Applied Mechanics Commons^™

Simulation Of Wave Propagation In Granular Particles Using A Discrete Element Model, Syed Tahmid Hussan

Electronic Theses and Dissertations

The understanding of Bender Element mechanism and utilization of Particle Flow Code (PFC) to simulate the seismic wave behavior is important to test the dynamic behavior of soil particles. Both discrete and finite element methods can be used to simulate wave behavior. However, Discrete Element Method (DEM) is mostly suitable, as the micro scaled soil particle cannot be fully considered as continuous specimen like a piece of rod or aluminum. Recently DEM has been widely used to study mechanical properties of soils at particle level considering the particles as balls. This study represents a comparative analysis of Voigt and Best …

Cfrp Delamination Density Propagation Analysis By Magnetostriction Theory, Brandon Eugene Williams

All Dissertations

While Carbon Fiber Reinforced Polymers (CFRPs) have exceptional mechanical properties concerning their overall weight, their failure profile in demanding high-stress environments raises reliability concerns in structural applications. Two crucial limiting factors in CFRP reliability are low-strain material degradation and low fracture toughness. Due to CFRP’s low strain degradation characteristics, a wide variety of interlaminar damage can be sustained without any appreciable change to the physical structure itself. This damage suffered by the energy transfer from high- stress levels appears in the form of microporosity, crazes, microcracks, and delamination in the matrix material before any severe laminate damage is observed. This …

Numerical Modeling And Simulation On Deformation And Failure Behaviors Of Polymeric Materials, Heng Feng

Electronic Thesis and Dissertation Repository

Featured by biocompatibility, high compliance and capacity in sustaining large deformation, dielectric elastomers (DEs) and hydrogels have gained extensive research popularity for their potential applications in the fields of soft robots, biomimetics, tissue engineering, drug delivery, and energy harvesting. The design of such soft and smart material-based devices and structures requires deep understanding and accurate simulation of their constitutive behaviors, which is challenged by their nonlinear material properties due to unique microstructures and multi-physics coupling. Meanwhile, in different application contexts, those structures are also susceptible to different failure modes, imposing further challenges in simulating and predicting their performance. To fulfill …

Characterization Of Mechanically Recycled Polylactic Acid (Pla) Filament For 3d-Printing By Evaluating Mechanical, Thermal, And Chemical Properties And Process Performance, Mahsa Shabani Samghabady

All Theses

Polylactic acid (PLA) is a biopolymer made from renewable resources such as sugar and corn. PLA filament is a popular material used in Fused Deposition Modeling (FDM) 3D-printing. While this material has many advantages, all the failed parts, support structures, rafts, nozzle tests, and the many prototype iterations during the 3D-printing process contribute to the plastic pollution and release of greenhouse gases. Although PLA is biodegradable, it can take years to degrade in landfills. Instead of throwing away PLA waste and buying new filaments, PLA can be recycled. Amongst the different recycling technologies, mechanical recycling is the most environmentally friendly. …

Dome Tester, Clark Bates, Nikolas M. Kulin

Williams Honors College, Honors Research Projects

We are reconfiguring and modifying the previously built dome tester to be more user friendly and mechanically applicable. This has a long-term goal of being a usable teaching tool for manufacturing education within the college of engineering and polymer sciences. The dome tester pushes a metal dome into a clamped sheet of metal to test its forming limits and where necking occurs. We have implemented a better method of viewing the sheet sample as it is being deformed, and improved measuring methods for the distance a sample is deformed. By introducing these changes in conjunction with improved documentation of the …

Grinding And Super-Finishing Test Machine Project, Michael Simon

Williams Honors College, Honors Research Projects

A research project in The University of Akron to study grinding and super-finishing of silicon nitride ceramic was initiated by Dr. Siamak Farhad and sponsored by the Timken Company, with the assistance of undergraduate students Michael Simon, Ryan Hosso and Mathew Rozmajzl. The study required analysis of forces and scratches generated during grinding processes of silicon nitride samples. A testing assembly was designed and constructed to record the forces generated during grinding and super-finishing of silicon nitride samples in a computer-numerical-control machine. Silicon nitride samples were subjected to desired grinding and super-finishing operations and all forces generated during the process …

