Mechanical Engineering Commons^™

Numerical Analysis Of A Multi-Stage Elastohydrodynamic Seal For Aircraft Engines, Md Wasif Hasan

Electronic Theses and Dissertations

At present, both governmental and private aviation enterprises are trying to develop aircraft that are swifter, more lightweight, and more cost-effective in order to maintain competitiveness on both the domestic and global stage. Continuous innovation and sustainability efforts are necessary to achieve advancements in aviation systems, such as fans, compressors, combustors, and turbines, as well as sub-systems, like engine seals. Advanced engine seals exhibit considerable potential in enhancing the engine's pressure ratio and cycle temperatures, leading to reduced engine weight, increased thrust, and improved fuel economy. In this study, a novel multistage seal idea has been proposed for the supercritical …

Towards Cfd Investigations Into Particulate Air Pollution Of A Desert Urban Environment, Prosun Roy

UNLV Theses, Dissertations, Professional Papers, and Capstones

This dissertation has explored computational fluid dynamics (CFD) techniques for studying particulate air quality in the Las Vegas urban area. The dissertation is based on three research tasks: • High time-resolution fenceline air quality sensing and dispersion modeling for environmental justice-centered source attribution. (Chapter 2) • Pollen dispersion and deposition in real-world urban settings: A computational fluid dynamic study. (Chapter 3) • Effects of urban canopy parameterizations on modeling pollen dispersion and exposure. (Chapter 4) In Chapter 2, we investigate the facilitation of low-cost air quality sensors (LCAQS) and CFD technique on exposure assessment of environmental justice (EJ) communities and …

A Computational Fluid Dynamic Analysis Of Oxyacetylene Combustion Flow For Use In Material Response Boundary Conditions, Craig Meade

Theses and Dissertations--Mechanical Engineering

Oxyacetylene torches are used in the aerospace industry and research to test thermal protection system materials (TPS) due to their high flame temperatures and high heat flux capabilities. The purpose of this work is to determine a combustion model to accurately simulate the high temperature flow of an oxyacetylene torch. The flow conditions around a sample material can then be used as boundary conditions when modeling TPS material response. Two separate combustion models with equilibrium chemistry were investigated using ANSYS Fluent™; the Eddy-Dissipation Model, and the Partially Premixed model.The results of this study are compared to existing experiments for validation.

Fuel Injector Design Of A Hypersonic Jet Engine Using Computational Fluid Dynamics, Melissa Rose Mercado

UNLV Theses, Dissertations, Professional Papers, and Capstones

The development of hypersonic airbreathing engines, such as a supersonic combustion ramjet, or scramjet, are implemented for flight Mach numbers over 5 where combustion must occur in supersonic conditions. The advancement of scramjet propulsion has led to favored usage over rocket propulsion systems for in atmosphere applications due to their lighter weight, higher specific impulse, and greater maneuverability [1]. The combustor section of a scramjet engine houses the fuel injectors. Fuel is injected into the supersonic flow with the main objective of achieving rapid and thorough fuel-air mixing because the residence time in the combustion chamber has a timescale of …

A Study Of Asymmetric Supersonic Wind Tunnel Nozzle Design, Brittany A. Davis

Mechanical & Aerospace Engineering Theses & Dissertations

Achieving higher Mach numbers for private and commercial flight is a growing interest in the aerospace community. To qualify vehicles prior to flight, tests must be run in wind tunnels. Asymmetric wind tunnel nozzles are of continuing interest to the aerospace community due to their ability to change throat geometry, allowing for a range of Mach numbers to be achieved that encompasses all of the supersonic regime. The sliding block wind tunnel at Old Dominion University (ODU) is designed for a range of Mach numbers from about 1.8 to 3.5 but is limited to an upper limit of 2.8 by …

Investigating Ground Interactions Of A Rotocraft Landing Vehicle On Titan, Adam Rozman

Honors Undergraduate Theses

The exploration of celestial bodies has recently advanced from rovers to rotorcraft. This includes the recent flights of Mars Ingenuity and the upcoming Dragonfly mission to explore the terrain of Saturn’s moon Titan as part of NASA’s New Frontiers Program. Flight-based landers can travel quickly to sites kilometers apart and land in complex terrain. Although cruise conditions for these rotorcrafts are well understood, studies are necessary to understand take-off and landing. In ground effect conditions, a rotor wake impinges and reflects off the ground, creating changes in aerodynamics such as increased lift. Additionally, operating over loose surfaces, the rotors can …

Cfd And Heat Transfer Analysis Of Rocket Cooling Techniques On An Aerospike Nozzle, Geoffrey Sullivan

