrier in Canada’s nuclear fuel disposal plan. Understanding the radiation-induced corrosion of the carbon steel (CS) vessel is critical for predicting the long-term integrity of the UFC. Developing a mechanistic understanding of CS corrosion and the effect of solution parameters is essential.

This work investigates the effects of H₂O₂, the key radiolytic oxidant, on CS corrosion dynamics in small, stagnant solutions. Elementary processes are identified, corrosion rates are calculated, and the effects of H₂O₂ concentration are investigated. Corrosion was studied by quantifying the concentrations of …

Characterization Of Deposited Copper Oxide Films On Copper Substrates, Millicent Castillo

Electronic Thesis and Dissertation Repository

The deposition of copper oxide films on copper substrates was investigated by the electrochemical, thermal, and hydrothermal oxidation of copper. The formed oxides were characterized using various surface analytical techniques to determine the film’s morphology, composition, and thickness. The results show that by growing oxides electrochemically, a duplex layer composing of CuO and Cu₂O film was formed on the copper surface, having characteristics of being porous and possessing needle-like structures. An oxide film composed of CuO and Cu₂O, which shows minimal porosity and possess mixtures of crystalline and non-crystalline structures, is formed on the copper surface …

Near-Ir Laser Ablation Of Simulated Radiologically Contaminated Oxides On Carbon Steel Feeder Pipes, Thao Viet Do

Electronic Thesis and Dissertation Repository

As nuclear power plants age and retire from service, many countries face significant challenges concerning the safe long-term storage and disposal of large volumes of low and intermediate level radioactive wastes (L&ILW). The volumes of metallic waste are of particular concern, as when metal corrodes it produces hydrogen that could lead to pressure build-up in interim storage and disposal. In Canada, a significant fraction of the metallic wastes for Canada Deuterium Uranium (CANDU) nuclear reactors are out-of-core reactor components, such as carbon steel (CS) feeder pipes. The radioactive contamination is expected to be largely confined to the surface oxide layers …

An Investigation On The Interface Corrosion Behaviors Of Cobalt Interconnects In Chemical Mechanical Polishing Slurry, Kai-Xuan Qin, Peng-Fei Chang, Yu-Lin Huang, Ming Li, Tao Hang

Journal of Electrochemistry

Cobalt is widely regarded as the most promising interconnect material for 10 nm node and beyond. The development of a chemical mechanical planarization (CMP) slurry suitable for cobalt interconnect is a critical component for the application of cobalt interconnect. During CMP process of the interconnect layer, the achievement of high-quality surface after planarization is greatly challenged by the metal corrosion in CMP slurry. In this contribution, the corrosion behavior of cobalt in a slurry with potassium persulfate (KPS) as an oxidizer, glycine as a complexing agent, and benzotriazole (BTA) as an inhibitor was investigated. Static erosion rates (SER) of cobalt …

The Electrochemical And Corrosion Study Of Copper For Nuclear Waste Containers Under Deep Geological Disposal Conditions, Mengnan Guo

Electronic Thesis and Dissertation Repository

The proposed method for the safe disposal of Swedish, Finnish, and Canadian high-level nuclear waste (HLNW) is to isolate it in iron or steel containers with an outer copper (Cu) shell or coating and bury it in a deep geological repository (DGR). Copper has been selected as the corrosion barrier due to its stability in the aqueous anoxic environments anticipated in DGR conditions. The container will initially be exposed to humid aerated conditions which will evolve to cool and anoxic as radiation fields in the fuel decay and heat production ceases. When the DGR is cool and anoxic, sulphide (SH …

Nonlinear Dynamics Of Carbon Steel Corrosion Under Gamma Radiation, Youn Gyeong Shin