Assessing Mechanical Performance Of Dissimilar Steel Systems Made Via Wire-Arc Additive Manufacturing, Obed Daniel Acevedo

Masters Theses

Hot stamping is part of a specific type of metalworking procedure widely used in the automotive industry. This research seeks to help make hot stamp tooling component production more cost-effective by using large-scale additive manufacturing. Additive manufacturing can produce dissimilar steel components that can be more cost-effective and time-efficient and allow for complex geometries to be made. A dissimilar steel system consisting of 410 martensitic stainless steel and AWS ER70S-6 mild steel is proposed to make hot stamps, making them more cost-efficient. However, the material interface's mechanical behavior in 410SS-mild steel additively manufactured material systems is not well understood. This …

Development Of Novel Battery Materials For Lithium-Ion Batteries And Beyond, Jiyu Cai

Graduate Theses and Dissertations

As fossil fuels are depleting and causing environmental issues, it becomes imperative to widely implement renewable energies (e.g., solar and wind power). In this context, electrical energy storage (EES) systems are essential to accommodate the intermittent supply and uneven distribution of renewable energies. To this end, high-energy-density EES devices are highly demanded, such as rechargeable batteries. This dissertation presents my efforts in developing novel battery materials for lithium-ion batteries (LIBs), sodium-ion batteries (SIBs), and solidstate lithium batteries (SSLBs). These efforts include electrochemical evaluations of battery materials, surface modifications of electrodes via atomic layer deposition (ALD), and advanced characterizations of batteries …

Phase-Field Modeling Of The Polymer Membrane Formation Process For Micro- And Ultra-Filtration, Michael Rosario Cervellere

Graduate Theses and Dissertations

Porous polymer membrane filters are widely used in separation and filtration process. Micro- and ultra-filtration membranes are commonly used in biopharmaceutical applications such as filtering viruses and separating proteins from a carrier solution. The formation of these membrane filters via phase inversion is a complex and interconnected process where varying casting conditions can have a wide variety of effects on the final membrane morphol- ogy. Tailoring membrane filters for specific performance characteristics is a tedious and time consuming process. The time and length scales of membrane formation make it extremely difficult to experimentally observe membrane formation. Modeling the membrane formation …

Influence Of Extracellular Matrix Stiffness And Topography On Neuronal Cell Behavior And Neurite Outgrowth, Mohan Yasodharababu

Graduate Theses and Dissertations

The focus of regeneration therapy for traumatic brain injuries and Alzheimer's disease is on the promotion and growth of neuronal cells. In vitro research attempts to improve this by modifying the stiffness and topography of the extracellular matrix (ECM). However, the limitations of in vitro experiments make it difficult to control the individual factors influencing neuronal cell growth. A computational model can be used to decouple individual factors and study them individually to gain a better understanding of the mechanics between the neuronal cell and ECM, which will aid in the design of in vitro experimental studies.

This study develops …

Material Property Heterogeneity In Dimensional Lumber And Its Relationship To Mass Timber Performance, Fiona O'Donnell

Doctoral Dissertations

According to the Environmental Protection Agency, buildings account for 38% of the United States' carbon dioxide emissions, providing architects and structural engineers a unique opportunity to mitigate a significant factor driving climate change by implementing innovative and sustainable technology in infrastructure design. Wood and mass timber products are becoming an increasingly popular alternative building material due to their economic and environmental benefits. The natural growth of wood leads to highly heterogeneous material properties. Defects such as checks, knots, and localized slope of grain contribute to some of this variation; however, wood properties vary significantly even in clear wood. Using mass …

Fluid-Structure Interaction Of Nrel 5-Mw Wind Turbine, Mohamed Sayed Elkady Abd-Elhay

