Mechanical Engineering Commons^™

A Study On Stainless Steel 316l Annealed Ultrasonic Consolidation And Linear Welding Density Estimation, Raelvim Gonzalez

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Ultrasonic Consolidation of stainless steel structures is being investigated for potential applications. This study investigates the suitability of Stainless Steel 316L annealed (SS316L annealed) as a building material for Ultrasonic Consolidation (UC), including research on Linear Welding Density (LWD) estimation on micrographs of samples. Experiment results are presented that include the effect of UC process parameters on SS316L annealed UC, optimum levels of these parameters, and bond quality of ultrasonically consolidated SS316L annealed structures in terms of LWD. In support to these efforts, a Measurement System Analysis for LWD assessment has been performed, and a new instrument for LWD measurement …

Effects Of Temperature And Humidity On Glass-Reinforced Nylon Rotating Bands, Marc D. Raby

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Certain 30mm munitions used in various military applications are configured with a glass-reinforced nylon band that acts as a firing ring or rotating band. The purpose of this research is to investigate whether storage environments compromise the strength and integrity of the glass-reinforced nylon rotating bands by researching the environmental factors that will degrade nylon and by performing tests to investigate if these factors will embrittle nylon composites. Moisture and temperature are found to be the environmental factors that will have an effect on the rotating bands in their respective storage environments. Absorbed moisture is found to increase the impact …

Experiment And Simulation On The Dynamics Of A Slug Of Liquid Oxygen Displaced By A Pulsed Magnetic Field, Jeffrey C. Boulware

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A magnetic fluid system could potentially replace mechanically moving parts in a satellite as a means of increasing system reliability and mission lifetime, but rather than a standard ferrofluid with magnetic particles, liquid oxygen (LOX) may be a more adequate working fluid. As a pure paramagnetic cryogen, LOX is already heavily used in space, but still requires basic research before being integrated into system development. The objectives of the research conducted were to verify LOX as a magnetic working fluid through experiment and establish a theoretical model to describe its behavior. This dissertation presents the theoretical, experimental, and numerical results …

The Cryogenic Bonding Evaluation At The Metallic-Composite Interface Of A Composite Overwrapped Pressure Vessel With Additional Impact Investigation, Eric A. Clark

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A bonding evaluation that investigated the cryogenic tensile strength of several different adhesives / resins was performed. The test materials consisted of 6061 aluminum test pieces adhered to a wet-wound graphite laminate in order to simulate the bond created at the liner-composite interface of an aluminum lined composite overwrapped pressure vessel. It was found that for cryogenic applications, a flexible, low modulus resin system must be used. Additionally, the samples prepared with a thin layer of cured resin – or prebond – performed significantly better than those without. It was found that it is critical that the prebond surface must …

Parallelization Of Performance Limiting Routines In The Computational Fluid Dynamics General Notation System Library, Kyle Horne

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The Computational Fluid Dynamics General Notation System provides a unified way in which computational fluid dynamics data can be stored, but does not support the parallel I/O capabilities now available from version five of the Hierarchical Data Format library which serves as a back end for he standard. To resolve this deficiency, a new parallel extension library has been written and benchmarked for this work which can write files compliant with the standard using parallel file access modes. When using this new library, the write performance shows an increase of four-fold in some cases when compared to the same hardware …

Interim Access To The International Space Station, Tyson Karl Smith

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This thesis evaluates mission scenarios using the existing Evolved Expendable Launch Vehicles for delivering the Crew Exploration Vehicle to the International Space Station. The Space Shuttle is scheduled to retire in the year 2011 and the Ares I is being developed to replace it. With its current schedule, the earliest that the Ares I will become fully operational is 2016. The configurations in this thesis are presented to narrow the gap in which the USA does not have direct access to the International Space Station. They also present "buy down" options for the USA human space operations, if the current …

Stability Of Basin-Scale Internal Waves Within The South Arm Of The Great Salt Lake, Joshua David Soelberg