Electronic Thesis and Dissertation Repository

Corrosion of materials is still an unresolved problem affecting a multitude of industries. One of the grand challenges facing the corrosion community is the development of high-fidelity models for corrosion in actual service environments. The difficulties arise since corrosion involves transfer of metal atoms between the solid and solution phases thus making the system non-adiabatic. Interfacial transfer of atoms increases the chance of establishing systemic feedback between chemical reactions and transport processes, which results in chemical oscillation and periodic patterns on the corroding surfaces. These oscillating behavior in electrochemical measurements and pattern formation on corroding surfaces have been reported in …

Electrochemical Response Of A Single Wire-Electrode Ac Probe In 3.5wt.% Nacl, Zhen-Wen Zou, Da-Jiang Zheng, Zi-Ming Wang, Guang-Ling Song

Journal of Electrochemistry

In this paper, a recently developed single wire-electrode AC probe technology which does not need a reference or counter electrode was employed to investigate the electrochemical corrosion and sacrificial anode protection behaviors of steel and zinc in 3.5wt.% NaCl. With this simple, fast, reliable and stable probe, the instantaneous corrosion rate and accumulated corrosion loss of carbon steel in 3.5wt.% NaCl were measured, and the results revealed that both were greater than those of zinc. Furthermore, the observed different corrosion behaviors between carbon steel and zinc during the immersion could be caused by their different surface films. With the galvanic …

Galvanic Corrosion Of Copper-Coated Carbon Steel For Used Nuclear Fuel Containers, Thalia E. Standish

Electronic Thesis and Dissertation Repository

Carbon steel vessels coated with ∼3 mm of Cu have been proposed for the permanent disposal of used nuclear fuel in a deep geological repository (DGR) in Canada. In the event of an undetected defect in the Cu coating that exposes the steel substrate, galvanically accelerated corrosion of steel is, in principle, possible. To investigate this scenario, the progression of steel corrosion at the base of novel simulated through-coating defects was monitored electrochemically and imaged non-destructively using X-ray micro-computed tomography (micro-CT) as a function of time, O₂ availability (including anoxic conditions), and coating method (cold spray deposition (with and …

Electrochemical And Modelling Studies On Simulated Spent Nuclear Fuel Corrosion Under Permanent Waste Disposal Conditions, Nazhen Liu

Electronic Thesis and Dissertation Repository

The safety assessment models for the deep geological disposal of spent nuclear fuel require a fundamental understanding of the corrosion of spent fuel in a failed waste container. The overall research goal of this project is to investigate the corrosion of simulated spent fuel under permanent disposal conditions, using both model simulations and experimental investigations. A model for fuel corrosion has been expanded to determine the relative importance of radiolytic hydrogen and hydrogen from corrosion of the steel vessel in suppressing fuel corrosion. It was shown that, for CANDU (CANada Deuterium Uranium) fuel with moderate in-reactor burnup, only micromolar concentrations …

The Corrosion Of Carbon Steel Under Deep Geologic Nuclear Waste Disposal Conditions, Shannon L.W. Hill

Electronic Thesis and Dissertation Repository

The proposed disposal scenario for high-level nuclear waste (spent fuel) in Canada is emplacement within a sealed, deep geological repository (DGR) located in either granitic rock or sedimentary clay. Disposal is based on a multi-barrier approach, with the primary barrier being a sealed container which could be either dual-walled with a copper shell over an inner carbon steel vessel for granitic rock or a single thick-walled steel container for sedimentary clay. This study focuses on the corrosion behaviour of A516 Gr70 carbon steel as well as the corrosion products formed in a variety of groundwater compositions and concentrations expected within …

In Situ Detection On Electrochemical Chloride Removal Of Reinforcement In Concrete By Combined Ph/Cl- Probes, Jing-Jing Wang, Shi-Gang Dong, Xiao-Juan Zhang, Hong-Wei Lv, Yun-Chang Wu, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