Theses and Dissertations

Wind energy is considered one of the major sources of renewable energy. Nowadays, wind turbine blades could exceed 100 m to maximize the generated power and minimize produced energy cost. Due to the enormous size of the wind turbines, the blades are subjected to failure by aerodynamics loads or instability issues. Also, the gravitational and centrifugal loads affect the wind turbine design because of the huge mass of the blades. Accordingly, wind turbine simulation became efficient in blade design to reduce the cost of its manufacturing. The fluid-structure interaction (FSI) is considered an effective way to study the turbine's behavior …

Process-Structure-Property Relationships In 3d-Printed Epoxy Composites Produced Via Material Extrusion Additive Manufacturing, Nadim S. Hmeidat

Doctoral Dissertations

Extrusion-based additive manufacturing (AM) technologies, such as direct ink writing (DIW), offer unique opportunities to create composite materials and novel multi-material architectures that are not feasible using other AM technologies. DIW is a novel 3D-printing approach in which viscoelastic inks, with favorable rheological properties, are extruded through fine nozzles and patterned in a filament form at room temperature.

Recent developments in DIW of polymer composites have led to expanding the range of materials used for printing, as well as introducing novel deposition strategies to control filler orientation and create improved functional/structural composite materials. Despite these substantial advancements, the successful and …

A Single-Stage Passive Vibration Isolation System For Scanning Tunneling Microscopy, Toan T. Le

Master's Theses

Scanning Tunneling Microscopy (STM) uses quantum tunneling effect to study the surfaces of materials on an atomic scale. Since the probe of the microscope is on the order of nanometers away from the surface, the device is prone to noises due to vibrations from the surroundings. To minimize the random noises and floor vibrations, passive vibration isolation is a commonly used technique due to its low cost and simpler design compared to active vibration isolation, especially when the entire vibration isolation system (VIS) stays inside an Ultra High Vacuum (UHV) environment. This research aims to analyze and build a single-stage …

Diseño De Un Aplicativo Para El Proceso De Selección De Resortes En Dos Referencias De Puertas Automáticas, Leidy Tatiana Toro Bermúdez, Francy Stefanía Cruz Guevara

Ingeniería Industrial

En este proyecto se desarrolla un aplicativo de selección de resortes para el proceso de instalación de dos referencias de puerta levadiza y basculante, para la empresa del sector metalmecánico Tecnipuertas LET, analizando la relación entre las características de la puerta: alto, ancho, peso, calibre, material y el efecto de las anteriores en los parámetros del resorte: número de vueltas, longitud, diámetro interno, externo y diámetro del alambre.

El desarrollo se llevó a cabo en tres fases en la primera se realizó el análisis del proceso de fabricación e instalación y la caracterización de los materiales; realizada mediante estudios metalográfico …

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …

Mini Rc Baja Car, Jason Schindler

All Undergraduate Projects

Incorporating each aspect of engineering incorporated into a senior project is difficult. That is why an RC Baja car is a great senior project for Mechanical Engineering students. The approach that students must take to design, construct, and test the car is to set parameters, and to make overall goals that can be easily measured. These goals include, but not limited to things like a $700 budget and the ability to withstand a 1-foot drop to a flat surface on all four wheels simultaneously. First, the design must meet the specifications and rules that are set previously. This ensures that …

Adhesion And Deformation Mechanisms Of Polydopamine And Polytetrafluoroethylene: A Multiscale Computational Study, Matthew Brownell

Graduate Theses and Dissertations

Polydopamine (PDA) has been shown to bond via covalent bonding, van der Waals forces, and hydrogen bonding and is known to adhere strongly to almost any material. The application of PDA between a substrate and a PTFE surface coating has resulted in low friction and a greatly reduced wear rate. Previous research probing the capabilities and limitations of PDA/PTFE films have studied the wear and mechanical properties of the film, but the overall adhesive and deformation mechanisms remain unclear.

