Mechanical Engineering Commons^™

Stability Of Ruddlesden-Popper Phase Lanthanum Nickelate As Air Electrode For Reversible Solid Oxide Cells, Daniel De Lorenzo Moreira

Graduate Theses, Dissertations, and Problem Reports

This thesis studied the long-term stability of Ruddlesden-Popper phase Lanthanum Nickelate under operating conditions as the air electrode for Reversible Solid Oxide Cells (R-SOC). Renewable energies have gone through increase in popularity throughout the last decades, mainly due to the consequences of the rapid population growth in the world. These new energies have been pointed as the rightful successor of fossil fuel energies in order to decrease the environmental impact of our day-to-day life. Solid Oxide Fuel Cells as well as Solid Oxide Electrolysis Cells are believed to be the key to stabilizing the energy supply when environmental conditions are …

System Analysis Of An Internal Combustion Engine (Ice) – Solid Oxide Fuel Cell (Sofc) Hybrid Cycle, Jose Javier Colon Rodriguez

Graduate Theses, Dissertations, and Problem Reports

Due to the intermittent nature of renewable energy and the rigid operation of existing coal plants, the need for flexible power generation technology is eminent. Hybrid energy systems have shown potential for flexible, grid following dynamics while maintaining higher efficiencies. The work below focuses on the performance analysis of a proposed 100 kW pressurized Internal Combustion Engine (ICE) and Solid Oxide Fuel Cell (SOFC) hybrid system. The un-utilized fuel from the SOFC stack provided the chemical energy to operate the engine. A turbocharger was used to deliver the necessary air flow for both the stack and engine. An external reformer …

Electrochemical Behaviors Of The Electrodes For Proton Conducting Intermediate Temperature Solid Oxide Fuel Cells (It-Sofc), Shichen Sun

FIU Electronic Theses and Dissertations

Proton conducting intermediate temperature (600oC-400oC) solid oxide fuel cells (IT-SOFC) have many potential advantages for clean and efficient power generation from readily available hydrocarbon fuels. However, it still has many unsolved problems, especially on the anode where the fuel got oxidized and the cathode where oxygen got reduced. In this study, for the anode, the effects of hydrogen sulfite (H2S) and carbon dioxide (CO2) as fuel contaminants were studied on the nickel (Ni) based cermet anode of proton conducting IT-SOFC using proton conducting electrolyte of BaZr0.1Ce0.7Y0.1Yb0.1O3 (BZCYYb). Both low-ppm level H2S and low-percentage level CO2 caused similar poisoning effects on …

Atomic Layer Deposition On Porous Materials: Problems With Conventional Approaches To Catalyst And Fuel Cell Electrode Preparation, Tzia Ming Onn, Rainer Küngas, Paolo Fornasiero, Kevin Huang, Raymond J. Gorte

Faculty Publications

Atomic layer deposition (ALD) offers exciting possibilities for controlling the structure and composition of surfaces on the atomic scale in heterogeneous catalysts and solid oxide fuel cell (SOFC) electrodes. However, while ALD procedures and equipment are well developed for applications involving flat surfaces, the conditions required for ALD in porous materials with a large surface area need to be very different. The materials (e.g., rare earths and other functional oxides) that are of interest for catalytic applications will also be different. For flat surfaces, rapid cycling, enabled by high carrier-gas flow rates, is necessary in order to rapidly grow thicker …

Exergy Study On The Effect Of Material Parameters And Operating Conditions On The Anode Diffusion Polarization Of The Sofc, Khalid Zouhri, Seong Young Lee

Michigan Tech Publications

In the presented work, a model is created in order to investigate the effect of different material parameters and operating conditions on the anode diffusion overpotential, which influence the exergy and energy efficiency of the solid oxide fuel cell (SOFC). In this research, it was demonstrated that the anode material parameters and operating conditions of the device components such as porosity, tortuosity, pore diameter, temperature, pressure and current density of the anode have various effects on the anode diffusion overpotential, which consequently affect the exergy and energy efficiency of the SOFC. The model has provided a strong direction on how …

