Open Access. Powered by Scholars. Published by Universities.®
- Institution
Articles 1 - 5 of 5
Full-Text Articles in Mechanical Engineering
The Development Of A Primer Payload With Microparticles For Uti Pathogen Identification Using Polythymidine- Modified Lamp Primers In Droplet Lamp, Jonas Otoo
KGI Theses and Dissertations
Nucleic acid amplification tests (NAATs) are among the diagnostic tests with the highest sensitivity and specificity. However, they are more complex to develop than other diagnostic tests such as biochemical tests and lateral flow immunoassay tests. Polymerase chain reaction (PCR) is the gold standard for NAATs. PCR requires thermal cycling to achieve clonal amplification of the target pathogen DNA for diagnosis. Thermal cycling poses a challenge in the development of PCR diagnostics for point-of-care (POC) settings. Loop-mediated isothermal amplification (LAMP) offers an isothermal method for NAATs diagnostics. The advancement of the microfluidics field significantly enhances the development of LAMP diagnostics …
The Study Of 3d Micro-Fluid Printing In Aqueous Two-Phase System, Mian Huang
The Study Of 3d Micro-Fluid Printing In Aqueous Two-Phase System, Mian Huang
Dissertations and Theses
Aqueous two-phase system (ATPS) is a technology that allows phase separation in an aqueous environment. This technology can be used for the separation, extraction and purification of a variety of biomolecules and thus gained great attention in industry and academia. This thesis is a combination of ATPS, 3D printing, and microfluidics technologies and realizes the printing of biocompatible aqueous structures in another aqueous matrix. The objectives of this thesis include 1) customizing a regular thermal extrusion 3D printer for printing 3D aqueous structures, 2) printing 3D aqueous structure in an aqueous matrix, and 3) studying the stability of the printed …
Turbulent Mixers For Protein Folding Experiments, Venkatesh Inguva
Turbulent Mixers For Protein Folding Experiments, Venkatesh Inguva
Doctoral Dissertations
Protein folding studies require the development of micro-mixers that require less sample, mix at faster rates, and still provide a high signal to noise ratio. Chaotic to marginally turbulent micro-mixers are promising candidates for this application. In this study, various turbulence and unsteadiness generation concepts are explored that avoid cavitation. The mixing enhancements include flow turning regions, flow splitters, and vortex shedding. The relative effectiveness of these different approaches for rapid micro-mixing is discussed. Simulations found that flow turning regions provided the best mixing profile. Various turbulence models are simulated to determine appropriate model of the design requirements. Experimental validation …
Development Of Microdialysis Probes In Series Approach Toward Eliminating Microdialysis Sampling Calibration: Miniaturization Into A Pdms Microfluidic Device, Randy Espinal Cabrera
Development Of Microdialysis Probes In Series Approach Toward Eliminating Microdialysis Sampling Calibration: Miniaturization Into A Pdms Microfluidic Device, Randy Espinal Cabrera
Graduate Theses and Dissertations
A new microdialysis sampling method and microfluidic device were developed in vitro. The method consisted of using up to four microdialysis sampling probes connected in series to evaluate the relative recovery (RR) of different model solutes methyl orange, fluorescein isothiocyanate (FITC)-dextran average mol. wt. 4,000 (FITC-4), FITC-10, FITC-20, and FITC-40. Different flow rates (0.8, 1.0, and 1.5 µL/min) were used to compare experimentally observed relative recoveries with theoretical estimations. With increasing the number of probes in series, the relative recovery increases and ~100% (99.7% ± 0.9%) relative recovery for methyl orange was obtained. For larger molecules such as fluorescein isothiocyanate …
Design, Fabrication, And Testing Of A 3d Printer Based Microfluidic System, Carlton A. Mcmullen
Design, Fabrication, And Testing Of A 3d Printer Based Microfluidic System, Carlton A. Mcmullen
Graduate Theses and Dissertations
A pneumatically actuated PDMS based microfluidic devices were designed and fabricated by soft-lithography. Two types of molds were fabricated out of different material for this experiment. The first mold, (device 1), was fabricated from a sheet of Polymethyl methacrylate (PMMA) material, similar to Plexiglas. The device features were micro-engraved onto the face of the material. The second mold, (device 2), was fabricated from the use of fused deposition modeling (FDM) 3D printing. The pumping efficiency of the PDMS devices was analyzed through the characterization of the micro-pumps flowrate with respect to the pumps driving pressure and the actuation frequency. Tested …