Mechanical Engineering Commons^™

Experimental Methods And Practices For The Study Of Toroidal Inflated, Braided Fabric Members, Daniel J. Whitney

Electronic Theses and Dissertations

Inflatable structures have become a very important area of interest for many differing applications where lightweight packable structures are required. NASA is developing Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology that takes advantage of stacked, inflated fabric tori to form a decelerating spacecraft nose cone. The tori consist of a bladder, braided fabric shell, and reinforcing in the form of integral cords or externally bonded straps. The focus of this thesis is on the development of methods for the structural testing of inflated fabric tori and developing an enhanced understanding of their behavior. This is essential for providing insight into the …

Final Design Report: Allergen Mixing Assistant (Ama) Micro-Refrigeration Redesigning, Mitchell Parks, Minwoo (Michael) Suh

Mechanical Engineering

Abstract

Allergen Mixing Assistant (AMA) by Xtract Solutions is a device designed to more “effectively refrigerate, organize, and mix allergenic extracts”. Although Xtract Solutions intended the product to be fully automated, the company has decided against its automation and declared its current design as a minimum viable product whose components are too expensive, difficult to source and complex. Therefore, Cal Poly AMA design team - Mitchell Parks and Minwoo Suh - has decided to replace these expensive components with much more economical alternatives as shown below:

Stirling cooler

→

Thermoelectric (Peltier) cooler

Custom Arduino

Controller Card

→

TEC Thermostat *** …

Final Design Report: Grasp Data Acquisition Project Axon Vr, Michael Erberich, Jack Schultz, Tyler Yeaman

Mechanical Engineering

No abstract provided.

Application Of Floating Pedal Regenerative Braking For A Rear-Wheel-Drive Parallel-Series Plug-In Hybrid Electric Vehicle With An Automatic Transmission, Dylan Lewis Lewton

Doctoral Dissertations and Master's Theses

As the world continues to move further away from our reliance on fossil fuels, hybrid vehicles are becoming ever more popular. Braking is a system on both hybrid and normal vehicles that involves a significant amount of power and energy. A hybrid can recapture some of that energy using regenerative braking. In this thesis, a method is devised to blend hydraulic and regenerative braking in the most effective manner. A MATLAB Simulink model was built to simulate a parallel-series plug-in hybrid electric vehicle. The model allows for the implementation of a regenerative brake controller that utilizes floating pedal regen, custom …

Multi-Classifier Fusion Strategy For Activity And Intent Recognition Of Torso Movements, Abhijit Kadrolkar

Doctoral Dissertations

As assistive, wearable robotic devices are being developed to physically assist their users, it has become crucial to develop safe, reliable methods to coordinate the device with the intentions and motions of the wearer. This dissertation investigates the recognition of user intent during flexion and extension of the human torso in the sagittal plane to be used for control of an assistive exoskeleton for the human torso. A multi-sensor intent recognition approach is developed that combines information from surface electromyogram (sEMG) signals from the user’s muscles and inertial sensors mounted on the user’s body. Intent recognition is implemented by following …

A Lower Limb Prosthesis With Active Alignment For Reduced Limb Loading, Andrew Lapre

Doctoral Dissertations

Over the past decade, the growing field of robotics has created new possibilities in lower limb prostheses. The focus of these new prostheses has been replicating the dynamics of the lost limb in order to restore gait of individuals with lower limb amputations to healthy norms. This places demanding loads on the residual limb. Compensation by the rest of body is high, causes overloading of intact joints and can lead to deterioration of mobility and overall health. Abnormalities remain present in the person’s gait, stemming from the loading of soft tissue and the altered anatomy of the affected limb. In …

A Soft Multiple-Degree Of Freedom Load Cell Based On The Hall Effect, Qiandong Nie

Masters Theses

The goal of this thesis is to develop a soft multiple-degree-of-freedom (multi-DOF) load cell that is robust and light weight for use in robotics applications to sense three axes of force and a single axis of torque. The displacement of the magnet within the elastomer changes the magnetic flux density which is sensed by two 3-axis Hall effect sensors. Experimental measurements of magnetic flux density within the area of interest were used to formulate analytic expressions that relate magnet field strength to the position of the magnet. The displacement and orientation measurement and the material properties of the elastomer are …

Multi-Disciplinary Hands-On Desktop Learning Modules And Modern Pedagogies, Bernard J. Van Wie, David B. Thiessen, Marc Compere, Ximena Toro, Jennifer C. Adam, Et Al.