In this work, the concrete samples polluted by chloride ion were electrochemically treated using galvanostatic technique, and the distributions of chloride ion concentration and pH value in the polluted concretes were in-situ monitored by embedding a combined pH/Cl^- probe during the electrochemical chloride removal. The corrosion behaviors of reinforcing steel in the concrete were simultaneously studied by using linear polarization and electrochemical impedance spectroscopy techniques (EIS). The micro environment of the concrete and corrosion rate of steel were explored during the electrochemical chloride removal. It was indicated that the Cl^- concentration in the concrete pore solution decreased with …

The Electrochemistry Of Hydrogen Peroxide On Uranium Dioxide And The Modelling Of Used Nuclear Fuel Corrosion Under Permanent Disposal Conditions, Linda Wu

Electronic Thesis and Dissertation Repository

This thesis reports a series of investigations examining the corrosion process of used nuclear fuel under permanent disposal conditions. The motivation of the project is that the safety assessment of deep geological disposal of spent nuclear fuel requires a fundamental understanding of the processes controlling fuel corrosion which could lead to the release of radionuclides to the geosphere from a failed container.

One primary objective of this project was to develop a computational model in order to simulate fuel corrosion under the disposal conditions. A series of simulations based on COMSOL were designed and developed to determine the influence of …

Characterization Of The Corrosion And Oxide Film Properties Of Alloy 600 And Alloy 800, Melissa Faichuk

Electronic Thesis and Dissertation Repository

The passive film properties of Alloy 600 and Alloy 800, both of which are used as steam generator tubing in CANDU reactors, have been studied using techniques such as polarization scans, electrochemical impedance spectroscopy and X-ray photoelectron and Auger spectroscopies. The composition of the oxides formed in a 0.1 M Na₂S₂O₃ solution have been characterized over a wide range of potentials from the pre-passive, through the passive to the transpassive regions. These changes have been correlated to the electrochemical behaviour. A second set of experiments was performed to determine the effectiveness of the surface mechanical …

Basic Principles And Applications Of Secm In Metal Corrosion, Fa-He Cao, Yan Xia, Wen-Juan Liu, Lin-Rong Chang, Jian-Qing Zhang

Journal of Electrochemistry

Scanning electrochemical microscopy (SECM) is chemical microscopy with higher spatial resolution. After 24 years of development, SECM has been widely applied in mapping and kinetics study of heterogeneous electron transfer in localized processes at solid-liquid or liquid-liquid interfaces. The fundamentals and recent advances of SECM in corrosion applications are described, including SECM mapping and kinetics on localized corrosion of metal or coating. Research work of SECM in corrosion by our group is also introduced. Future applications of SECM in corrosion are highlighted.

Applications Of Spectroscopic Ellipsometry In Corrosion Investigation, Ling-Jie Li, Yu-Ling He, Jing-Lei Lei, Sheng Tao Zhang

Journal of Electrochemistry

As a highly-sensitive and non-destructive in situ technique, spectroscopic ellipsometry has been widely applied in corrosion investigation to acquire the dynamic information of the “electrode-medium” interface during corrosion. This paper lays out some representative demonstrations in several established optical models used to interpret data obtained with spectroscopic ellipsometry in corrosion investigation. In addition, the latest trends in development of this technique are analyzed.

Multifunctional Corrosion Inhibition Behavior Of Zn-Al Calcined Layered Double Hydroxides For Steel Rebar In Nacl Solution, Xiao-Juan Zhang, Jing-Jing Wang, Shi-Gang Dong, Chang-Jian Lin

Journal of Electrochemistry

The Zn-Al layered double hydroxides (Zn-Al LDHs) and calcined products (Zn-Al CLDHs) were synthesized successfully under a routine air atmosphere. The results showed that both Zn-Al LDHs and Zn-Al CLDHs had obvious flake structures. The corrosion inhibition of Zn-Al CLDHs for steel rebar in NaCl solution was studied by electrochemical techniques. It was found that the corrosion rate of steel rebar decreased significantly after the steel rebar was treated by Zn-Al CLDHs in NaCl solution for 3 h. It was indicated that Zn-Al CLDHs could absorb Cl^- and release OH^- during their reconstruction process, which provided dual protection …

