Mechanical Engineering Commons^™

The Influence Of Mixing Duct Length And Phase Of Flight On Wall Temperatures Of A Rocket Based Combined Cycle Engine In Ejector And Air-Augmented Modes, Jonathan Grow

Doctoral Dissertations and Master's Theses

Rocket Based Combined Cycle (RBCC) engines have been theorized as a possible means of powering launch vehicles and high-speed atmospheric vehicles. By incorporating aspects of both air-breathing and rocket propulsion, RBCC engines promise up to a 230 % increase in specific impulse over traditional chemical rocket propulsion by entraining a secondary flow of atmospheric air and mixing it with the exhaust of a rocket motor. Students within the Embry-Riddle Future Space Explorers and Developers Society (ERFSEDS) identified a
problem of excessive heating and structural failure of the mixing duct during launch and transonic flight of a student-built flight test vehicle. …

Nasa Student Launch - Payload, Eli Kirk

All Undergraduate Projects

A team of mechanical engineering, physics, and computer science students from Central Washington University have constructed a fully functional subscale model rocket to be flown at the NASA Student Launch competition. The rocket’s payload was designed to open the nose cone and take a photo of the rocket’s surroundings after descending from the launch. Smaller parts were constructed through machining and 3D printing that will be added to the purchased major component, the linear actuator, in order to perform the required tasks. These tasks are signaled by an attached electronics board, which will receive an RF command remotely, execute code, …

Nasa Student Rocket Launch, Ethan Stapleton

All Undergraduate Projects

The Rocketry Payload team consisting of Kallysta, Eli and Ethan needed to build a payload that flew in a rocket also built by the team. After the rocket has landed, a camera is deployed outside the rocket through a 3-inch gap created by a linear actuator. The camera must rotate 360 degrees and take photos of the surrounding area. The entire system must weigh less than 4.4 pounds as well. The team designed this system using their knowledge obtained through the Mechanical Engineering program at Central Washington University. It was important for them to keep in mind that the system …

Evaluation And Implementation Of Lean Engineering Principles For Improving A University Rocket Team, Alan Garcia

Open Access Theses & Dissertations

In the present day, lean is a tool applied to manufacturing industries trying to reduce wasteand non-value-added work to every process during the supply chain. While implementing lean thinking in the industry has been highly effective, it is less common for academic purposes. However, it can also improve performance if the concept is correctly applied. The purpose of this thesis is to show and analyze the application of Lean Engineering thinking and its six principles to the Sun City Summit Rocket Team from the University of Texas at El Paso which competed in the Intercollegiate Rocket Engineering Competition (IREC) Spaceport …

Rocket Motor Nozzle, Corey Hillegass

Williams Honors College, Honors Research Projects

For this honors research and senior design project, the authors will research, analyze, and manufacture a rocket motor nozzle for the Akronauts rocket design team. This research and design project will improve how the rocket design team will decide and manufacture nozzles going forward. The impact of this improvement allows the rocket design team to take steps toward being self-sustaining by manufacturing student designed parts as opposed to commercially bought parts. This will not only be successful in increasing student impact on future designs, but also provides a technical challenge for the authors and will present as an impressive feat …

Structural Design Of Thrust Measurement System For Cryogenic Rocket Engines, Abner Jael Moreno Tarango

Open Access Theses & Dissertations

The Center for Space Exploration and Technology Research (cSETR) at The University of Texas at El Paso (UTEP) has been the leader in academia on the development of Liquid Oxygen (LO2) and Liquid Methane (LCH4) propulsion technologies. One of the projects being developed at cSETR is a suborbital vehicle whose mission is to evaluate performance parameters, demonstrate restart capability, and demonstrate the propulsion system operation in microgravity. This vehicle, called Daedalus, will use a 500-lbf LO2-LCH4 rocket engine that can be throttled down to 100-lbf. To accomplish this goal, UTEP partnered with the El Paso County to lease a plot …

Design Of Shape-Conforming Nosecone For Optimal Fluid Flow From Transonic To Supersonic Range, Anna Tombazzi

Williams Honors College, Honors Research Projects

Modern flight vehicles, such as rockets, missiles, and airplanes, experience a force caused by forebody wave drag during the flight. This drag force is induced when the frontal point of each vehicle breaks the pressure wave during flight. Efforts to reduce this wave drag force to improve flight efficiency include modifying the nosecone profile of the flight vehicles to lower the drag force.