Marc Compere

Our team’s research focuses on fundamental problems in undergraduate education in terms of how to expand use of well researched, yet still “new”, teaching pedagogies of ‘sensing’ or ‘hands-on’, ‘active’ and ‘problem-based learning’ within engineering courses. It is now widely accepted that traditional lectures ARE NOT best for students – yet that is what the community almost universally does. To address this issue we are developing new Desktop Learning Modules (DLMs) that contain miniaturized processes with a uniquely expandable electronic system to contend with known sensor systems/removable cartridges, as well as, unknown expansions to the project. We have shown that …

Project Haiti 2012: Providing An Experiential Learning Experience Through The Design And Delivery Of A Water Purifier In Haiti, Yung Wong, Johnathon Camp, Shavin Pinto, Kyle Fennesy, Marc Compere, Yan Tang

Marc Compere

In this paper, we share our experiences and lessons learned from Project Haiti 2012, a project to design and install a water purification system serving 20,000 people per day in the largest tent city in Haiti. Project Haiti 2012 was the third and largest system we have built for Haitians and represents a huge success for all participants and stakeholders. This paper discusses the unique experiential learning opportunity involved in the design and delivery of the water purifier in a foreign developing country. Multiple positive educational, social, and economic outcomes were achieved including students applying knowledge gained from coursework towards …

High Tech High Touch: Lessons Learned From Project Haiti 2011, Yan Tang, Marc Compere, Yung Lun Wong, Jared Anthony Coleman, Matthew Charles Selkirk

Marc Compere

In this paper, we will share our experiences and lessons learned from a design project for providing clean water to a Haitian orphanage (Project Haiti 2011). Supported by funds from a renewable energy company and the university president’s office, five engineering students and two faculty members from Embry-Riddle Aeronautical University successfully designed and installed a solar powered water purification system for an orphanage located in Chambellan, Haiti. This paper discusses the unique educational experiences gained from unusual design constraints, such as ambiguity of existing facilities due to limited communication, logistics of international construction at a remote village location, and cross-cultural …

Industrial Solid-State Energy Harvesting: Mechanisms And Examples, Matthew Kocoloski, Carl Eger, Robin Mccarty, Kevin P. Hallinan, J. Kelly Kissock

J. Kissock

This paper explores the potential for solid-state energy harvesting in industrial applications. In contrast to traditional heat recovery, the output of solid-state devices is electricity, which can be readily used in virtually any plant. The progress in harvesting waste heat via thermoelectric and thermionic generators is described. With second law efficiencies now approaching 50% and 80% respectively, we show that these technologies are on the cusp of practical use. Finally, we present an example of energy harvesting using thermionic devices in an industrial application. The example considers energy harvesting from a furnace at a glass manufacturing facility where exhaust gases …

Performance Prediction Of Drying Process In Residential Clothes Dryer Using Multiphysics Modeling And Simulation, Molly Shircliff

Mahurin Honors College Capstone Experience/Thesis Projects

The clothes dryer is the second highest consumer of electricity among household appliances in the U.S. However, few improvements have been made to the overall design of dryers since the 1970s. For this reason, energy efficiency research in domestic clothes dryers is a promising topic. In order to effectively and accurately research and test efficiency and design of new prototypes of the dryer, a mathematical model of the air-vented, residential dryer was created in the Energy Systems Lab at Western Kentucky University, using the text-based environment of MATLAB. This model was developed and simulated using numerical solver techniques. This model …