Corrosion Characteristics Of Galvanized Flat Steel For Power Grounding In Nacl Solution Medium, Yong Li, Gao-Lin Wu, Bang-Fei Deng, Ping Yang, Xue-Ming Li, Qing-Bin Zong

Journal of Electrochemistry

The corrosion behavior of power grounding galvanized flat steel was studied by polarization measurement, electrochemical impedance spectroscopy and neutral salt spray test in 5% NaCl solutions. The surface morphologies of galvanized coating and structural properties of corrosion products were observed with scanning electron microscope and X-ray diffraction spectrometer, respectively. Results showed that under the temperatures of 20~60℃, the corrosion currents of galvanized flat steel increased with the temperature rising. The corrosion rate at 60℃ was 0.8408 mA?cm-2, which is 2.9 times larger than that at 20℃. The corrosion rate dropped after reaching the maximal value of 1.95 mg?cm-2?d-1 when the …

Corrosion Electrochemical Behavior Of Am60 Magnesium Alloys In Automobile Engine Coolants, Ling-Jie Li, Sha Wang, Yin Xiao, Jun Lan, Jing-Lei Lei, Sheng-Tao Zhang, Fu-Sheng Pan

Journal of Electrochemistry

The polarization measurements and electrochemical impedance spectroscopy(EIS) were used to study the corrosion electrochemical behavior of AM60 magnesium alloys in three kinds of commercial coolants for automobile engine.Results show that the tested commercial coolants are slightly corrosive to AM60 magnesium alloys and their corrosivity varies from coolant to coolant.The coolant C is the least corrosive among the studied commercial coolants and the coolant A is more corrosive than the coolant B and C.The coolant C appears to be the most promising coolant for automobile engine made by magnesium alloys.The coolant resistivity plays an important role in the corrosion of AM60 …

Effect Of Cldh On Rebar Corrosion Behavior In Chloride Contaminated Neutral Pore Solutions, Yu-Ming Tang, Le Niu, Yu Zuo

Journal of Electrochemistry

The effect of calcined LDH-MgAl-CO3 on rebar corrosion behavior in chloride ion contaminated neutral concrete pore solutions was investigated in this paper.Corrosion potentials of rebars in pore solutions after treatment with CLDH were higher than before treatment.According to polarization tests,passivated region of rebars in pore solutions after treatment with CLDH was found apparently instead of activation.EIS tests showed that CLDH made the impedance of specimens increase.The measurements of pH and chloride ion concentration after treatment indicated that / of pore solutions decreased by 4～5 magnitude orders.

Studied Corrosion Behaviors Of Reinforcing Steel In Concrete By A Single-Dimensional Array Electrode, Lan-Qiang Li, Shi-Gang Dong, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

A single-dimensional array electrode was developed as a new electrochemical technique to image corrosion potential,galvanic current and polarization curves of reinforcing steel in concrete during corrosion process.Combining with the polarization behavior for each micro-electrode,the interactions between corrosion macrocell and corrosion microcell of the steel in concrete were evaluated.It was noticed that the corrosion macrocell and microcell occurred independently in difference regions at the initial stage of corrosion.The corrosion macrocell current can be in situ followed by corrosion potential imaging.The corrosion propagation of steel in concrete is closely related to the interactions between corrosion macrocell and corrosion microcell.

Synergism Of Complex Additives Of Dtab+Ktl For Zinc Corrosion Inhibition In Koh Solutions, Sheng-Zhou Lin, Zeng-Xin Cai, Gui-Sheng Wang, He-Bing Zhou, Wei-Shan Li

Journal of Electrochemistry

The electrochemical behaviors of Zn in 3mol/L KOH solution containing several kinds of inhibitors were investigated by weight-loss,electrochemical methods and SEM. The results showed that both the single ad-ditive and the mixed additives can suppress the corrosion of zinc in 3 mol/LKOH solution. And the inhibition ef-feciency of the mixed additives is higher than that of any single additive because of the synergistic effect between KTL and DTAB. The adsorption of DTAB on the surface of zinc has been enhanced in the presence of KTL.