In this research, we investigate the tribological properties of PDA and PTFE molecules and composites from the atomic to the microscale …

The Development Of All Solid-State Optical Cryo-Cooler, Junwei Meng

Optical Science and Engineering ETDs

This dissertation describes the development of an all solid-state optical cryo-cooler. Crystals of 10% wt. ytterbium-doped yttrium lithium fluoride (Yb³⁺:YLF) are used to cool an infrared HgCdTe sensor payload to an absolute temperature below 135 K, equivalent to delta T equal 138 K below ambient. This record level of cooling is accomplished with a single stage, in a completely vibration-free environment, with a corresponding cooling power of 190 mW. This milestone is made possible by the design and fabrication of an undoped YLF thermal link that efficiently shields the payload with a non-right angle kink from intense anti-Stokes …

Multiscale Modeling Of Carbon Fibers/Graphene Nanoplatelets/Epoxy Hybrid Composites For Aerospace Applications, Hashim Al Mahmud

Dissertations, Master's Theses and Master's Reports

Significant research effort has been dedicated for decades to improve the mechanical properties of aerospace polymer-based composite materials. Lightweight epoxy-based composite materials have increasingly replaced the comparatively heavy and expensive metal alloys used in aeronautical and aerospace structural components. In particular, carbon fibers (CF)/graphene nanoplatelets (GNP)/epoxy hybrid composites can be used for this purpose owing to their high specific stiffness and strength. Therefore, this work has been completed to design, predict, and optimize the effective mechanical properties of CF/GNP/epoxy composite materials at different length scales using a multiscale modeling approach. The work-flow of modeling involves a first step of using …

Dynamic Loading Experimentation And Surface Imaging Of Pressure Vessel Loadcell Fractures, Austin T. Sumner

Honors College Theses

Pressure vessels are very common pieces of equipment in industry and they are used for a variety of applications. It is standard in industry to rest pressure vessels on load cells. For some special cases, the pressure vessels are rested on load cells instead of solid foundation. Pressure vessels and their loadcells are generally designed for static environmental conditions and loading and tend to experience adverse effects when exposed to dynamic environments, such as hurricanes and earthquakes. These adverse-loading conditions cause vibrations and asymmetrical loading on the load cells, which can concurrently cause unexpected failure. This research investigates the effects …

Increasing Access To Pv Technology Through Sustainable Racking: A Review Of Existing Literature And Ground Mounted Fixed Tilt Designs, And What Can Be Done Next, Parijata Prabhakara

Dissertations, Master's Theses and Master's Reports

There is a lack of literature on the structural balance of systems (BOS), also called racking, for ground mount, fixed-tilt solar PV systems. Literature that exists discusses mostly rooftop racking and installations, additional wind loading, and weight considerations imposed on roofs, and little guidance is provided in building codes. The lack of peer-reviewed guidance on design requirements for domestic and large-scale application solar PV racking systems leaves most consumers relying on expensive, patented, off-the-shelf hardware. As PV cell technology and module costs have improved, we can start to focus on PV BOS improvements (particularly racking) and move towards sustainable designs …

General Nonlinear-Material Elasticity In Classical One-Dimensional Solid Mechanics, Ronald Joseph Giardina Jr

University of New Orleans Theses and Dissertations

We will create a class of generalized ellipses and explore their ability to define a distance on a space and generate continuous, periodic functions. Connections between these continuous, periodic functions and the generalizations of trigonometric functions known in the literature shall be established along with connections between these generalized ellipses and some spectrahedral projections onto the plane, more specifically the well-known multifocal ellipses. The superellipse, or Lam\'{e} curve, will be a special case of the generalized ellipse. Applications of these generalized ellipses shall be explored with regards to some one-dimensional systems of classical mechanics. We will adopt the Ramberg-Osgood relation …

Investigation Of Fundamental Principles Of Rigid Body Impact Mechanics, Khalid Alluhydan

Mechanical Engineering Research Theses and Dissertations

In impact mechanics, the collision between two or more bodies is a common, yet a very challenging problem. Producing analytical solutions that can predict the post-collision motion of the colliding bodies require consistent modeling of the dynamics of the colliding bodies. This dissertation presents a new method for solving the two and multibody impact problems that can be used to predict the post-collision motion of the colliding bodies. Also, we solve the rigid body collision problem of planar kinematic chains with multiple contacts with external surfaces.