Designing And Building An Automatic Chamfer Grinder, William Johnson

Mahurin Honors College Capstone Experience/Thesis Projects

Modern day manufacturing is a demanding environment with a constant need for process improvement. As automation becomes more advanced, there are fewer jobs that must be completed by a human. In the case of Stupp Bridge Company, a local manufacturer of steel bridge girders, their workforce is highly skilled, so replacing mundane tasks with automation allow the skilled workers to focus on the difficult jobs. One such task is grinding a chamfer onto every leading edge of each girder flange, eight edges in total, ranging from 20 to 200 feet long. The purpose of this project was to design an …

Dynamic Modeling Of Contact-Mode Triboelectric Generators By Lagrange’S Equations, Sean M. Gauntt, James Gibert

The Summer Undergraduate Research Fellowship (SURF) Symposium

Electret based energy scavenging devices utilize electrostatic induction to convert mechanical energy into electrical energy. Uses for these devices include harvesting ambient energy in the environment and acting as sensors for a range of applications. These types of devices have been used in MEMS applications for over a decade. However, recently there is an interest in Triboelectric generators/harvesters, i.e., electret based harvesters that relies on triboelectrification as well as electrostatic induction. The literature is filled with a variety of designs for the latter devices, constructed from materials ranging from paper and thin films; rendering the generators lightweight, flexible and inexpensive. …

Mechanical Reliability Of Implantable Polyimide-Based Magnetic Microactuators For Biofouling Removal, Christian G. Figueroa-Espada, Qi Yang, Hyowon Lee

The Summer Undergraduate Research Fellowship (SURF) Symposium

Hydrocephalus is a neurological disorder that typically requires a long-term implantation of a shunt system to manage its symptoms. These shunt systems are notorious for their extremely high failure rate. More than 40% of all implanted shunt systems fail within the first year of implantation. On average, 85% of all hydrocephalus patients with shunt systems undergo at least two shunt-revision surgeries within 10 years of implantation. A large portion of this high failure rate can be attributed to biofouling-related obstructions and infections. Previously, we developed flexible polyimide-based magnetic microactuators to remove obstructions formed on hydrocephalus shunts. To test the long-term …

Energy Information Augmented Community-Based Energy Reduction, Kevin P. Hallinan, Harvey Enns, Stephenie Ritchey, Phil Brodrick, Nathan Lammers, Nichole Hanus, Mark Rembert, Tony Rainsberger

Harvey Enns

More than one-half of all U.S. states have instituted energy efficiency mandates requiring utilities to reduce energy use. To achieve these goals, utilities have been permitted rate structures to help them incentivize energy reduction projects. This strategy is proving to be only modestly successful in stemming energy consumption growth. By the same token, community energy reduction programs have achieved moderate to very significant energy reduction. The research described here offers an important tool to strengthen the community energy reduction efforts—by providing such efforts energy information tailored to the energy use patterns of each building occupant. The information provided most importantly …

Design, Testing And Evaluation Of Robotic Mechanisms And Systems For Environmental Monitoring And Interaction, James K. Higgins

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Unmanned Aerial Vehicles (UAVs) have significantly lowered the cost of remote aerial data collection. The next generation of UAVs, however, will transform the way that scientists and practitioners interact with the environment. In this thesis, we address the challenges of flying low over water to collect water samples and temperature data. We also develop a system that allows UAVs to ignite prescribed fires. Specifically, this thesis contributes a new peristaltic pump designed for use on a UAV for collecting water samples from up to 3m depth and capable of pumping over 6m above the water. Next, temperature sensors and their …

Hybrid Magneto-Rheological Actuators For Human Friendly Robotic Manipulators, Masoud Moghani

Electronic Thesis and Dissertation Repository

In recent years, many developments in the field of the physical human robot interaction (pHRI) have been witnessed and significant attentions have been given to the subject of safety within the interactive environments. Ensuring the safety has led to the design of the robots that are physically unable to hurt humans. However, Such systems commonly suffer from the safety-performance trade-off. Magneto-Rheological (MR) fluids are a special class of fluids that exhibit variable yield stress with respect to an applied magnetic field. Devices developed with such fluids are known to provide the prerequisite requirements of intrinsic safe actuation while maintaining the …

