Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- Blast (1)
- Cable-driven parallel manipulator (1)
- Cable-suspended robots (1)
- Cam (1)
- Center of mass balance system (1)
-
- Counterweights (1)
- Design (1)
- Drop down system (1)
- Dyanamic balancing (1)
- Dynamics (1)
- Engineering (1)
- Fiso (1)
- Fluid interactions (1)
- Gait (1)
- Kinematics (1)
- Knee (1)
- Kneeling (1)
- LESS (1)
- LabVIEW (1)
- MIS (1)
- Mechanical (1)
- Minimally Invasive Surgery (1)
- NOTES (1)
- Phenotyping (1)
- Prosthetic (1)
- RMIS (1)
- Rehabilitation (1)
- Remote sensing (1)
- Robotics (1)
- Shock tube (1)
Articles 1 - 5 of 5
Full-Text Articles in Applied Mechanics
Geometric Iteration Of A Knee Prosthetic And Static Stress-Bearing Capacity, Alexander Wheeler
Geometric Iteration Of A Knee Prosthetic And Static Stress-Bearing Capacity, Alexander Wheeler
Honors Theses
The purpose of this study was to improve a prosthetic knee model in terms of size, weight, and biocompatibility. Several tests were run to determine its effectiveness in supporting static and quasistatic loads. The positions in which these tests were run include static upright standing, static one-knee 90 degree kneeling, static squatting at maximum flexion, and quasistatic midstride. These simulations were conducted to find areas of high stress and strain. These patterns were used to determine the maximum body weight a physical prosthetic could support. The material used to create the prosthetic was changed from AISI 316 stainless steel to …
Cam-Based Pose-Independent Counterweighting For Partial Body-Weight Support In Rehabilitation, Ashish Shinde
Cam-Based Pose-Independent Counterweighting For Partial Body-Weight Support In Rehabilitation, Ashish Shinde
Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research
This thesis presents the design and testing of a body weight support system for gait training in a two-dimensional workspace. Extension of the system to a three-dimensional workspace is not within the scope of this thesis.
Gait dysfunctions are changes in normal walking patterns, often related to a disease or abnormality in different areas of the body. There are numerous body weight support (BWS) systems present in the market which are applied to rehabilitation scenarios in mobility recovery like in gait training. But most of these BWE systems are costly and generally are stationary devices. A major drawback of such …
Development Of The End-Effector Of A Cable-Driven Parallel Manipulator For Automated Crop Sensing, Iman Salafian
Development Of The End-Effector Of A Cable-Driven Parallel Manipulator For Automated Crop Sensing, Iman Salafian
Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research
A four cable-driven parallel manipulator (4CDPM), consisting of sophisticated spectrometers and imagers, is under development for use in acquiring phenotypic and environmental data over an acre-sized maize field. This thesis presents the design, controls, and testing of two sub-systems in a 4CDPM: a Center of Mass Balance System (CMBS) and a Drop-Down System (DDS).
One of the factors that influences stability is the center of mass (COM) position of the end effector. An offset in COM can cause a pendulum effect or an undesired tilt angle. A center of mass balancing system is presented in this thesis to minimize the …
Measurement And Description Of Dynamics Required For In Vivo Surgical Robotics Via Kinematic Methods, Jacob G. Greenburg
Measurement And Description Of Dynamics Required For In Vivo Surgical Robotics Via Kinematic Methods, Jacob G. Greenburg
Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research
With the goal of improved recovery times and reduced trauma to the patient there has been a substantial shift in the medical community’s demand for minimally invasive surgical (MIS) techniques. With the standardization of MIS becoming more commonplace in the medical field there are still many improvements that are desired. Traditional, manual methods of these surgeries require multiple incisions on the abdomen for the tools and instruments to be inserted. The more recent demand has been to localize the incisions into what is being referred to as a Laparoendoscopic Single-Site (LESS) surgery. Furthermore, the manual instruments that are commonly used …
A Shock Tube Technique For Blast Wave Simulation And Studies Of Flow Structure Interactions In Shock Tube Blast Experiments, Nicholas N. Kleinschmit
A Shock Tube Technique For Blast Wave Simulation And Studies Of Flow Structure Interactions In Shock Tube Blast Experiments, Nicholas N. Kleinschmit
Department of Engineering Mechanics: Dissertations, Theses, and Student Research
Improvised explosive devices (IED’s) are widely used against US and allied forces fighting in Iraq and Afghanistan. Exposure to IED blast may cause blast-induced traumatic brain injury (bTBI). The injury mechanisms are however not well understood. A critical need in bTBI-related research is the ability to replicate the loading conditions of IED blast waves in a laboratory environment. In this work, experimental studies have been carried out to explore the use of the shock tube technique for generating air shock waves that mimic the temporal and spatial characteristics of free-field blast waves and to investigate the blast wave-test sample interactions …