Electronic Theses and Dissertations

In recent years the development of rocket engines has been mainly focused on improving the engine cycle and creating new fuels. Rocket nozzle design has not been changed since the late 1960s. Recent needs for reliable and reusable rockets, as well as advancements in additive manufacturing, have brought new interest into the aerospike nozzle concept. This nozzle is a type of altitude adjusting nozzle that is up to 90% more efficient than bell nozzles at low altitudes and spends up to 30% less fuel. Since the nozzle body is submerged in the hot exhaust gasses it is difficult to keep …

A Non-Reacting Passive Scalar Comparison Of Starccm And Openfoam In A Supersonic Cavity Flame Holder, Thomas Nuese

Electronic Theses and Dissertations

The scramjet engine equipped with a modern-day airliner would allow for very quick travel across the United States. The major problem is that designing such an engine and testing it to make sure it is safe would cost millions if not billions of dollars. Computational fluid dynamics allows for complex designs to be tested but can still take many days, weeks, or even months to complete. With the use of computational fluid dynamics (CFD), the scramjet engine can be analyzed to determine a quicker way to test and develop a reliable configuration in addition to analyzing the effects of different …

Modeling And Simulation Of A Supercritical Co2-Liquid Sodium Compact Heat Exchanger For Sodium Fast Reactors, Hailei Wang, Sean M. Kissick

Mechanical and Aerospace Engineering Faculty Publications

The study focuses on modeling and simulations of sodium-sCO2 intermediary compact heat exchangers for sodium-cooled fast reactors (SFR). A simplified 1-D analytical model was developed in companion with a 3-D CFD model. Using classic heat transfer correlations for Nusselt number, some simulation results using the 1-D model have achieved reasonable match with the CFD simulation results for longer channels (i.e., 40 cm and 80 cm). However, for short channel (10 cm) when axial conduction within the sodium fluid is significant, the 1-D model significantly over-predicted the heat transfer effectiveness. By incorporating the temperature-jump model, the 1-D model can extend its …

Magnetic Control Of Transport Of Particles And Droplets In Low Reynolds Number Shear Flows, Jie Zhang

Doctoral Dissertations

“Magnetic particles and droplets have been used in a wide range applications including biomedicine, biological analysis and chemical reaction. The manipulation of magnetic microparticles or microdroplets in microscale fluid environments is one of the most critical processes in the systems and platforms based on microfluidic technology. The conventional methods are based on magnetic forces to manipulate magnetic particles or droplets in a viscous fluid.

In contrast to conventional magnetic separation method, several recent experimental and theoretical studies have demonstrated a different way to manipulate magnetic non-spherical particles by using a uniform magnetic field in the microchannel. However, the fundamental mechanism …

Development Of Universal Solver For High Enthalpy Flows Through Ablative Materials, Umran Duzel

Theses and Dissertations--Mechanical Engineering

Atmospheric entry occurs at very high speeds which produces high temperature around the vehicle. Entry vehicles are thus equipped with Thermal Protection Systems which are usually made of ablative materials. This dissertation presents a new solver that models the atmospheric entry environment and the thermal protection systems. In this approach, both the external flow and the porous heat shield are solved using the same computational domain. The new solver uses the Volume Averaged Navier-Stokes Equations adapted for hypersonic non-equilibrium flow, and is thus valid for both domains. The code is verified using analytical problems, set of benchmarks and also a …

Computational Study Of Flow Interactions Over A Close Coupled Canard-Wing On Fighter, Setyawan Bekti Wibowo, Sutrisno Sutrisno, Tri Agung Rohmat

International Journal of Aviation, Aeronautics, and Aerospace

There have been many attempts to improve the flying performance of a fighter. By modifying the flow that occurs along the fuselage is expected to improve the performance of the aircraft. One of the indicators of combat aircraft performance is the ability to perform maneuver movement. Adding a canard as forewing on the fighter wing configuration is considered capable of raising the ability in maneuver movement. The use of canard-delta pairs will affect the performance and aerodynamic characteristics of the plane. Wings and canards with delta configuration will make the rolled-up vortex as a lifting force producer on the aircraft. …

Cfd Modeling Of Smoke Movement In An Atrium, Robin Wu

UNLV Theses, Dissertations, Professional Papers, and Capstones

The purpose of this paper is to better understand the behavior of smoke movement in an atrium. Thus gives first responders and civilians in and out of building a better understanding

With the advancements of modern technology, computers and softwares make simulation models possible such as fire models to simulate fire and smoke movements. In this paper, a computational fluid dynamic (CFD) software Fire Dynamic Simulator (FDS) is used to conduct a series of atrium tests to investigate the effectiveness of smoke exhaust systems. FDS solves the Navier-Stokes equations appropriate for low speed flows (Ma < 0.3) with an emphasis on smoke, heat transport and CO2 concentrations from fires. The default turbulence model used in FDS simulation is the Large Eddy Simulation (LES), which is the solution of Navier-Stokes equations at low speed.