A Haptic Surface Robot Interface For Large-Format Touchscreen Displays, Mark Price

Masters Theses

This thesis presents the design for a novel haptic interface for large-format touchscreens. Techniques such as electrovibration, ultrasonic vibration, and external braked devices have been developed by other researchers to deliver haptic feedback to touchscreen users. However, these methods do not address the need for spatial constraints that only restrict user motion in the direction of the constraint. This technology gap contributes to the lack of haptic technology available for touchscreen-based upper-limb rehabilitation, despite the prevalent use of haptics in other forms of robotic rehabilitation. The goal of this thesis is to display kinesthetic haptic constraints to the touchscreen user …

Microscale Investigation Of Thermo-Fluid Transport In The Transition Fil, Region Of An Evaporating Capillary Meniscus Using A Microgravity Environment, Kenneth D. Kihm, Jeffrey S. Allen, Kevin P. Hallinan, David M. Pratt

Kevin Hallinan

In order to enhance the fundamental understanding of thin film evaporation and thereby improve the critical design concept for two-phase heat transfer devices, microscale heat and mass transport is to be investigated for the transition film region using state-of-the-art optical diagnostic techniques. By utilizing a microgravity environment, the length scales of the transition film region can be extended sufficiently, from submicron to micron, to probe and measure the microscale transport fields which are affected by intermolecular forces. Extension of the thin film dimensions under microgravity will be achieved by using a conical evaporator made of a thin silicon substrate under …

Nanocharacterization Of Bio-Silica Using Atomic Force And Ultrasonic Force Microscopy, Vinaypreet S. Gill, Kevin P. Hallinan, N. S. Brar

Kevin Hallinan

Nanotechnology has become central to our research efforts to fabricate relatively smaller size devices, which are more versatile than their older and larger predecessors. Silica is a very important material in this regard. Recently, a new biomimetically inspired path to silica production has been demonstrated. This processing technique was inspired from biological organisms, such as marine diatoms, which produce silica at ambient conditions and almost neutral ph with beautiful control over location and structure. Recently, several researchers have demonstrated that positional control of silica formed could be achieved by application of an electric field to locate charged enzymes responsible for …

Leveraging Students’ Passion And Creativity: Ethos At The University Of Dayton, Margaret Pinnell, Malcolm Daniels, Kevin P. Hallinan, Gretchen Berkemeier

Kevin Hallinan

The Engineers in Technical Humanitarian Opportunities of Service-learning (ETHOS) program was developed in the spring of 2001 by an interdisciplinary group (electrical, chemical, civil and mechanical) of undergraduate engineering students at the University of Dayton (UD). ETHOS was founded on the belief that engineers are more apt and capable to appropriately serve our world if they have an understanding of technology’s global linkage with values, culture, society, politics, and the economy. Since 2001, the ETHOS program at UD has grown and changed. From conceptualization, to implementation, to maturation and national recognition, the program has addressed challenges of academic acceptance, programmatic …

Experimental Verification Of Source Temperature Modulation Via A Thermal Switch In Thermal Energy Harvesting, Robin Mccarty, D. Monaghan, Kevin P. Hallinan, Brian Sanders

Kevin Hallinan

This paper provides a description of research seeking to experimentally verify the effectiveness of a thermal switch used in series with TE devices for waste heat recovery for constant and variable source heat input and for variable source thermal capacitance (mass). Using an experimental set-up comprised serially of a fixed heat source, a variable thermal resistance air gap serving as a thermal switch, a thermoelectric device and a heat sink, the time-averaged power output to power input ratios improved up to 15% and 30% respectively for constant and variable heat input in certain design space conditions. The experimental results, as …

Industrial Solid-State Energy Harvesting: Mechanisms And Examples, Matthew Kocoloski, Carl Eger, Robin Mccarty, Kevin P. Hallinan, J. Kelly Kissock

