Open Access. Powered by Scholars. Published by Universities.®
- Discipline
-
- Manufacturing (5)
- Materials Science and Engineering (5)
- Computer-Aided Engineering and Design (4)
- Structural Materials (4)
- Civil and Environmental Engineering (2)
-
- Engineering Mechanics (2)
- Engineering Science and Materials (2)
- Mechanics of Materials (2)
- Other Materials Science and Engineering (2)
- Structural Engineering (2)
- Construction Engineering and Management (1)
- Dynamics and Dynamical Systems (1)
- Electro-Mechanical Systems (1)
- Hydraulic Engineering (1)
- Other Mechanical Engineering (1)
Articles 1 - 6 of 6
Full-Text Articles in Applied Mechanics
Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield
Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield
All Undergraduate Projects
What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …
Jcati Base Plate, Jacob Atamian
Jcati Base Plate, Jacob Atamian
All Undergraduate Projects
Students of the Mechanical Engineering Technology (MET) program at Central Washington University have contributed to an ongoing Carbon Fiber Recycler project funded by the Joint Center for Aerospace Technology Innovation (JCATI). The goal of this project was to modify the existing recycling system to produce a higher success rate of recycled carbon composite material. This report focuses on increasing the rigidity of the crushing gears so that the deflection occurring among the components during operation was below 0.005 inches to ensure proper operating conditions. The operating speed of the crushing gears was 2.5 rpm with a crushing load of 10,500 …
Mini Rc Baja Car, Jason Schindler
Mini Rc Baja Car, Jason Schindler
All Undergraduate Projects
Incorporating each aspect of engineering incorporated into a senior project is difficult. That is why an RC Baja car is a great senior project for Mechanical Engineering students. The approach that students must take to design, construct, and test the car is to set parameters, and to make overall goals that can be easily measured. These goals include, but not limited to things like a $700 budget and the ability to withstand a 1-foot drop to a flat surface on all four wheels simultaneously. First, the design must meet the specifications and rules that are set previously. This ensures that …
Jcati Carbon Fiber Recycling Shredder, Benjamin Cooley
Jcati Carbon Fiber Recycling Shredder, Benjamin Cooley
All Undergraduate Projects
Once carbon fibers are cast into a resin and used in a composite material, retrieving those fibers can be a difficult task. However, it is beneficial to recycle and reuse the fibers from old unneeded components rather than pay the cost of acquiring new ones. The Joint Center for Aerospace Technology Innovation (JCATI) carbon fiber recycling device condenses the multistep process of extracting the fibers by integrating all steps into one automated device. In the previous version of the device, the cutting blades turned the long composite strips into thin fingers but did not sever them across the width.
The …
Balsa Wood Bridge, Andrew Harris
Balsa Wood Bridge, Andrew Harris
All Undergraduate Projects
Faculty at Central Washington University proposed a challenge to mechanical engineering students that could be accomplished in an in-home setting. The goal was to create a balsa wood bridge, weighing no more than 85 grams, that can support a load over an open span and raise above its resting position by means of a mechanical system. To produce a successful solution to the problem, a vertical lift bridge was created consisting of two lifting towers and a load bearing bridge. Using equations of static equilibrium and strength of materials, the required width for each member was determined. Project requirements were …
Asme Rc Baja Car Drivetrain, Gizan G. Gando
Asme Rc Baja Car Drivetrain, Gizan G. Gando
All Undergraduate Projects
The purpose of the RC Baja Car is to compete in the American Society of Mechanical Engineers (ASME) competition, a series of events to prove the functionality of the vehicle. This series of events includes the Slalom, Drag, and Baja race. The Slalom is a test in the steering capability of the car. The Drag is a test in the acceleration of the car in a straight line. Lastly, the Baja puts all factors together in a race to test every component of the car. This project is about building an RC car that can function under these conditions and …