Transient Analysis Of A Solid Oxide Fuel Cell/ Gas Turbine Hybrid System For Distributed Electric Propulsion, Venkata Adithya Chakravarthula

Browse all Theses and Dissertations

Gas turbine technology for aerospace applications are approaching limits in efficiency gains as increases in efficiency today occurs in very small increments. One limitation in conventional gas turbine technology is the combustion process, which destroys most of the exergy in the cycle. To address this limitation in a traditional Brayton power cycle, a hybrid system which is integrated with Solid Oxide Fuel Cell (SOFC) and gas turbine is developed. Hybrid systems involving fuel cells have better efficiencies than conventional power generation systems. Power generation systems with improved performance from low fuel utilizations and low maintenance costs are possible. The combination …

A Platinum Nanowire Network As A Highly Effective Current Collector For Intermediate Temperature Solid Oxide Fuel Cells, Hanping Ding, Xingjian Xue

Xingjian "Chris" Xue

We report the fabrication and evaluation of a platinum nanowire network as a highly efficient current collector for solid oxide fuel cells (SOFCs). The ink of carbon-black supported platinum nanoparticles was sprayed onto the cathode. After firing, the carbon black was oxidized and disappeared as carbon dioxide gas while the platinum nanoparticles connect with one another, forming a tree-branch-like nanowire network. The diameters of the nanowires range from 100 nm to 400 nm. Compared to a conventional platinum paste current collector, the polarization resistance of the PrBaCo₂O_5+δ (PBCO) cathode with a nanowire current collector was reduced …

A Platinum Nanowire Network As A Highly Effective Current Collector For Intermediate Temperature Solid Oxide Fuel Cells, Hanping Ding, Xingjian Xue

Xingjian "Chris" Xue

We report the fabrication and evaluation of a platinum nanowire network as a highly efficient current collector for solid oxide fuel cells (SOFCs). The ink of carbon-black supported platinum nanoparticles was sprayed onto the cathode. After firing, the carbon black was oxidized and disappeared as carbon dioxide gas while the platinum nanoparticles connect with one another, forming a tree-branch-like nanowire network. The diameters of the nanowires range from 100 nm to 400 nm. Compared to a conventional platinum paste current collector, the polarization resistance of the PrBaCo2O5+δ (PBCO) cathode with a nanowire current collector was reduced by 44% at 650 …

Rational Design Of Mixed Ionic And Electronic Conducting Perovskite Oxides For Solid Oxide Fuel Cell Anode Materials: A Case Study For Doped Srtio3, Suwit Suthirakun, Guoliang Xiao, Salai Ammal, Fanglin Chen, Hans-Conrad Zur Loye, Andreas Heyden

Salai C. Ammal

No abstract provided.

Preparation Of La0.8sr0.2ga0.83mg0.17o2.815 Powders By Microwave-Induced Poly(Vinyl Alcohol) Solution Polymerization, Yuling Zhai, Chang Ye, Feng Xia, Jianzhong Xiao, Lei Dai, Yifan Yang, Yongqian Wang

Dr. Chang Ye

A new and simple chemical route, named microwave-induced poly(vinyl alcohol) (PVA) solution polymerization, has been used to prepare fine, homogeneous and high-density pellets of purer La0.8Sr0.2Ga0.83Mg0.17O2.815 (denoted as LS0.2GM0.17). The effect of different contents of PVA as the polymeric carrier, was studied and we obtained an optimal amount of PVA (1.65:1 ratio of positively charged valences of the cations (Men+) to negatively charged hydroxyl (–OH−) groups of the organics), which could ensure homogenous distribution of the metal ions in the polymeric network structure and inhibit segregation. The behavior of the powder after calcination at different temperatures was studied. The PVA …

A Microwave-Induced Solution-Polymerization Synthesis Of Doped Lagao3 Powders, Yuling Zhai, Chang Ye, Jianzhong Xiao, Lei Dai