This project revolved around creating a design to make the transformation of nosecone shapes from a ¾ Parabolic profile to a ½ Power Series profile possible, mid-flight. Using a novel nosecone assembly, shape memory alloys (SMAs) and …

Development And Integration Of The Janus Robotic Lander: A Liquid Oxygen - Liquid Methane Propulsion System Testbed, Raul Ponce

Open Access Theses & Dissertations

Initiatives have emerged with the goal of sending humans to other places in our solar system. New technologies are being developed that will allow for more efficient space systems to transport future astronauts. One of those technologies is the implementation of propulsion systems that use liquid oxygen and liquid methane (LO2-LCH4) as propellants.

The benefits of a LO2-LCH4 propulsion system are plenty. One of the main advantages is the possibility of manufacturing the propellants at the destination body. A space vehicle which relies solely on liquid oxygen and liquid methane for its main propulsion and reaction control engines is necessary …

Design Of A 2000 Lbf Lox/Lch4 Throttleable Rocket Engine For A Vertical Lander, Israel Lopez

Open Access Theses & Dissertations

Liquid oxygen (LOX) and liquid methane (LCH4) has been recognized as an attractive rocket propellant combination because of its in-situ resource utilization (ISRU) capabilities, namely in Mars. ISRU would allow launch vehicles to carry greater payloads and promote missions to Mars. This has led to an increasing interest to develop spacecraft technologies that employ this propellant combination.

The UTEP Center for Space Exploration and Technology Research (cSETR) has focused part of its research efforts to developing LOX/LCH4 systems. One of those projects includes the development of a vertical takeoff and landing vehicle called JANUS. This vehicle will employ a LOX/LCH4 …

Throttleable Gox/Abs Launch Assist Hybrid Rocket Motor For Small Scale Air Launch Platform, Zachary S. Spurrier

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The ability for an aircraft-based launch platform to place an orbital payload onto a nominal launch trajectory at a higher energy state -- altitude, velocity, flight path angle, and azimuth --using highly-efficient air breathing propulsion instead of a much lower-efficiency rocket system, offers the potential for a significantly smaller launch vehicle. An airborne platform also provides the ability to launch from multiple locations and allows for significantly increased "system responsiveness." The NASA Armstrong Flight Research Center’s Towed Glider Air-Launch System (TGALS) is a small-scale flight research project investigating the feasibility for a remotely-piloted, towed, glider system to act as a …

Design Of A 500 Lbf Liquid Oxygen And Liquid Methane Rocket Engine For Suborbital Flight, Jesus Eduardo Trillo

Open Access Theses & Dissertations

Liquid methane (LCH4)is the most promising rocket fuel for our journey to Mars and other space entities. Compared to liquid hydrogen, the most common cryogenic fuel used today, methane is denser and can be stored at a more manageable temperature; leading to more affordable tanks and a lighter system. The most important advantage is it can be produced from local sources using in-situ resource utilization (ISRU) technology. This will allow the production of the fuel needed to come back to earth on the surface of Mars, or the space entity being explored,making the overall mission more cost effective by enabling …

Design Of The Structural And Propulsion Systems For The 2015 University Of Akron Rocket Team, Kyle W. Dehoff, Nicholas J. Hrusch

Williams Honors College, Honors Research Projects

No abstract provided.

A Numerical Study Of High Temperature And High Velocity Gaseous Hydrogen Flow In A Cooling Channel Of A Ntr Core, Sajan B. Singh

University of New Orleans Theses and Dissertations

Two mathematical models (a one and a three-dimensional) were adopted to study, numerically, the thermal hydrodynamic behavior of flow inside a single cooling channel of a Nuclear Thermal Rocket (NTR) engine. The first model assumes the flow in the cooling channel to be one-dimensional, unsteady, compressible, turbulent, and subsonic. The working fluid (GH₂) is assumed to be compressible. The governing equations of the 1-D model are discretized using a second order accurate finite difference scheme. Also, a commercial CFD code is used to study the same problem. Numerical experiments, using both codes, simulated the flow and heat transfer …

Rocket Fuel Pressurization, Sean Green, Joe Marcinkowski, Andrew Nahab

Mechanical Engineering

No abstract provided.

