Mechanical Engineering Commons^™

Development Of A 2d Scr Catalyst On A Diesel Particulate Filter Model For Design And Control Applications To A Ultra Low Nox Aftertreatment System, Venkata Chundru

Dissertations, Master's Theses and Master's Reports

This research focuses on modeling and control of PM and NO_x in diesel engine exhaust using an SCR catalyst on a Diesel Particulate Filter (SCR-F). A 2D SCR-F model was developed that is capable of predicting internal states: 2D temperature, PM and NH₃storage distributions and filtration efficiency, pressure drop, PM mass retained in the PM cake and substrate wall and outlet NO, NO₂and NH₃concentrations. The SCR-F model was used to simulate a DOC + SCR-F + DOC + SCR ultra-low NOx system that can achieve > 99.5% NOx conversion efficiency.

The model was calibrated …

Physical Modeling Of Lithium-Ion Aging For Automotive Applications, Anurag Kamal

Dissertations, Master's Theses and Master's Reports

This thesis extends the full-scale electrochemical model for a Lithium-ion battery based on the porous electrode theory to incorporate aging mechanisms of solid electrolyte interface formation, cyclic electrode degradation, and lithium plating during overcharge, automotive vibrations, mechanical stress, and cell temperature, as reported in the existing literature. Further, the thesis presents the scope of the parameters used in the model to enable designers to extend the equations for new mechanisms and variability of other parameters.

An increased set of equations makes the complexity of the model even higher, and it would be very computationally complex to simulate this model. This …

The Influence Of Bmss On The Characterization And Modeling Of Series And Parallel Li-Ion Packs, Sandra Castano-Solis, Daniel Serrano-Jimenez, Lucia Gauchia, Javier Sanz

Michigan Tech Publications

This work analyzes the effects of a BMS (battery management system) on the characterization and modeling of series and parallel connections of Li-ion cell packs. The Li-ion pack studied consists of four series modules connected in parallel. This pack has been characterized by means of charge, discharge and frequency tests. As a result of these tests, series and parallel influence on battery parameters have been determined. A model considering the effects of a BMS is established and compared with a model based on a single-cell approach. Experimental validations show that the single cell based approach gives poor results in comparison …

An Experimental Investigation Of The Effect Of Temperature And Space Velocity On The Performance Of A Cu-Zeolite Flow-Through Scr And A Scr Catalyst On A Dpf With And Without Pm Loading, Vaibhav Kadam

Dissertations, Master's Theses and Master's Reports

Abstract The heavy-duty diesel (HDD) engines use the diesel oxidation catalyst (DOC), catalyzed particulate filter (CPF) and urea injection based selective catalytic reduction (SCR) systems in sequential combination, to meet the US EPA 2010 PM and NOₓ emission standards. The SCR along with a NH₃ slip control catalyst (AMOX) offer NOₓ reduction >90 % with NH₃ slipHowever, there is a strong desire to further improve the NOₓ reduction performance of such systems, to meet the California Optional Low NOₓ Standard implemented since 2015. Integrating SCR functionality into a diesel particulate filter (DPF), by coating the SCR catalyst on the DPF, …

Molecular Modeling Of Epon 862-Detda / Carbon Composites, Cameron Hadden

Dissertations, Master's Theses and Master's Reports - Open

The thermoset epoxy resin EPON 862, coupled with the DETDA hardening agent, are utilized as the polymer matrix component in many graphite (carbon fiber) composites. Because it is difficult to experimentally characterize the interfacial region, computational molecular modeling is a necessary tool for understanding the influence of the interfacial molecular structure on bulk-level material properties. The purpose of this research is to investigate the many possible variables that may influence the interfacial structure and the effect they will have on the mechanical behavior of the bulk level composite. Molecular models are established for EPON 862-DETDA polymer in the presence of …

Understanding Chassis Inputs From The Rear Suspension Of A Snowmobile, Jamie L. Kleinendorst

Dissertations, Master's Theses and Master's Reports - Open

Today’s snowmobile industry faces great challenges in the field of noise & vibration. The area of main concern is the pass-by noise restriction defined by the Society of Automotive Engineers (SAE) test standard J192, with a maximum sound pressure level of 78 dB(A) being required by many states and national parks. To continue meet or beat this requirement without effecting machine performance, a deeper understanding of the sound transfer paths is required. This thesis examines the transfer paths created by the tunnel, rear suspension, drive shaft, and rubber composite track, with the primary source being suspension input through the ground. …

Development Of An In Situ Measurement Device For Obtaining Material Thermal Properties, Mark A. Hepokoski

Dissertations, Master's Theses and Master's Reports - Open

This thesis presents a methodology for measuring thermal properties in situ, with a special focus on obtaining properties of layered stack-ups commonly used in armored vehicle components. The technique involves attaching a thermal source to the surface of a component, measuring the heat flux transferred between the source and the component, and measuring the surface temperature response. The material properties of the component can subsequently be determined from measurement of the transient heat flux and temperature response at the surface alone. Experiments involving multilayered specimens show that the surface temperature response to a sinusoidal heat flux forcing function is also …