Applied Mechanics Commons^™

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …

Jcati Base Plate, Jacob Atamian

All Undergraduate Projects

Students of the Mechanical Engineering Technology (MET) program at Central Washington University have contributed to an ongoing Carbon Fiber Recycler project funded by the Joint Center for Aerospace Technology Innovation (JCATI). The goal of this project was to modify the existing recycling system to produce a higher success rate of recycled carbon composite material. This report focuses on increasing the rigidity of the crushing gears so that the deflection occurring among the components during operation was below 0.005 inches to ensure proper operating conditions. The operating speed of the crushing gears was 2.5 rpm with a crushing load of 10,500 …

Mini Rc Baja Car, Jason Schindler

All Undergraduate Projects

Incorporating each aspect of engineering incorporated into a senior project is difficult. That is why an RC Baja car is a great senior project for Mechanical Engineering students. The approach that students must take to design, construct, and test the car is to set parameters, and to make overall goals that can be easily measured. These goals include, but not limited to things like a $700 budget and the ability to withstand a 1-foot drop to a flat surface on all four wheels simultaneously. First, the design must meet the specifications and rules that are set previously. This ensures that …

Jcati Carbon Fiber Recycling Shredder, Benjamin Cooley

All Undergraduate Projects

Once carbon fibers are cast into a resin and used in a composite material, retrieving those fibers can be a difficult task. However, it is beneficial to recycle and reuse the fibers from old unneeded components rather than pay the cost of acquiring new ones. The Joint Center for Aerospace Technology Innovation (JCATI) carbon fiber recycling device condenses the multistep process of extracting the fibers by integrating all steps into one automated device. In the previous version of the device, the cutting blades turned the long composite strips into thin fingers but did not sever them across the width.

The …

Balsa Wood Bridge, Andrew Harris

All Undergraduate Projects

Faculty at Central Washington University proposed a challenge to mechanical engineering students that could be accomplished in an in-home setting. The goal was to create a balsa wood bridge, weighing no more than 85 grams, that can support a load over an open span and raise above its resting position by means of a mechanical system. To produce a successful solution to the problem, a vertical lift bridge was created consisting of two lifting towers and a load bearing bridge. Using equations of static equilibrium and strength of materials, the required width for each member was determined. Project requirements were …

Stair Climbing Hand Truck, James Mcpherson

All Undergraduate Projects

Abstract

Getting a heavy object up a flight of stairs usually requires a team of two or more people. Even with a team of people, the task is often still difficult, dangerous, and possibly insurmountable by one person. This problem is especially prevalent in for those who are moving into apartment complexes. Most apartment complexes have many buildings with two or more floors of living quarters, and elevators are often missing. This project sought to offer a solution to this problem. The solution in question; a motorized hand-truck with 2, trigonal planar pinwheels in place of the stock wheels. The …

Autojack - Hydraulic Powertrain System, Tyce Vu

All Undergraduate Projects

A primary problem for mechanics and automotive enthusiasts is the risk associated with lifting and securing a vehicle with conventional jack stands. Often times, improper jack-stand installation results in the vehicle collapsing unexpectedly, causing injury and/or death. This problem can be minimized through the application of a newly re-designed vehicle lifting system. The conventional method for lifting cars is time consuming and can be unsafe in many circumstances. A better, safer, and more efficient lift design was needed; the AutoJack. The approach of the AutoJack design was entirely focused on the safety of lifting a vehicle. Safety was improved by …

Composite Cold Expansion Tooling, Andrew Amos

All Undergraduate Projects

In the world of aircraft manufacturing, cold expansion products literally hold these aircraft together. The problem faced today is that the Little Brute Hydraulic Puller designed and built by Fatigue Technology Inc. is a handheld steel hydraulic cylinder that is heavy and expensive to produce. In a market that demands continuous improvement, there is a constant push to make the product cheaper, better and lighter. In order to accomplish this demand a composite tube will be substituted in the design as the primary pressure cylinder instead of the traditional steel pressure cylinder in order to create a lighter and cheaper …