Developments Of Scanning Electrochemical Probes And Their Applications In Studying Of Localized Corrosions, Chang-Jian Lin, Yan Li, Bin Lin, Rong-Gang Hu, Min Zhang, Xiang-Dong Zhuo, Rong-Gui Du

Journal of Electrochemistry

The electrochemical inhomogeneities always exist at the interface of metal/solution,and play an important and often controlling role in localized corrosion of metals in a given environment.It is necessary to develop in situ imaging techniques for further studying the electrochemical and environmental inhomogeneities at the interface of metal/solution for the localized corrosion system.In this paper,various techniques with spatial resolution,such as scanning micro reference electrode(SMET),scanning electrochemical microscope(SECM),atomic force microscope(AFM),and scanning Kelvin probe(SKP),and their applications in corrosion studies were briefly reviewed.The chemical probes and array electrode have been developed.It was concentrated to describe our newly developed techniques of the scanning electrochemical probes,including SMET …

Electrodeposition Of Al On Magnesium Alloy In Ionic Liquid, Tsai Wen-Ta, Shu-You Chen, Mu-Huan Zhuang, Chang Jeng-Kuei, Yi-Wen Sun

Journal of Electrochemistry

Electrodeposition of a metallic aluminum on a magnesium alloy in acidic aluminum chloride-1-ethyl-3-methylimidazolium chloride ionic liquids(AlCl3-EMIC) was investigated.The effects of current density and AlCl3 content in the ionic liquid on the electrodeposition behavior were studied.The results showed that aluminum could be successfully electrodeposited on the AZ91D substrate.At-0.2 V,the ionic liquid containing 60 m/o AlCl3 was optimum for Al electrodeposition.The current efficiency was higher if electrodeposition was performed at a lower applied current density.The existence of Al coating could caused a substantial increase in open circuit potential,reducing the susceptibility of Mg alloy to corrosion.The results of electrochemical impedance spectroscopy showed that …

Corrosion Inhibition Of Magnesium Alloy In 3.5% Nacl Medium By Tungstate, Ling-Jie Li, Zhi-Ming Yao, Jing-Lei Lei, Dong-Hai He, Sheng-Tao Zhang, Fu-Sheng Pan

Journal of Electrochemistry

Electrochemical impedance spectroscopy(EIS),Tafel polarization curves and scanning electron microscopy(SEM) were used to study the corrosion inhibition of AZ61 magnesium alloy in 3.5% NaCl medium with tungstate.Results showed that tungstate demonstrates strong inhibition to the corrosion of AZ61 magnesium alloy.At the concentration of 0.01 mol/L,tungstate has a high inhibition efficiency 75.5%.Tungstate is an anodic inhibitor that mainly inhibited the anodic reactions of magnesium alloy through forming a compact protective layer that covered the magnesium alloy surface active sites.

Corrosion Electrochemical Behavior Of Az31 And Az61 Magnesium Alloys In Simulated Sea Water, Ling-Jie Li, Sheng-Hai Yu, Jing-Lei Lei, Chuan-Pu Liu, Sheng-Tao Zhang, Fu-Sheng Pan

Journal of Electrochemistry

Tafel polarization curves and electrochemical impedance spectroscopy(EIS) techniques were employed to investigate the corrosion electrochemical behavior of AZ31 and AZ61 magnesium alloys.Scanning electron microscopy(SEM) was used to observe the alloy microstructure and corrosion morphology.The variation of the bulk corrosive medium pH with immersion time was recorded during the exposure of the alloys to simulated sea water.Results show that AZ61 magnesium alloy exhibits much better anti-corrosion ability than AZ31 magnesium alloy.The different corrosion behavior between the two magnesium alloys is correlated with their different content of Al alloying element.The higher content of Al in AZ61 alloy leads to the homogenerous microstructure …