Dr. Chang Ye

A new method, called the microwave-induced solution-polymerization synthesis (denoted as MW), and the conventional Pechini (denoted as PH) method have been used to prepare powders of La0.8Sr0.2Ga0.83Mg0.17O2.815 (denoted as LS0.2GM0.17) and La0.8Sr0.2(Ga0.9Co0.1)0.83Mg0.17O2.815(denoted as LS0.2GCM0.17). A higher heating rate and a more homogenous heating manner without thermal gradients in the microwave oven resulted in a pure LSGCM powder after calcination at 1400 °C for 9 hours (h) and purer LSGM (6.2% secondary phases). The grain size of the pellets of the above two powders was 2–3 μm without segregation. The densities of LS0.2GM0.17/MW and LS0.2GCM0.17/MW pellets, sintered at 1400 °C for …

Synthesis And Characterization Of Sr-And Mg-Doped Lagao_3 Powders By Polyvinylpyrrolidone Microwave-Induced Solution Polymerization, Chang Ye, Yuling Zhai, Jian-Zhong Xiao

Dr. Chang Ye

A new chemical route,named microwave-induced polyvinylpyrrolidone(PVP) solution polymerization,has been used to prepare La0.8Sr0.2Ga0.83Mg0.17O2.815(denoted as LS0.2GM0.17) powder.The effect of different contents of PVP as the polymeric carrier was studied and we obtained the optimum amount of PVP,which could ensure the homogenous distribution of the metal ions in its polymeric network structure and inhibit their segregation from the solution.The behavior of the powder after calcination at different temperatures was studied.The PVP solution process consumed less organics compared with traditional Pechini process.Consequently,PVP was a more effective carrier in the preparation of LSGM.High heating rate and more homogenous heating manner without thermal gradient in …

Modeling Of Chemical-Mechanical Couplings In Anode-Supported Solid Oxide Fuel Cells And Reliability Analysis, Xinfang Jin, Xingjian Xue

Xingjian "Chris" Xue

Oxygen ionic transport in conducting ceramics is an important mechanism enabling solid oxide fuel cell (SOFC) technology. The multi-physicochemical processes lead to the fact that the distribution of oxygen vacancy site fraction is not uniform in a positive-electrode electrolyte negative-electrode (PEN) assembly. Different oxygen vacancy concentrations induce different volumetric expansion of ceramics, resulting in complicated chemical–mechanical coupling phenomena and chemical stress in SOFCs. In this research, a mathematical model is developed to study oxygen ionic transport induced chemical stress in an SOFC. The model is validated using experimental polarization curves. Comprehensive simulations are performed to investigate chemical stress distribution in …

La0.7Sr0.3Fe0.7Ga0.3O3-Δ As Electrode Material For A Symmetrical Solid Oxide Fuel Cell, Zhibin Yang, Yu Chen, Chao Jin, Guoliang Xiao, Minfang Han, Fanglin Chen

Fanglin Chen

In this research, La_0.7Sr_0.3Fe_0.7Ga_0.3O_3−δ (LSFG) perovskite oxide was successfully prepared using a microwave-assisted combustion method, and employed as both anode and cathode in symmetrical solid oxide fuel cells. A maximum power density of 489 mW cm⁻² was achieved at 800 °C with wet H₂ as the fuel and ambient air as the oxidant in a single cell with the configuration LSFG|La_0.8Sr_0.2Ga_0.83Mg_0.17O_3−δ|LSFG. Furthermore, the cells demonstrated good stability in H₂ and acceptable sulfur tolerance.