Closed-Loop Thrust And Pressure Profile Throttling Of A Nitrous Oxide/Hydroxyl-Terminated Polybutadiene Hybrid Rocket Motor, Zachary W. Peterson

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Hybrid motors that employ non-toxic, non-explosive components with a liquid oxidizer and a solid hydrocarbon fuel grain have inherently safe operating characteristics. The inherent safety of hybrid rocket motors offers the potential to greatly reduce overall operating costs. Another key advantage of hybrid rocket motors is the potential for in-flight shutdown, restart, and throttle by controlling the pressure drop between the oxidizer tank and the injector. This research designed, developed, and ground tested a closed-loop throttle controller for a hybrid rocket motor using nitrous oxide and hydroxyl-terminated polybutadiene as propellants. The research simultaneously developed closed-loop throttle algorithms and lab scale …

Rayleigh Test Apparatus Design Report, Josef Duller, Owen Raybould, James Nicovich

Mechanical Engineering

The Rayleigh Test Apparatus is a device that will be used to test the thermodynamic properties of Nitrous Oxide to assess the feasibility of using this fluid as a coolant for a hybrid rocket aero spike. The aero spike is intended to redirect the propulsion flow as it leaves the engine to create a more efficient flow pattern at low and high altitudes. However, there are issues of overheating which leads to melting of the aero spike. For this reason, the use of nitrous oxide (N2O) as a coolant is being explored. N20 is being considered because it is already …

Effect Of Unsteady Combustion On The Stability Of Rocket Engines, Tina Morina Rice

Doctoral Dissertations

Combustion instability is a problem that has plagued the development of rocket-propelled devices since their conception. It is characterized by the occurrence of high-frequency nonlinear gas oscillations inside the combustion chamber. This phenomenon degrades system performance and can result in damage to both structure and instrumentation.

The goal of this dissertation is to clarify the role of unsteady combustion in the combustor instability problem by providing the first quantified estimates of its effect upon the stability of liquid rocket engines. The combination of this research with a new system energy balance method, accounting for all dynamic interactions within a system, …

High-Level, Product Type-Specific Programmatic Operations For Streamlining Associative Computer-Aided Design, Nathan W. Scott

Theses and Dissertations

Research in the field of Computer Aided Design (CAD) has long focused on reducing the time and effort required of engineers to define three dimensional digital product models. Parametric, feature-based modeling with inter-part associativity allows complex assembly designs to be defined and re-defined while maintaining the vital part-to-part interface relationships. The top-down modeling method which uses assembly level control structures to drive child level geometry has proved valuable in maintaining these interfaces. Creating robust parametric models like these, however, is very time consuming especially since there can be hundreds of features and thousands of mathematical expressions to create. Even if …

High Pressure Testing Of Composite Solid Rocket Propellant Mixtures: Burner Facility Characterization, Rodolphe Valentin Carro

Electronic Theses and Dissertations

Much Research on composite solid propellants has been performed over the past few decades and much progress has been made, yet many of the fundamental processes are still unknown, and the development of new propellants remains highly empirical. Ways to enhance the performance of solid propellants for rocket and other applications continue to be explored experimentally, including the effects of various additives and the impact of fuel and oxidizer particle sizes on burning behavior. One established method to measure the burning rate of composite propellant mixtures in a controlled laboratory setting is to use a constant-volume pressure vessel, or strand …

Design And Implementation Of An Emission Spectroscopy Diagnostic In A High-Pressure Strand Burner For The Study Of Solid Propell, Jason Arvanetes

Electronic Theses and Dissertations

The application of emission spectroscopy to monitor combustion products of solid rocket propellant combustion can potentially yield valuable data about reactions occurring within the volatile environment of a strand burner. This information can be applied in the solid rocket propellant industry. The current study details the implementation of a compact spectrometer and fiber optic cable to investigate the visible emission generated from three variations of solid propellants. The grating was blazed for a wavelength range from 200 to 800 nm, and the spectrometer system provides time resolutions on the order of 1 millisecond. One propellant formula contained a fine aluminum …