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The fluid circulation patterns, temperature distributions, and density gradients of the South Arm of the Great Salt Lake were modeled using the Estuary, Lake, and Coastal Ocean Model (ELCOM) from the Centre for Water Research at the University of Western Australia. The effort is part of a research study in conjunction with the United States Geological Survey (USGS) and the Utah Water Research Lab located at Utah State University. The model was simulated for several different cases of salinity gradients over different time periods, using temperature and wind data from 2006. The model is then used to identify factors which …

Demonstration Of A Completely Described Swirling Jet Experiment Used For Numerical Validation, Brandon M. Wilson

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This thesis demonstrates the standard for the design of an experimental model to be used for numerical validation purposes. It is proposed that numerical models may be assessed more accurately and directly by validation with a completely described experimental model, consisting of accurate descriptions of the operating conditions, fluid properties, and experimental uncertainties. This idea is demonstrated using an experimental model of a swirling jet at three Reynolds numbers (Re = 550, 2560, and 3650), with vortex breakdown existing in the higher two Reynolds number cases. Measurements of the swirling jet were obtained at two locations upstream of the jet …

Modeling, Designing, Fabricating, And Testing Of Channel Panel Flat Plate Heat Pipes, James R. Harris

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Flat plate heat pipes are very efficient passive two-phase heat transport devices. Their high efficiency and low mass are desirable in the aerospace and electronics industries. The highly competitive nature of the thermal management industry results in little awareness of the capabilities of at plate heat pipes, which has resulted in only a few applications of the technology. In the year 2000 a research and development project sponsored by Space Dynamics Laboratory was launched to investigate building carbon-based at heat pipes. The flat configuration is desireable to incorporate many components onto one thermal management system. Development led to the adoption …

Angles-Only Navigation For Autonomous Orbital Rendezvous, David Charles Woffinden

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The proposed thesis of this dissertation has both a practical element and theoretical component which aim to answer key questions related to the use of angles-only navigation for autonomous orbital rendezvous. The first and fundamental principle to this work argues that an angles-only navigation filter can determine the relative position and orientation (pose) between two spacecraft to perform the necessary maneuvers and close proximity operations for autonomous orbital rendezvous. Second, the implementation of angles-only navigation for on-orbit applications is looked upon with skeptical eyes because of its perceived limitation of determining the relative range between two vehicles. This assumed, yet …

Particle Characterization And Concentration Using Aerodynamic Vectoring, Zac Humes

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

An experimental demonstration of a new, non-contact particle characterization technique called Aerodynamic Vectoring Particle Sorting (AVPS) is presented. AVPS uses secondary blowing and suction control flows-flows that are a fraction of the jet flow rate-to sharply change the direction of a planar, particle-laden jet. As the jet is vectored, particles present in the flow experience a resultant drag force, dependent upon their size, that balances inertia. Since this balance determines the particle's trajectory, vectoring the flow leads to a separation of particles downstream. This simple, low-pressure-drop sorting technique classifies particles with less risk of damage or contamination than currently available …

Hydrogen Production Using Geothermal Energy, Theodore Wayne Hand

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

With an ever-increasing need to find alternative fuels to curb the use of oil in the world, many sources have been identified as alternative fuels. One of these sources is hydrogen. Hydrogen can be produced through an electro-chemical process. The objective of this report is to model an electrochemical process and determine gains and or losses in efficiency of the process by increasing or decreasing the temperature of the feed water. In order to make the process environmentally conscience, electricity from a geothermal plant will be used to power the electrolyzer. Using the renewable energy makes the process of producing …

Variational Asymptotic Micromechanics Modeling Of Composite Materials, Tian Tang

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The issue of accurately determining the effective properties of composite materials has received the attention of numerous researchers in the last few decades and continues to be in the forefront of material research. Micromechanics models have been proven to be very useful tools for design and analysis of composite materials. In the present work, a versatile micromechanics modeling framework, namely, the Variational Asymptotic Method for Unit Cell Homogenization (VAMUCH), has been invented and various micromechancis models have been constructed in light of this novel framework. Considering the periodicity as a small parameter, we can …

