Physical Sciences and Mathematics Commons^™

An Experimental Investigation Of Wing-Tip Vortex Decay In Turbulence, Hai G. Ghimire, Sean C. C. Bailey

Mechanical Engineering Faculty Publications

Particle image velocimetry measurements were conducted for a wing-tip vortex decaying in free-stream turbulence. The vortex exhibited stochastic collapse with free-stream turbulence present, with the breakdown initiating earlier for higher levels of turbulence. An increased rate of decay of the vortex tangential velocity was also observed, increasing with increasing free-stream turbulence. The decay of the vortex tangential velocity without the free-stream turbulence was well represented by viscous diffusion, resulting in an increase in the core radius and decrease in the peak tangential velocity. With the addition of free-stream turbulence, the rate of decay of the peak tangential velocity of the …

Laser Shock Wave Assisted Patterning On Niti Shape Memory Alloy Surfaces, Dovletgeldi Seyitliyev, Peizhen Li, Khomidkhodza Kholikov, Byron Grant, Haluk E. Karaca, Ali O. Er

Mechanical Engineering Faculty Publications

An advanced direct imprinting method with low cost, quick, and less environmental impact to create thermally controllable surface pattern using the laser pulses is reported. Patterned micro indents were generated on Ni₅₀Ti₅₀ shape memory alloys (SMA) using an Nd:YAG laser operating at 1064 nm combined with suitable transparent overlay, a sacrificial layer of graphite, and copper grid. Laser pulses at different energy densities which generates pressure pulses up to 10 GPa on the surface was focused through the confinement medium, ablating the copper grid to create plasma and transferring the grid pattern onto the NiTi surface. Scanning …

Recoverable Stress Induced Two-Way Shape Memory Effect On Niti Surface Using Laser-Produced Shock Wave, Dovletgeldi Seyitliyev, Peizhen Li, Khomidkhodza Kholikov, Byron Grant, Zachary Thomas, Orhan Alal, Haluk E. Karaca, Ali O. Er

Mechanical Engineering Faculty Publications

The surfaces of Ni50Ti50 shape memory alloys (SMAs) were patterned by laser scribing. This method is more simplistic and efficient than traditional indentation techniques, and has also shown to be an effective method in patterning these materials. Different laser energy densities ranging from 5 mJ/pulse to 56 mJ/pulse were used to observe recovery on SMA surface. The temperature dependent heat profiles of the NiTi surfaces after laser scribing at 56 mJ/pulse show the partially-recovered indents, which indicate a "shape memory effect (SME)" Experimental data is in good agreement with theoretical simulation of laser induced shock wave propagation inside NiTi SMAs. …

Fourth-Generation Fan Assessment Numeration System (Fans) Design And Performance Specifications, Michael P. Sama, George B. Day, Laura M. Pepple, Richard S. Gates

Biosystems and Agricultural Engineering Faculty Publications

The Fan Assessment Numeration System (FANS) is a measurement device for generating ventilation fan performance curves. Three different-sized FANS currently exist for assessing ventilation fans commonly used in poultry and livestock housing systems. All FANS consist of an array of anemometers inside an aluminum shroud that traverse the inlet or outlet of a ventilation fan. The FANS design has been updated several times since its inception and is currently in its fourth-generation (G4). The current design iteration (FANS-G4) is reported in this article with an emphasis on the hardware and software control, data acquisition systems, and operational reliability. Six FANS-G4 …

Autonomous Quadrotor Collision Avoidance And Destination Seeking In A Gps-Denied Environment, Thomas C. Kirven

Theses and Dissertations--Mechanical Engineering

This thesis presents a real-time autonomous guidance and control method for a quadrotor in a GPS-denied environment. The quadrotor autonomously seeks a destination while it avoids obstacles whose shape and position are initially unknown. We implement the obstacle avoidance and destination seeking methods using off-the-shelf sensors, including a vision-sensing camera. The vision-sensing camera detects the positions of points on the surface of obstacles. We use this obstacle position data and a potential-field method to generate velocity commands. We present a backstepping controller that uses the velocity commands to generate the quadrotor's control inputs. In indoor experiments, we demonstrate that the …

A Physics-Based Approach To Modeling Wildland Fire Spread Through Porous Fuel Beds, Tingting Tang