Study Of A Renewable Biomass Powered Sofc, Yunhui Gong, Andrew Chien, Zhengping Mao, Kevin Huang

Kevin Huang

The objective of this work is to explore a solution to utilize biomass carbon by a tubular solid oxide fuel cell integrated with an "in-situ" steam gasification reactor. Non-catalyzed and catalyzed coconut shell carbons were employed as solid fuels, which were directly converted to gaseous fuels to feed the SOFC operated at 800°. Single cells showed variable electrochemical performances according to the catalytic additives. Sample without catalysts exhibited low power density, while those with catalysts such as Fe₂O₃ and K₂CO₃ showed higher performances. The enhanced cell performance with catalysts was considered to be the …

La0.9−XCaXCe0.1Cro3−Δ As Potential Anode Materials For Solid Oxide Fuel Cells, Xihui Dong, Shuguo Ma, Kevin Huang, Fanglin Chen

Kevin Huang

No abstract provided.

Temperature-Dependent Residual Stresses In Plasma Sprayed Electrolyte Thin-Film On The Cathode Substrate Of A Solid Oxide Fuel Cell, Kevin Huang, H. Harter

Kevin Huang

No abstract provided.

La0.7Sr0.3Fe0.7Ga0.3O3-Δ As Electrode Material For A Symmetrical Solid Oxide Fuel Cell, Zhibin Yang, Yu Chen, Chao Jin, Guoliang Xiao, Minfang Han, Fanglin Chen

Faculty Publications

In this research, La_0.7Sr_0.3Fe_0.7Ga_0.3O_3−δ (LSFG) perovskite oxide was successfully prepared using a microwave-assisted combustion method, and employed as both anode and cathode in symmetrical solid oxide fuel cells. A maximum power density of 489 mW cm⁻² was achieved at 800 °C with wet H₂ as the fuel and ambient air as the oxidant in a single cell with the configuration LSFG|La_0.8Sr_0.2Ga_0.83Mg_0.17O_3−δ|LSFG. Furthermore, the cells demonstrated good stability in H₂ and acceptable sulfur tolerance.

Investigation Of The High-Temperature Redox Chemistry Of Sr2Fe1.5Mo0.5O6-Δ Via In Situ Neutron Diffraction, Daniel E. Bugaris, Jason P. Hodges, Ashfia Hug, W. Michael Chance, Andreas Heyden, Fanglin Chen, Hans-Conrad Zur Loye

Faculty Publications

Crystallographic structural changes were investigated for Sr₂Fe_1.5Mo_0.5O_6−δ, an electrode material for symmetric solid oxide fuel cells. The samples of this material were heated and cooled in wet hydrogen and wet oxygen atmospheres, to simulate the reducing and oxidizing conditions experienced under actual fuel cell operating conditions, and their structures and oxygen contents were determined using in situ powder neutron diffraction. The existence of a reversible tetragonal to cubic phase transition was established to occur between room temperature and 400 °C, both on heating and cooling in either oxygen or hydrogen. The …

A Platinum Nanowire Network As A Highly Effective Current Collector For Intermediate Temperature Solid Oxide Fuel Cells, Hanping Ding, Xingjian Xue

Faculty Publications

We report the fabrication and evaluation of a platinum nanowire network as a highly efficient current collector for solid oxide fuel cells (SOFCs). The ink of carbon-black supported platinum nanoparticles was sprayed onto the cathode. After firing, the carbon black was oxidized and disappeared as carbon dioxide gas while the platinum nanoparticles connect with one another, forming a tree-branch-like nanowire network. The diameters of the nanowires range from 100 nm to 400 nm. Compared to a conventional platinum paste current collector, the polarization resistance of the PrBaCo₂O_5+δ (PBCO) cathode with a nanowire current collector was reduced …

Influence Of Crystal Structure On The Electrochemical Performance Of A-Site-Deficient Sr1-SNb0.1Co0.9O3-Δ Perovskite Cathodes, Yinlong Zhu, Ye Lin, Xuan Shen, Jaka Sunarso, Wei Zhou, Shanshan Jiang, Dong Su, Fanglin Chen, Zongping Shao