The compartment tested was 9 …

Effect Of Aerogel On The Thermal Performance Of Corrugated Composite Sandwich Structures, Jacob Dillon Chess

Master's Theses

Current insulation solutions across multiple industries, especially the commercial sector, can be bulky and ineffective when considering their volume. Aerogels are excellent insulators, exhibiting low thermal conductivities and low densities with a porosity of around 95%. Such characteristics make aerogels effective in decreasing conductive heat transfer within a solid. These requirements are crucial for aerospace and spaceflight applications, where sensitive components exist among extreme temperature environments. When implemented into insulation applications, aerogel can perform better than existing technology while using less material, which limits the amount of volume allocated for insulation. The application of these materials into composites can result …

Liquid Jet Penetration And Breakup In A Free Supersonic Gas Jet, Hansen Jones

LSU Master's Theses

In the testing of today’s rocket engines, both on large scale vertical test stands and smaller subscale horizontal component testing stands, it is extremely important to be able to accurately quantify and mitigate the thermal and acoustic loads the engines will generate on test stand infrastructure. Due to the large number of parameters that must be considered for many cases, development of a multi-phase computational code is under way to properly analyze and design water spray cooling systems used at NASA’s Stennis Space Center (SSC) and across other NASA centers. As such, a small-scale experiment has been conducted at Louisiana …

Multiphase Flow Modeling For Design And Optimization Of A Novel Down-Flow Bubble Column, Mutharasu Lalitha Chockalingam

LSU Doctoral Dissertations

The application of the Euler-Euler framework based Computational Fluid Dynamics (CFD) models for simulating the two-phase gas-liquid bubbly flow in down-flow bubble columns is discussed in detail. Emphasis is given towards the modelling and design optimization of a novel down-flow bubble column. The design features of this novel down-flow bubble column and its advantages over a conventional Plunging Jet down-flow bubble column are discussed briefly. Then, some of the present challenges in simulating a conventional Plunging Jet down-flow bubble column in the Euler-Euler framework is highlighted, and a sigmoid function based drag modification function is implemented to overcome those challenges. …

Numerical Characterization Of The Flow Field And Heat Transfer Inside The Receiver Of A Parabolic Trough Solar Collector Carrying Supercritical Co2, Samad Gharehdaghimollahajloo

UNLV Theses, Dissertations, Professional Papers, and Capstones

The aim of this research is to provide a detailed numerical analysis of flow field and heat transfer inside the heat collecting element of a parabolic trough collector. The parabolic trough collector is used as the boiler in a direct Super Critical Carbon Dioxide (S-CO2) Brayton cycle.

A single collector is modeled and analyzed with different inlet conditions. The working fluid is supercritical since its pressure is increased to above critical pressure in the compressor while its temperature reaches 300 °C after passing through the recuperators and before entering the solar field. For the first time, this research considers both …

Evaluation Of Flux Correction On Three-Dimensional Strand Grids With An Overset Cartesian Grid, Dalon G. Work

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Simulations of fluid flows over complex geometries are typically solved using a solution technique known as the overset meshing method. The geometry is meshed using grid types appropriate to the local geometry in a patchwork fashion, rather than meshing the entire geometry with one type of mesh. The strand-Cartesian approach is a simplification of this process. While high-order accurate solvers on Cartesian grids are simple to implement, strand grids are usually restricted to second-order accuracy, resulting in poor quality solutions. Flux correction is a high-order accurate solution method, specifically designed for use on strand grids. The flux correction method on …

Development Of An Analysis And Design Optimization Framework For Marine Propellers, Ashish C. Tamhane

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, a framework for the analysis and design optimization of ship propellers is developed. This framework can be utilized as an efficient synthesis tool in order to determine the main geometric characteristics of the propeller but also to provide the designer with the capability to optimize the shape of the blade sections based on their specific criteria.

A hybrid lifting-line method with lifting-surface corrections to account for the three-dimensional flow effects has been developed. The prediction of the correction factors is achieved using Artificial Neural Networks and Support Vector Regression. This approach results in increased approximation accuracy compared …

Computational Fluid Dynamic Analysis Of Microbubble Drag Reduction Systems At High Reynolds Number, John D. Goolcharan

FIU Electronic Theses and Dissertations

Microbubble drag reduction (MBDR) is an effective method to improve the efficiency of fluid systems. MBDR is a field that has been extensively studied in the past, and experimental values of up to 80% to 90% drag reduction have been obtained. The effectiveness and simplicity of MBDR makes it a viable method for real world applications, particularly in naval applications where it can reduce the drag between the surface of ships and the surrounding water. A two dimensional single phase model was created in ANSYS Fluent to effectively model the behavior of bubble laden flow over a flat plate. This …

Numerical And Experimental Study Of Liquid Breakup Process In Solid Rocket Motor Nozzle, Yi-Hsin Yen