Study On Electrochemical Impedance Spectroscopy Of Carbon Steel Eroded In Methyldiethanolamine Solution, Dong-Ping Wei, Rong-Zong Hu, Dan-Mei Pan, Wei-Xiong Huang, Rui Dong

Journal of Electrochemistry

Corrosion behavior of carbon steel in methyldiethanolamine(MDEA) solution was investigated by Electrochemical Impedance Spectroscopy(EIS).The results were showed that the corrosion rate of carbon steel in solution containing dissolved oxygen is higher than that in solution removed of dissolved oxygen before cathodic activation.They were reversed after cathodic activation.The corrosion rate is increased at first and then decreased when the concentration of MDEA is increased in the blank solutions.In the simulated solutions containing quantities of!heat-stable salts(HSS),the corrosion rate is decreased monotonously with increase of the MDEA concentration.As anodic polarization potential is increased,the EIS of carbon steel in HSS simulated solution showed characteristics …

Corrosion Electrochemical Behavior Of Aluminum Flake Pigmented Water-Borne Epoxy Coating On Carbon Steel In Nacl Solution, Li-Li Xue, Li-Kun Xu, Qing-Fen Li, Hong-Qing Song, Wen-Juan Zhou, Guang-Zhang Chen

Journal of Electrochemistry

The corrosion electrochemical behavior of a water-borne epoxy coating pigmented with aluminum flake on carbon steel with artificial scratch defect was studied in 3.5% NaCl solution using electrochemical impedance spectroscopy(EIS)and scanning vibrating electrode technique(SVET).The results indicated that the defect presented anodic electroactivity at the initial stage of immersion,which extended gradually with time from the scratch into the neighboring coating,lowering the coating impedance.With further immersion,however,the electroactivity of the coating/steel interface decreased significantly due to the self-repairing of the corrosion products,causing an obvious increase of the coating impedance.In the later period of immersion,more scattered electroactive areas appeared under the coating because of …

Effect Of Cracks On Corrosion Of Rebar In Concrete Studied By Wire Beam Electrode, Guo-Xi Li

Journal of Electrochemistry

The effects of crack and ethanolamine on corrosion of rebar in concrete were studied by measuring the distribution of corrosion potential and polarization resistance of iron wires in 10% NaCl solution.The results showed that the diffusion of water,oxygen and chloric ion toward concrete was accelerated by the crack which intensified the nonuniform corrosion of iron wire with the regions near to crack as anode and the uncracked regions as cathode.Ethanolamine could diffuse into the body of concrete and absorb on the surface of iron wire,which reduced iron corrosion evidently and successfully inhibited the nonuniform corrosion caused by crack without changing …

A Study Of Three Corrosion Inhibitors For Reinforcing Steel In Sps Solution By Electrochemical Methods, Bing Zhao, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

Some electrochemical techniques such as linear polarization,electrochemical noise and EIShave been employedto study the inhibition behavior of N-lauroyl sarcosinate,β-sodium glycerophosphate and D-sodium gluconate for the reinforcing steel immersed in simulated concrete pore solution(SPS) with NaCl addition.The results show that D-sodium gluconatehas an obvious inhibitive effect for the reinforcing steelin containingCl~(-)SPS solution.It has been proposed that the corrosion inhibition of D-sodium gluconate is due to its competitive adsorption and precipitation on steel surface in the simulated concrete environment.

Corrosion Behavior Of Sml,Erw Pipeline Steels Exposed To Seamud, Wei Hua

Journal of Electrochemistry

The corrosion behavior of API Spec X60 pipeline steels, including electric resistance welding(ERW) and Seamless (SML) types,in sea mud gathered fromYangtse River estuaryof the East China Sea was investigatedthrough linear polarization resistance, potentio-dynamic polarizationand electrochemical impedance measurements.The result indicate the improved corrosion resistance of SML in sea mud. The oxygen diffusion in the cathode zone determines the corrosion behavior of pipeline steel in sea mud.