Faculty Publications

The creation of A-site cation defects within a perovskite oxide can substantially alter the structure and properties of its stoichiometric analogue. In this work, we demonstrate that by vacating 2 and 5% of Asite cations from SrNb_0.1Co_0.9O_3-δ (SNC1.00) perovskites (Sr_1-sNb_0.1Co_0.9O_3-δ,s = 0.02 and 0.05; denoted as SNC0.98 and SNC0.95, respectively), a Jahn–Teller (JT) distortion with varying extents takes place, leading to the formation of a modified crystal lattice within a the perovskite framework. Electrical conductivity, electrochemical performance, chemical compatibility and microstructure of Sr_1-sNb_0.1Co …

Modeling Of Chemical-Mechanical Couplings In Anode-Supported Solid Oxide Fuel Cells And Reliability Analysis, Xinfang Jin, Xingjian Xue

Faculty Publications

Oxygen ionic transport in conducting ceramics is an important mechanism enabling solid oxide fuel cell (SOFC) technology. The multi-physicochemical processes lead to the fact that the distribution of oxygen vacancy site fraction is not uniform in a positive-electrode electrolyte negative-electrode (PEN) assembly. Different oxygen vacancy concentrations induce different volumetric expansion of ceramics, resulting in complicated chemical–mechanical coupling phenomena and chemical stress in SOFCs. In this research, a mathematical model is developed to study oxygen ionic transport induced chemical stress in an SOFC. The model is validated using experimental polarization curves. Comprehensive simulations are performed to investigate chemical stress distribution in …

Analysis Of A Fuel Cell Combustor In A Solid Oxide Fuel Cell Hybrid Gas Turbine Power System For Aerospace Application, Ryan R. Sinnamon

Browse all Theses and Dissertations

Over the last few years, fuel cell technology has significantly advanced and has become a mode of clean power generation for many engineering applications. Currently the dominant application for fuel cell technology is with stationary power generation. Very little has been published for applications on mobile platforms, such as unmanned aerial vehicles. With unmanned aerial vehicles being used more frequently for national defense and reconnaissance, there is a need for a more efficiency, longer endurance power system that can support the increased electrical loads onboard. It has already been proven by others that fuel cell gas turbine hybrid systems can …

Modeling Of Chemical-Mechanical Couplings In Solid Oxide Cells And Reliability Analysis, Xinfang Jin

Theses and Dissertations

Solid oxide fuel cell (SOFC) has been well demonstrated as a promising clean energy conversion technology. For practical applications, the SOFC systems should have both good electrochemical performance and high reliability. The SOFCs are usually operated under very aggressive conditions, e.g., high temperatures (600-1000oC) and extremely low oxygen partial pressures (anode electrode). These aggressive operating conditions could lead to a variety of material system degradations, imposing great challenges on meeting lifetime requirement of SOFC commercial applications. It is therefore essential to increase the understanding of fundamental SOFC degradation mechanisms.

The basic structure of SOFCs is a positive electrode-electrolyte-negative electrode (PEN) …

Micro Modeling Study Of Cathode/Electrolyte Interfacial Stresses For Solid Oxide Fuel Cells, Xinfang Jin, Xingjian Xue

Faculty Publications

Delamination of the cathode/electrolyte interface is an important degradation phenomenon in solid oxide fuel cells (SOFCs). While the thermal stress has been widely recognized as one of the major reasons for such delamination failures, the role of chemical stress does not receive too much attention. In this paper, a micro-model is developed to study the cathode/electrolyte interfacial stresses, coupling oxygen ion transport process with structural mechanics. Results indicate that the distributions of chemical stress are very complicated at the cathode/electrolyte interface and show different patterns from those of thermal stress. The maximum principal stresses take place at the cathode/electrolyte interface …

Atomic Layer Deposition On Porous Materials: Problems With Conventional Approaches To Catalyst And Fuel Cell Electrode Preparation, Tzia Ming Onn, Rainer Küngas, Paolo Fornasiero, Kevin Huang, Raymond J. Gorte