Kevin Hallinan

This paper explores the potential for solid-state energy harvesting in industrial applications. In contrast to traditional heat recovery, the output of solid-state devices is electricity, which can be readily used in virtually any plant. The progress in harvesting waste heat via thermoelectric and thermionic generators is described. With second law efficiencies now approaching 50% and 80% respectively, we show that these technologies are on the cusp of practical use. Finally, we present an example of energy harvesting using thermionic devices in an industrial application. The example considers energy harvesting from a furnace at a glass manufacturing facility where exhaust gases …

Energy Information Augmented Community-Based Energy Reduction, Kevin P. Hallinan, Harvey Enns, Stephenie Ritchey, Phil Brodrick, Nathan Lammers, Nichole Hanus, Mark Rembert, Tony Rainsberger

Kevin Hallinan

More than one-half of all U.S. states have instituted energy efficiency mandates requiring utilities to reduce energy use. To achieve these goals, utilities have been permitted rate structures to help them incentivize energy reduction projects. This strategy is proving to be only modestly successful in stemming energy consumption growth. By the same token, community energy reduction programs have achieved moderate to very significant energy reduction. The research described here offers an important tool to strengthen the community energy reduction efforts—by providing such efforts energy information tailored to the energy use patterns of each building occupant. The information provided most importantly …

Electro-Hydrodynamic Pumped Hydraulic Actuation With Application To Active Vibration Control, Ahmad Reza Kashani, Sung Kang, Kevin P. Hallinan

Kevin Hallinan

A new type of actuation device has been conceptualized that meets the needs of both large displacement, force and bandwidth within a package more compact than currently available magnetostrictive and stack-type piezoelectric actuators of similar rating. This concept relies on micro-scale electrohydrodynamic (EHD) pumping of a dielectric liquid within small channels. Configured as an actuator, the EHD pump(s) would be used to move fluid between two reservoirs—each having a compliant membrane that interfaces to the world to provide the means to achieve vibration cancellation or micro actuation. Ordinarily limited to generating flow in macroscale applications, the EHD pump, when operating …

A Study Of The Fundamental Operations Of A Capillary Driven Heat Transfer Device In Both Normal And Low Gravity Part 1-Liquid Slug Formation In Low Gravity, Jeffrey S. Allen, Kevin P. Hallinan, Jack Lekan

Kevin Hallinan

Research has been conducted to observe the operation of a capillary pumped loop (CPL) in both normal and low gravity environments in order to ascertain the causes of device failure. The failures of capillary pumped heat transport devices in low gravity; specifically; evaporator dryout, are not understood and the available data for analyzing the failures is incomplete. To observe failure in these devices an idealized experimental CPL was configured for testing in both a normal-gravity and a low-gravity environment. The experimental test loop was constructed completely of Pyrex tubing to allow for visualization of system operations. Heat was added to …

Clean Energy Infrastructure Educational Initiative, Kevin P. Hallinan, James A. Menart, Robert Gilbert

Kevin Hallinan

The Clean Energy Infrastructure Educational Initiative represents a collaborative effort by the University of Dayton, Wright State University and Sinclair Community College. This effort above all aimed to establish energy related programs at each of the universities while also providing outreach to the local, state-wide, and national communities. At the University of Dayton, the grant has aimed at: solidfying a newly created Master's program in Renewable and Clean Energy; helping to establish and staff a regional sustainability organization for SW Ohio. As well, as the prime grantee, the University of Dayton was responsible for ensuring curricular sharing between WSU and …

Automated Bearing Press, David Baker, David Brock, Engelbert Diec

Mechanical Engineering

Our group was presented with a challenge to design an automated machine to replace Micro-Vu’s current manual pressing operation. We moved, planned, and scheduled our tasks for the three quarters we will be working on this project by using a Gantt chart. In designing the machine, we generated concepts and used analysis and prototyping to select the most promising ones. Our final design uses a pneumatic press to press the parts, and it includes magazines to hold the parts before pressing, pneumatic actuators to move the parts to and from the pressing location, and a lever to separate the defective …

Cp Ev Dynamics, Steven Montevideo, Ashlie Reott, L. Carter Price

Mechanical Engineering

No abstract provided.