In the first part of this dissertation, we study planar collisions of Balls and …

Effect Of The Nonlinear Material Viscosity On The Performance Of Dielectric Elastomer Transducers, Yuanping Li

Electronic Thesis and Dissertation Repository

As a typical type of soft electroactive materials, dielectric elastomers (DEs) are capable of producing large voltage-induced deformation, which makes them desirable materials for a variety of applications in transduction technology, including tunable oscillators, resonators, biomimetics and energy harvesters. The dynamic and energy harvesting performance of such DE-based devices is strongly affected not only by multiple failure modes such as electrical breakdown, electromechanical instability, loss-of-tension and fatigue, but also by their material viscoelasticity. Moreover, as suggested by experiments and theoretical studies, DEs possess nonlinear relaxation processes, which makes modeling of the performance of DE-based devices more challenging.

In this thesis, …

Structural Health Monitoring Of Composite Parts: A Review, Jacob Pessin

Honors Theses

Structural health monitoring has the potential to allow composite structures to be more reliable and safer, then by using more traditional damage assessment techniques. Structural health monitoring (SHM) utilizes individual sensor units that are placed throughout the load bearing sections of a structure and gather data that is used for stress analysis and damage detection. Statistical time based algorithms are used to analyze collected data and determine both damage size and probable location from within the structure. While traditional calculations and life span analysis can be done for structures made of isotropic materials such as steel or other metals, composites …

Predicting The Mechanical Properties Of Nanocomposites Reinforced With 1-D, 2-D And 3-D Nanomaterials, Scott Edward Muller

Graduate Theses and Dissertations

Materials with features at the nanoscale can provide unique mechanical properties and increased functionality when included as part of a nanocomposite. This dissertation utilizes computational methods at multiple scales, including molecular dynamics (MD) and density functional theory (DFT), and the coupled atomistic and discrete dislocation multiscale method (CADD), to predict the mechanical properties of nanocomposites possessing nanomaterials that are either 1-D (carbyne chains), 2-D (graphene sheets), or 3-D (Al/amorphous-Si core-shell nanorod).

The MD method is used to model Ni-graphene nanocomposites. The strength of a Ni-graphene nanocomposite is found to improve by increasing the gap between the graphene sheet and a …

Transferring Power Through A Magnetic Couple, Nickolas Cruz Villalobos Jr.

Senior Theses

Properties of several working magnetic coupled rotors have been measured and their performance compared to theoretical models. Axial magnetic couplers allow rotors to work within harsh environments, without the need for seals, proper alignment, or overload protection on a motor. The influence of geometrical parameters, such as distance from the center of the rotors, polarity arrangement, and the number of dipole pairs were experimentally tested. These results can be used to improve rotor designs, to increase strength and efficiency.

Reinventing The Wheel, Esther K. Unti, Ahmed Z. Shorab, Patrick B. Kragen, Adam M. Menashe

Mechanical Engineering

Reinventing the Wheel selected tires and designed wheels for the 2018 Cal Poly, San Luis Obispo Formula SAE combustion vehicle. Available tire options were evaluated for steady-state and transient performance as well as vehicle integration. A single-piece composite wheel with hollow spokes was designed to meet stiffness, strength, and tolerance requirements. A detailed study of wheel loading and geometric structural efficiency was performed. Finite element analysis was used to iterate the geometry and laminate. A two-piece male mold was designed and machined to manufacture the wheel. Removable silicone inserts were used to create the hollow spokes.

Effect Of Material Viscoelasticity On Frequency Tuning Of Dielectric Elastomer Membrane Resonators, Liyang Tian

Electronic Thesis and Dissertation Repository

Dielectric elastomers (DEs) capable of large voltage-induced deformation show promise for applications such as resonators and oscillators. However, the dynamic performance of such vibrational devices is not only strongly affected by the nonlinear electromechanical coupling and material hyperelasticity, but also significantly by the material viscoelasticity. The material viscoelasticity of DEs originates from the highly mobile polymer chains that constitute the polymer networks of the DE. Moreover, due to the multiple viscous polymer subnetworks, DEs possess multiple relaxation processes. Therefore, in order to predict the dynamic performance of DE-based devices, a theoretical model that accounts for the multiple relaxation processes is …