Faculty Publications

Atomic layer deposition (ALD) offers exciting possibilities for controlling the structure and composition of surfaces on the atomic scale in heterogeneous catalysts and solid oxide fuel cell (SOFC) electrodes. However, while ALD procedures and equipment are well developed for applications involving flat surfaces, the conditions required for ALD in porous materials with a large surface area need to be very different. The materials (e.g., rare earths and other functional oxides) that are of interest for catalytic applications will also be different. For flat surfaces, rapid cycling, enabled by high carrier-gas flow rates, is necessary in order to rapidly grow thicker …

Multi-Physicochemical Modeling Of Solid Oxide Fuel Cells And Electrolyzer Cells, Yuanyuan Xie

Theses and Dissertations

Multi-physicochemical models are developed for solid oxide fuel cells and electrolysis cells. The models describe the complicated transport processes of charge (electron/ion) conservation, mass/species conservation, momentum conservation, and energy conservation. Transport processes are coherently coupled with chemical reforming processes, surface elementary reaction processes, as well as electro-oxidation processes of both hydrogen and carbon monoxide. The models are validated with experimental data and utilized for fundamental mechanism studies of SOFCs fueled with different type of fuels, such as hydrogen, hydrocarbon, e.g., methane, H2S, and their mixtures. The fundamental mechanisms associated with syngas generation using electrolysis cell are also extensively investigated using …

High Performance Low Temperature Solid Oxide Fuel Cells With Novel Electrode Architecture, Yu Chen, Qian Liu, Zhibin Yang, Fanglin Chen, Minfang Han

Faculty Publications

In this study, we have fabricated high performance low temperature solid oxide fuel cells (LT-SOFCs) with both acicular anodes and cathodes with thin Gd-doped ceria (GDC) electrolyte film. The acicular Ni-Gd_0.1Ce_0.9O_2−δ (Ni-GDC) anode was prepared using freeze drying tape casting, while the hierarchically porous cathode with nano-size Sm_0.5Sr_0.5CoO₃ (SSC) particles covering an acicular GDC skeleton was prepared by a combination of freeze drying tape casting and self-rising approaches. The acicular electrodes with 5–200 μm pores/channels enhance mass transport, while SSC particles of about 50 nm in the cathode promote …

Sr2Fe1.5Mo0.5O6-Δ – Sm0.2Ce0.8O1.9 Composite Anodes For Intermediate-Temperature Solid Oxide Fuel Cells, Beibei He, Ling Zhao, Shuxiang Song, Tong Liu, Fanglin Chen, Changrong Xia

Faculty Publications

Sr₂Fe_1.5Mo_0.5O_6−δ (SFM) perovskite is carefully investigated as an anode material for solid oxide fuel cells with LaGaO₃-based electrolytes. Its electronic conductivity under anodic atmosphere is measured with four-probe method while its ionic conductivity is determined with oxygen permeation measurement. Samaria doped ceria (SDC) is incorporated into SFM electrode to improve the anodic performance. A strong relation is observed between SDC addition and polarization losses, suggesting that the internal SFM-SDC contacts are active for H₂ oxidation. The best electrode performance is achieved for the composite with 30 wt% SDC addition, resulting …

Characteristics Of The Hydrogen Electrode In High Temperature Steam Electrolysis Process, Chao Jin, Chenghao Yang, Fanglin Chen

Faculty Publications

YSZ-electrolyte supported solid oxide electrolyzer cells (SOECs) using LSM-YSZ oxygen electrode but with three types of hydrogen electrode, Ni–SDC, Ni–YSZ and LSCM–YSZ have been fabricated and characterized under different steam contents in the feeding gas at 850°C. Electrochemical impedance spectra results show that cell resistances increase with the increase in steam concentrations under both open circuit voltage and electrolysis conditions, suggesting that electrolysis reaction becomes more difficult in high steam content. Pt reference electrode was applied to evaluate the contributions of the hydrogen electrode and oxygen electrode in the electrolysis process. Electrochemical impedance spectra and over potential of both electrodes …