Theses and Dissertations--Mechanical Engineering

Wildfires are becoming increasingly erratic nowadays at least in part because of climate change. CFD (computational fluid dynamics)-based models with the potential of simulating extreme behaviors are gaining increasing attention as a means to predict such behavior in order to aid firefighting efforts. This dissertation describes a wildfire model based on the current understanding of wildfire physics. The model includes physics of turbulence, inhomogeneous porous fuel beds, heat release, ignition, and firebrands. A discrete dynamical system for flow in porous media is derived and incorporated into the subgrid-scale model for synthetic-velocity large-eddy simulation (LES), and a general porosity-permeability model is …

Spatio-Temporal Linear Stability Analysis Of Stratified Planar Wakes: Velocity And Density Asymmetry Effects, Benjamin Emerson, Swapnil Jagtap, J. Mathew Quinlan, Michael W. Renfro, Baki M. Cetegen, Tim Lieuwen

Mechanical Engineering Faculty Publications

This paper explores the hydrodynamic stability of bluff body wakes with non-uniform mean density, asymmetric mean density, and velocity profiles. This work is motivated by experiments [S. Tuttle et al., “Lean blow off behavior of asymmetrically-fueled bluff body-stabilized flames,” Combust. Flame 160, 1677 (2013)], which investigated reacting wakes with equivalence ratio stratification and, hence, asymmetry in the base flow density profiles. They showed that highly stratified cases exhibited strong, narrowband oscillations, suggestive of global hydrodynamic instability. In this paper, we present a local hydrodynamic stability analysis for non-uniform density wakes that includes base flow asymmetry. The results show …

Notes On Contributions To The Science Of Rare Earth Element Enrichment In Coal And Coal Combustion Byproducts, James C. Hower, Evan J. Granite, David B. Mayfield, Ari S. Lewis, Robert B. Finkelman

Center for Applied Energy Research Faculty and Staff Publications

Coal and coal combustion byproducts can have significant concentrations of lanthanides (rare earth elements). Rare earths are vital in the production of modern electronics and optics, among other uses. Enrichment in coals may have been a function of a number of processes, with contributions from volcanic ash falls being among the most significant mechanisms. In this paper, we discuss some of the important coal-based deposits in China and the US and critique classification systems used to evaluate the relative value of the rare earth concentrations and the distribution of the elements within the coals and coal combustion byproducts.

The Effects Of Thermal Procedure On Transformation Temperature, Crystal Structure And Microstructure Of Cu-Al-Co Shape Memory Alloy, Y. Aydoğdu, M. Kök, F. Dağdelen, A. Aydoğdu, Ali S. Turabi, Haluk E. Karaca

Mechanical Engineering Faculty Publications

The purpose of this study is to investigate the effects of different thermal procedures of the Cu-Al-Co shape memory alloy on its crystal structure, transformation temperature and microstructure. The alloys were subjected to a heat treatment and then cooling was applied at four different conditions. After the thermal process, XRD, DSC, optical microscopy and micro-hardness measurements were carried out. The experimental studies showed that crystal structure, microstructure and transformation temperature of Cu-Al-Co alloy were changed from the cooling conditions.

Effect Of Spalled Particles Thermal Degradation On A Hypersonic Flow Field Environment, Raghava S. C. Davuluri, Huaibao Zhang, Alexandre Martin

Mechanical Engineering Faculty Publications

Two-way coupling is performed between a spallation code and a hypersonic aerothermodynamics CFD solver to evaluate the effect of spalled particles on the flow field. Time accurate solutions are computed in argon and air flow fields. A single particle simulations and multiple particles simulations are performed and studied. The results show that the carbon vapor released by spalled particles tend to change the composition of the flow field, particularly the upstream region of the shock.