A Three-Dimensional, Time-Dependent Circulation Model Of Utah Lake, Eric V. Callister

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Spatial and temporal variations of Utah Lake’s flow field were modeled using the Estuary Lake and Computer Model from the Centre for Water Research (CWR-ELCOM) at the University of Western Australia as part of an effort to increase understanding of the lake’s natural processes in order to restore the lake to its pristine, clear-water state and preserve the habitat of the June sucker, an endangered species. The model was validated using temperature measurements taken by sensors in 2007. The water temperature was a strong function of air temperature and incident short wave radiation, and was influenced to a lesser degree …

Fabrication Of Long-Fiber-Reinforced Metal Matrix Composites Using Ultrasonic Consolidation, Yanzhe Yang

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This research is a systematic study exploring a new fabrication methodology for long-fiber-reinforced metal matrix composites (MMCs) using a novel additive manufacturing technology. The research is devoted to the manufacture of long-fiber-reinforced MMC structures using the Ultrasonic Consolidation (UC) process. The main objectives of this research are to investigate the bond formation mechanisms and fiber embedment mechanisms during UC, and further to study the effects of processing parameters on bond formation and fiber embedment, and the resultant macroscopic mechanical properties of UC-made MMC structures.

From a fundamental research point of view, bond formation mechanisms and fiber embedment mechanisms have been …

Development Of A Mathematical Model For 3d Reconstruction Of Target Objects By Photogrammetry, Keith F. Blonquist

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This thesis outlines the development of a mathematical model which can be used to perform 3D reconstruction of a target object from surveillance images. 3D reconstruction is a common procedure in photogrammetry, but performing 3D reconstruction from surveillance images can be more difficult than typical photogrammetry applications.

Surveillance images are generally captured in an unsystematic manner because there is no control over the target that is being photographed. Surveillance images can have a wide variety of fields of view, are often captured with uncalibrated cameras, and typically the targets are objects for which there is no other a priori information. …

Axisymmetric Coanda-Assisted Vectoring, Dustin S. Allen

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

An examination of parameters affecting the control of a jet vectoring technique used in the Coanda-assisted Spray Manipulation (CSM) is presented. The CSM makes use of an enhanced Coanda effect on axisymmetric geometries through the interaction of a high volume primary jet flowing through the center of a collar and a secondary high-momentum jet parallel to the first and adjacent to the convex collar. The control jet attaches to the convex wall and vectors according to known Coanda effect principles, entraining and vectoring the primary jet, resulting in controllable r-θ directional spraying. Several control slots (both annular and unique sizes) …

Pipe5 Finite Element Analysis For Buried Structures, David Aldous

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

PIPE5 is a finite element analysis (FEA) program designed to analyze buried pipes and culverts whose development was spearheaded by A. P. Moser. PIPE5 started as a modification of the program SSTIPN in 1981 so that the program could run in batch mode on a mainframe and was written in Fortran IV language. Various students made modifications to the original code making it compatible with personal computers and adding additional features. For more history on early PIPE5 developments see Moser [1]. In 2003 Mr. Merrill began a project of updating PIPE5. Mariner did extensive work on making the code compatible …

Time-Resolved Piv And Pressure Measurements Of Oscillating And Pulsating Flow In A Diffuser, Cameron V. King

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Separating oscillating and pulsating flows in an internal adverse pressure gradient geometry are studied experimentally. Simultaneous velocity-pressure measurements demonstrate that the minor losses associated with oscillating flow in an adverse pressure gradient geometry can be smaller or larger than for steady flow. Separation is found to begin high in the diffuser and propagate downward. Flows are able to remain attached further into the diffuser with larger Reynolds numbers, larger stroke lengths, and smaller diffuser angles. The extent of separation grows with L₀/h. The minor losses grow with increasing displacement amplitude in the range 10 < L₀/h …