Physical Sciences and Mathematics Commons^™

Universality Of Local Dissipation Scales In Turbulent Boundary Layer Flows With And Without Free-Stream Turbulence, Sabah F. H. Alhamdi, Sean C. C. Bailey

Mechanical Engineering Faculty Publications

Measurements of the small-scale dissipation statistics of turbulent boundary layer flows with and without free-stream turbulence are reported for Re_τ ≈ 1000 (Re_θ ≈ 2000). The scaling of the dissipation scale distribution is examined in these two boundary conditions. Results demonstrated that the local large-scale Reynolds number based on the measured longitudinal integral length scale fails to properly normalize the dissipation scale distribution near the wall in these two free-stream conditions due to the imperfect characterization of the upper bound of the inertial cascade by the integral length scale. A surrogate found from turbulent kinetic energy and …

Additional Data Via Autonomous Systems To Supplement Traditional Sparse Sources For Weather Forecasting And Atmospheric Science, Suzanne Weaver Smith

Commonwealth Computational Summit

No abstract provided.

The Effect Of Inlet Pulsations On Primary Atomization Of Liquid Jets, Kyle Windland, Prashant Khare

Commonwealth Computational Summit

Objectives

• Elucidate the physics underlying the primary atomization of liquid jets.
• Investigate the effect of inlet pulsations on the atomization process.
• Identify the reliability of numerical predictions using uncertainty quantification techniques (UQ) and sensitivity analyses.

High-Fidelity Simulations Of Water Jet In Air Crossflow, Austin Johnston, Prashant Khare

Commonwealth Computational Summit

Objectives

• Investigate detailed physics underlying liquid jets in crossflow configurations applicable to various applications such as, gas-turbine, scramjet, and afterburner fuel injection.
• Develop models to predict the statistical behaviors of resulting droplets.

Solvent Degradation And Emissions From A 0.7mwe Pilot Co2 Capture System With Two-Stage Stripping, Jesse Thompson, Heather Nikolic, Megan Combs, Saloni Bhatnagar, Jonathan Pelgen, Keemia Abad, Kunlei Liu

Center for Applied Energy Research Faculty and Staff Publications

The UKy-CAER team successfully tested an advanced 0.7 MWe post-combustion CO₂ capture system on a coal-fired power plant using a heat integration process combined with two-stage stripping to enhance the CO₂ absorber performance. One of the unique feature of the UKy-CAER integrated process is a two-stage stripping unit for solvent regeneration. The secondary stripper is empowered by the heat rejection from a conventional steam-heated (primary) stripper. The secondary stripper outlet stream at the commercial scale can be used as boiler secondary combustion air, consequently enriching the flue gas with CO₂, resulting in less energy penalty required …

Mapping And Integrating Value Creation Factors With Life-Cycle Stages For Sustainable Manufacturing, P. Bilge, S. Emec, G. Seliger, Ibrahim S. Jawahir

Institute for Sustainable Manufacturing Faculty Publications

Instead of implementing each element individually, engineers must be aware of multiple interactions among all major value creation factors and their life-cycle stages. Interactions are analyzed by a set of factors and hierarchical levels within a production system based on empirical observations and described in analytical models. Such analyses and missing information about the current condition of the system and its parts remain limited to addressing specific aspects of interactions among factors and stages for multiple decision making. To build a case-based scope addressing the interactions among a set of factors and life-cycle stages, a comprehensive approach for mapping and …

An Experimental Investigation Of Wing-Tip Vortex Decay In Turbulence, Hai G. Ghimire, Sean C. C. Bailey

Mechanical Engineering Faculty Publications

Particle image velocimetry measurements were conducted for a wing-tip vortex decaying in free-stream turbulence. The vortex exhibited stochastic collapse with free-stream turbulence present, with the breakdown initiating earlier for higher levels of turbulence. An increased rate of decay of the vortex tangential velocity was also observed, increasing with increasing free-stream turbulence. The decay of the vortex tangential velocity without the free-stream turbulence was well represented by viscous diffusion, resulting in an increase in the core radius and decrease in the peak tangential velocity. With the addition of free-stream turbulence, the rate of decay of the peak tangential velocity of the …