Modeling Of Spallation Phenomenon In An Arc-Jet Environment, Raghava Sai Chaitanya Davuluri

Theses and Dissertations--Mechanical Engineering

Space vehicles, while entering the planetary atmosphere, experience high loads of heat. Ablative materials are commonly used for a thermal protection system, which undergo mass removal mechanisms to counter the heat rates. Spallation is one of the ablative processes, which is characterized by the ejection of solid particles from the material into the flow. Numerical codes that are used in designing the heat shields ignore this phenomenon. Hence, to evaluate the effectiveness of spallation phenomenon, a numerical model is developed to compute the dynamics and chemistry of the particles. The code is one-way coupled to a CFD code that models …

A Framework For Sustainable Material Selection For Multi-Generational Components, Ryan T. Bradley

Theses and Dissertations--Mechanical Engineering

The early stages of a product’s design are a critical time for decisions that impact the entire life-cycle cost. Product designers have mastered the first generation; however, they currently do not have the ability to know the impact of their decisions on the multi-generational view. This thesis aims at closing the gap between total life-cycle information and the traditional design process in order to harbor sustainable value creation among all stakeholders involved. A framework is presented that uses a combination of a life-cycle costing methodology and an evolutionary algorithm in order to achieve a sustainability assessment for a true multi-generational …

Nonparametric Estimation Of Derivatives With Applications, Benjamin Hall

University of Kentucky Doctoral Dissertations

We review several nonparametric regression techniques and discuss their various strengths and weaknesses with an emphasis on derivative estimation and confidence band creation. We develop a generalized C(p) criterion for tuning parameter selection when interest lies in estimating one or more derivatives and the estimator is both linear in the observed responses and self-consistent. We propose a method for constructing simultaneous confidence bands for the mean response and one or more derivatives, where simultaneous now refers both to values of the covariate and to all derivatives under consideration. In addition we generalize the simultaneous confidence bands to account for heteroscedastic …

Near-Field Radiative Transfer: Thermal Radiation, Thermophotovoltaic Power Generation And Optical Characterization, Mathieu Francoeur

University of Kentucky Doctoral Dissertations

This dissertation focuses on near-field radiative transfer, which can be defined as the discipline concerned with energy transfer via electromagnetic waves at sub-wavelength distances. Three specific subjects related to this discipline are investigated, namely nearfield thermal radiation, nanoscale-gap thermophotovoltaic (nano-TPV) power generation and optical characterization. An algorithm for the solution of near-field thermal radiation problems in one-dimensional layered media is developed, and several tests are performed showing the accuracy, consistency and versatility of the procedure. The possibility of tuning near-field radiative heat transfer via thin films supporting surface phononpolaritons (SPhPs) in the infrared is afterwards investigated via the computation of …

Lectures On Computational Numerical Analysis Of Partial Differential Equations, James M. Mcdonough

Mechanical Engineering Textbook Gallery

From Chapter 1:

The purpose of these lectures is to present a set of straightforward numerical methods with applicability to essentially any problem associated with a partial differential equation (PDE) or system of PDEs independent of type, spatial dimension or form of nonlinearity.

Lectures In Computational Fluid Dynamics Of Incompressible Flow: Mathematics, Algorithms And Implementations, James M. Mcdonough

Mechanical Engineering Textbook Gallery

From Prologue:

The present lecture notes are written to emphasize the mathematics of the Navier–Stokes (N.–S.) equations of incompressible flow and the algorithms that have been developed over the past 30 years for solving them.

Evaluation Of A Mechanical System For Reconstructing Soil On Surface Mined Land, John P. Fulton, Larry G. Wells

Biosystems and Agricultural Engineering Faculty Publications

The existence of excessive soil compaction has hindered the surface mining industry from returning land to pre−mining productivity after reclamation, especially on prime farmland soils. Heavy earthmoving equipment used during reclamation tends to generate root−limiting bulk densities that adversely affect plant growth thereby decreasing yields. Therefore, the purpose of this study was to evaluate a mechanism, called the ‘Soil Regenerator,’ which reconstructs soil media at minimum bulk density during surface mine reclamation. The prototype soil forming mechanism was mounted on the front of a conventional bulldozer. Soil was placed in long narrow windrows by a scraper or bulldozer. As the …

A Mechanical System For Soil Reconstruction, John Patrick Fulton, Larry G. Wells, Timothy D. Smith

Biosystems and Agricultural Engineering Faculty Publications

One of the most perplexing problems associated with reclaiming surface–mined lands is excessive compaction of soil due to the heavy earthmoving equipment used during the reclamation process. Over the years, some innovative material handling schemes have been devised to limit vehicle traffic during reclamation on reconstructed soil. However, final grading operations can often create root–limiting bulk densities, which affect plant growth and yield. The purpose of this article is to describe a mechanism designed at the University of Kentucky whereby mine soil can be reconstructed without introducing compaction caused by surface traffic in order for the soil to sustain desirable …