Open Access. Powered by Scholars. Published by Universities.®

Mechanical Engineering Commons

Open Access. Powered by Scholars. Published by Universities.®

Articles 1 - 7 of 7

Full-Text Articles in Mechanical Engineering

Impurity Effects In All-Vanadium Redox Flow Batteries, Andrew William Burch Dec 2015

Impurity Effects In All-Vanadium Redox Flow Batteries, Andrew William Burch

Masters Theses

In this dissertation, the effects of VOSO4 [vanadyl sulfate] source and impurities on the beginning-of-life (BOL) performance of an all-vanadium redox flow battery (VRFB) are explored. Battery performance was monitored at 50% state of charge (SOC) using electrolyte with VOSO4 purities of 99%, 99.9% and 99.99% by weight. At cell potentials of 1.23V, the least pure solution yielded the lowest current density of 280 mA/cm2 [square centimeter] and the most pure solution yielded the highest, 560 mA/cm2. The voltage efficiencies and charge-discharge capacities were shown to follow the same trends. Scanning electron microscopy (SEM) images …


Extending The Lean Limit Of Methane-Air Mixtures By Oxygen, Nitrogen And Carbon Dioxide Injection In The Gap Of The Spark Plug’S Electrodes, Artem Alexandrov Temerev Dec 2015

Extending The Lean Limit Of Methane-Air Mixtures By Oxygen, Nitrogen And Carbon Dioxide Injection In The Gap Of The Spark Plug’S Electrodes, Artem Alexandrov Temerev

Masters Theses

An experimental investigation is carried out to investigate the feasibility of extending the lean limit for methane–air mixtures by injecting oxygen and other gases such as nitrogen and carbon dioxide in the area between spark plug electrodes. Additionally, the effect of oxygen injection on exhaust gas recirculation (EGR) is investigated. The pressure in the chamber and the equivalence ratio of the mixture are varied from 0.35 MPa to 1.03 MPa and 0.46 to 1.0, respectively. Delco 12620540 spark plug is used as the ignition source and the gas injection into spark plug gap is accomplished through a 0.159-cm OD stainless …


Evaluation Of Fuel Flow Measurement Uncertainty In A Turbine Engine Test Cell, Paul Andrew Wright Dec 2015

Evaluation Of Fuel Flow Measurement Uncertainty In A Turbine Engine Test Cell, Paul Andrew Wright

Masters Theses

The evaluation of measurement uncertainty is an essential part of measurement and data analysis. Measurement uncertainty is itself a measure of the “goodness” of the measured data and helps the analyst to make decisions based on the data. In the turbine engine testing world, accurate measurement of fuel flow is critical. Specific fuel consumption is a combination of thrust and fuel flow and is used to calculate the allowable payload and range of an aircraft as well as the cruising speed. Naturally, test customers (engine manufacturers, aircraft designers, and operators) are very sensitive to the accuracy of fuel flow measurement. …


Optimization Of Titanium Liquid/Gas Diffusion Layers In Proton Exchange Membrane Electrolyzer Cells, Stuart Mccoy Steen Dec 2015

Optimization Of Titanium Liquid/Gas Diffusion Layers In Proton Exchange Membrane Electrolyzer Cells, Stuart Mccoy Steen

Masters Theses

Polymer electrolyte membrane electrolyzer cells (PEMECs), which are reverse PEM fuel cells (PEMFCs), are effective energy storage medium by producing hydrogen/oxygen from water using electricity from renewable energy sources. This is due in part because of its efficiency, high energy density, compact design, and large capacity. In a PEMEC, a liquid/gas diffusion layer (LGDL) is located between the catalyst layer and the current distributing flow field. The LGDL is expected to transport electrons, heat, and reactants/products to and from the catalyst layer with minimum voltage, current, thermal, interfacial, and fluidic losses. Carbon materials (carbon paper or carbon cloth), typically used …


Phase Dynamics Of Locset Control Methodology, Brendan Neschke May 2015

Phase Dynamics Of Locset Control Methodology, Brendan Neschke

Masters Theses

Single-mode fiber amplifiers produce diffraction-limited beams very efficiently. Maximum beam intensity requires that an array of these amplifiers have their beams coherently combined at the target. Optical path differences and noise adversely affect beam quality. An existing closed loop phase control methodology, called the locking of optical coherence by single-detector electronic-frequency tagging (LOCSET), corrects phase errors in real time by electronically detecting path length differences and sending signals to lithium niobate phase adjusters. Broadening the line-width using “jitter” of the input signal can increase the output power of an individual amplifier by suppressing nonlinearity. The system dynamics of LOCSET are …


Cfd Analysis Of Viscosity Effects On Turbine Flow Meter Performance And Calibration, Carl Tegtmeier May 2015

Cfd Analysis Of Viscosity Effects On Turbine Flow Meter Performance And Calibration, Carl Tegtmeier

Masters Theses

In this research turbine flow meters were studied, using computational fluid dynamics (CFD) modeling to the study effects of viscosity on the flow meters, across a wide range of operation, to improve our understanding and their performance. A three-dimensional computational model was created for a typical flow meter geometry. The work began with a steady state model to provide an acceptable initial condition for further simulations. These results were input into a transient model that has a rotating zone around the rotor to provide insight into the interaction between static and rotational structures. In order to automatically adjust the rotor …


Impact Of Solidification On Tensile Strength Of Cocr 2lc In Selective Laser Melting, Stefan Robert Popp May 2015

Impact Of Solidification On Tensile Strength Of Cocr 2lc In Selective Laser Melting, Stefan Robert Popp

Masters Theses

Selective laser melting (SLM) is an additive manufacturing technique with which parts of nearly arbitrary shape and complexity can be produced. The parts are generated layer for layer directly out of a 3D CAD model completely without forming tools.

In this work, the selective laser technique is applied to a CoCrMo alloy. Due to its high corrosion resistance, wear-resistance, and heat resistance, this alloy is mainly used for medical or high temperature applications.

A systematic approach is used to investigate the influence of the process parameters laser power and exposure time (pulsed laser) on density, melt pool dimensions, melt pool …