Laser Shock Wave Assisted Patterning On Niti Shape Memory Alloy Surfaces, Dovletgeldi Seyitliyev, Peizhen Li, Khomidkhodza Kholikov, Byron Grant, Haluk E. Karaca, Ali O. Er

Mechanical Engineering Faculty Publications

An advanced direct imprinting method with low cost, quick, and less environmental impact to create thermally controllable surface pattern using the laser pulses is reported. Patterned micro indents were generated on Ni₅₀Ti₅₀ shape memory alloys (SMA) using an Nd:YAG laser operating at 1064 nm combined with suitable transparent overlay, a sacrificial layer of graphite, and copper grid. Laser pulses at different energy densities which generates pressure pulses up to 10 GPa on the surface was focused through the confinement medium, ablating the copper grid to create plasma and transferring the grid pattern onto the NiTi surface. Scanning …

Recoverable Stress Induced Two-Way Shape Memory Effect On Niti Surface Using Laser-Produced Shock Wave, Dovletgeldi Seyitliyev, Peizhen Li, Khomidkhodza Kholikov, Byron Grant, Zachary Thomas, Orhan Alal, Haluk E. Karaca, Ali O. Er

Mechanical Engineering Faculty Publications

The surfaces of Ni50Ti50 shape memory alloys (SMAs) were patterned by laser scribing. This method is more simplistic and efficient than traditional indentation techniques, and has also shown to be an effective method in patterning these materials. Different laser energy densities ranging from 5 mJ/pulse to 56 mJ/pulse were used to observe recovery on SMA surface. The temperature dependent heat profiles of the NiTi surfaces after laser scribing at 56 mJ/pulse show the partially-recovered indents, which indicate a "shape memory effect (SME)" Experimental data is in good agreement with theoretical simulation of laser induced shock wave propagation inside NiTi SMAs. …

Fourth-Generation Fan Assessment Numeration System (Fans) Design And Performance Specifications, Michael P. Sama, George B. Day, Laura M. Pepple, Richard S. Gates

Biosystems and Agricultural Engineering Faculty Publications

The Fan Assessment Numeration System (FANS) is a measurement device for generating ventilation fan performance curves. Three different-sized FANS currently exist for assessing ventilation fans commonly used in poultry and livestock housing systems. All FANS consist of an array of anemometers inside an aluminum shroud that traverse the inlet or outlet of a ventilation fan. The FANS design has been updated several times since its inception and is currently in its fourth-generation (G4). The current design iteration (FANS-G4) is reported in this article with an emphasis on the hardware and software control, data acquisition systems, and operational reliability. Six FANS-G4 …

A Physics-Based Approach To Modeling Wildland Fire Spread Through Porous Fuel Beds, Tingting Tang

Theses and Dissertations--Mechanical Engineering

Wildfires are becoming increasingly erratic nowadays at least in part because of climate change. CFD (computational fluid dynamics)-based models with the potential of simulating extreme behaviors are gaining increasing attention as a means to predict such behavior in order to aid firefighting efforts. This dissertation describes a wildfire model based on the current understanding of wildfire physics. The model includes physics of turbulence, inhomogeneous porous fuel beds, heat release, ignition, and firebrands. A discrete dynamical system for flow in porous media is derived and incorporated into the subgrid-scale model for synthetic-velocity large-eddy simulation (LES), and a general porosity-permeability model is …

Autonomous Quadrotor Collision Avoidance And Destination Seeking In A Gps-Denied Environment, Thomas C. Kirven

Theses and Dissertations--Mechanical Engineering

This thesis presents a real-time autonomous guidance and control method for a quadrotor in a GPS-denied environment. The quadrotor autonomously seeks a destination while it avoids obstacles whose shape and position are initially unknown. We implement the obstacle avoidance and destination seeking methods using off-the-shelf sensors, including a vision-sensing camera. The vision-sensing camera detects the positions of points on the surface of obstacles. We use this obstacle position data and a potential-field method to generate velocity commands. We present a backstepping controller that uses the velocity commands to generate the quadrotor's control inputs. In indoor experiments, we demonstrate that the …