Mechanical Engineering Commons^™

Stabilization Trajectory And Recovery System For High Altitude Weather Balloon Payloads (S.T.A.R.), Robert Canalas, Aaron Juan, Miles Nguyen, James Oblitas, Anne Paloma

Mechanical Engineering Senior Theses

Of the 657,000 global balloon launches each year, only 20% of payloads are recovered, leading to unsustainable business and environmental practices. This paper details the development and evaluation of the S.T.A.R. (Stabilization, Trajectory, and Recovery) system, which increases the recovery rate of weather balloon sensors by enabling ideal landing conditions. System testing concludes that S.T.A.R. is capable of housing weather sensors in a fully controllable glider capable of targeted landing. If properly scaled up and redesigned for mass production, the S.T.A.R. system increases weather-sensing equipment recovery for weather-reporting institutions around the world. Although the featured iterations consist of basswood, carbon …

Finite Element Analysis Of 3d-Printed Pcl Scaffolds, Ireolu K. Orenuga, Joao Soares, Phillip D. Glass, Daeha Joung Ph.D.

Undergraduate Research Posters

Finite Element Analysis of 3D-printed PCL Scaffolds for Synergizing Cellular Micro-Environment and Mechanical Stimuli to Enhance Engineered Tissue Growth in Vitro

Ireolu Orenuga,1 Phillip Glass,2 Daeha Joung,2 Joao S. Soares1

1. Department of Mechanical and Nuclear Engineering, College of Engineering, Virginia Commonwealth University
2. Department of Physics, College of Humanities & Sciences, Virginia Commonwealth University

Introduction: Tissue engineering aims to create viable and functional engineered tissues via biodegradable scaffolds and autologous cells. Scaffolds play an essential part in organizing the architecture of developing tissues and aid in the proper function of implants acutely by serving as mechanical support and long-term by …

Fabrication Of Hard–Soft Microfluidic Devices Using Hybrid 3d Printing, Carlos Ruiz, Karteek Kadimisetty, Kun Yin, Michael G. Mauk, Hui Zhao, Changchun Liu

Mechanical Engineering Faculty Research

Widely accessible, inexpensive, easy-to-use consumer 3D printers, such as desktop stereolithography (SLA) and fused-deposition modeling (FDM) systems are increasingly employed in prototyping and customizing miniaturized fluidic systems for diagnostics and research. However, these 3D printers are generally limited to printing parts made of only one material type, which limits the functionality of the microfluidic devices without additional assembly and bonding steps. Moreover, mating of different materials requires good sealing in such microfluidic devices. Here, we report methods to print hybrid structures comprising a hard, rigid component (clear polymethacrylate polymer) printed by a low-cost SLA printer, and where the first printed …

Construction Of A Hyperspectral Imager Using 3d-Printed And Off-The-Shelf Components, Joshua Moorhouse

Mechanical Engineering Undergraduate Honors Theses

The Arkansas Center for Space and Planetary Sciences is working in collaboration with the Mechanical Engineering department to create a relatively cheap and modifiable hyperspectral imager. It is constructed using 3D-printed and off-the-shelf components from Edmund Optics and Amazon. The iteration created in this paper delivers spectrograms in the visible spectrum. The long-term goals of the camera are to create hyperspectral images from these spectrograms and to advance the imager into the infrared and near-infrared spectra. This imager is being developed to be used in the Arkansas Center for Space and Planetary Sciences environmental test chambers to further the scientific …

Construction Of A Hyperspectral Camera Using Off-The-Shelf Parts And 3d-Printed Parts, Connor Heo

Mechanical Engineering Undergraduate Honors Theses

The Arkansas Center for Space and Planetary Sciences (ACSPS) is working together with the Mechanical Engineering Department to build a modifiable camera with 3D-printed parts and off-the-shelf parts (sourced from Edmund Optics and Amazon). The design is to be readily changeable, primarily with the 3D printed parts, as to accommodate new ideas and functionalities in the future. Ultimately, the camera should be relatively cheap while maintaining functionality for proposed use cases. Earlier versions of the design will be tested extensively and rapidly updated in the ACSPS labs with benchtop testing. This will involve subjects with both visible and infrared emissions, …

Design And Analysis Of A 3d-Printed, Thermoplastic Elastomer (Tpe) Spring Element For Use In Corrective Hand Orthotics, Kevin Thomas Richardson

Theses and Dissertations--Mechanical Engineering

This thesis proposes an algorithm that determine the geometry of 3D-printed, custom-designed spring element bands made of thermoplastic elastomer (TPE) for use in a wearable orthotic device to aid in the physical therapy of a human hand exhibiting spasticity after stroke. Each finger of the hand is modeled as a mechanical system consisting of a triple-rod pendulum with nonlinear stiffness at each joint and forces applied at the attachment point of each flexor muscle. The system is assumed quasi-static, which leads to a torque balance between the flexor tendons in the hand, joint stiffness and the design force applied to …

Mechanical Testing Of Fused Filament 3-D Printed Components For Distributed Manufacturing, Nagendra Gautam Tanikella

Dissertations, Master's Theses and Master's Reports

Fused filament fabrication (FFF)-based open-source 3-D printers offer the potential of decentralized manufacturing both in developing and developed countries. Unfortunately, a severe lack of data and standards relating to material properties and printed components limit this potential. This thesis first investigates the mechanical properties of a wide-range of FFF materials and provides a database of mechanical strength of the materials tested. The results demonstrate that the tensile strength of a 3-D printed specimen depends largely on the mass of the specimen, which provides a means to estimate the strength of 3-D printed components. Then this information is used to evaluate …