Theses and Dissertations

Rocket propulsion is an important travel method for space exploration and national defense, rockets needs to be able to withstand wide range of operation environment and also stable and precise enough to carry sophisticated payload into orbit, those engineering requirement makes rocket becomes one of the state of the art industry. The rocket family have been classified into two major group of liquid and solid rocket based on the fuel phase of liquid or solid state. The solid rocket has the advantages of simple working mechanism, less maintenance and preparing procedure and higher storage safety, those characters of solid rocket …

Development Of A Three-Dimensional High-Order Strand-Grids Approach, Oisin Tong

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The strand-Cartesian grid approach is a unique method of generating and computing fluid dynamic simulations. The strand-Cartesian approach provides highly desirable qualities of fully-automatic grid generation and high accuracy. This work focuses on development of a high-accuracy methodology (high-order scheme) on strand grids for two and three dimensions.

In this work, the high-order scheme is extended to high-Reynolds number computations in both two and three dimensions with the Spalart-Allmaras turbulence model and the Menter SST turbulence model. In addition, a simple limiter is explored to allow the high-order scheme to accurately predict discontinuous flows.

Extensive verification and validation is conducted …

Analysis Of Road Vehicle Aerodynamics With Computational Fluid Dynamics, Christian Armando Mata

Open Access Theses & Dissertations

A road vehicles aerodynamics can be one of the most influential aspects of its performance. With the increased importance on fuel efficiency in recent years, new road vehicles are being developed smaller in size, with smaller displacement engines, as well as with improved aerodynamics. The aerodynamics of a vehicle can have a significant effect on its fuel efficiency, as well as other important aspects of the vehicles performance such as the top speed, acceleration, and handling. A study focusing on analyzing aerodynamic effects due to vehicle geometries such as wheels covered by the vehicles body in comparison to open wheels …

Design Of A High Intensity Turbulent Combustion System, Mohammad Arif Hossain

Open Access Theses & Dissertations

In order to design next generation gas turbine combustor and rocket engines, a systematic study of flame structure at high intensity turbulent flow is necessary. The fundamental study of turbulent premixed combustion has been a major research concern for decades. The work is focused on the design and development of a high intensity turbulent combustion system which can be operated at compressible (0.3 < M < 0.5), preheated (T0=500K) and premixed conditions in order to investigate the 'Thickened Flame' regime. An air-methane mixture has been used as the fuel for this study. An optically accessible backward-facing step stabilized combustor has been designed for a maximum operating pressure of 6 bar. A grid has been introduced with different blockage ratios (BR = 54%, 61% & 67%) in order to generate turbulence inside the combustor for the experiment. Optical access is provided via quartz windows on three sides of the combustion chamber. Finite Element Analysis (FEA) is done in order to verify the structural integrity of the combustor at rated conditions. In order to increase the inlet temperature of the air, a heating section was designed to use commercially available in-line heaters. Separate cooling subsystems have been designed for chamber cooling and exhaust cooling. The LabVIEW software interface has been selected as the control mechanism for the experimental setup. A 10 kHz Time Resolved Particle Image Velocimetry (TR-PIV) system and a 3 kHz Planer Laser Induced Fluorescence (PLIF) system have been integrated with the system in order to diagnose the flow field and the flame respectively. The primary understanding of the flow field inside the combustor was achieved through the use of Detached Eddy Simulation (DES) by using commercially available software package ANSYS FLUENT. Preliminary validation is done by 10 kHz TR-PIV technique. Both qualitative and quantitative analysis have been done for CFD and experiment. Major flow parameters such as average velocity, fluctuation of velocity, kinetic energy, and turbulent intensity have been calculated for two distinct Reynolds number (Re = 815 & 3500). PIV results are compared with CFD results which show significant agreement with each other.

High Temperature Flow Solver For Aerothermodynamics Problems, Huaibao Zhang

Theses and Dissertations--Mechanical Engineering

A weakly ionized hypersonic flow solver for the simulation of reentry flow is firstly developed at the University of Kentucky. This code is the fluid dynamics module of known as Kentucky Aerothermodynamics and Thermal Response System (KATS). The solver uses a second-order finite volume approach to solve the laminar Navier– Stokes equations, species mass conservation and energy balance equations for flow in chemical and thermal non-equilibrium state, and a fully implicit first-order backward Euler method for the time integration. The hypersonic flow solver is then extended to account for very low Mach number flow using the preconditioning and switch of …

Evaluation Of The Performance Of Various Turbulence Models For Accurate Numerical Simulation Of A 2d Slot Nozzle Ejector, Colin Graham

McKelvey School of Engineering Theses & Dissertations

With the development over the last several decades, accurate Computational Fluid Dynamics (CFD) modeling has now become an essential part in the analysis and design of various industrial products where the fluid flow plays an important role. The goal of this thesis is to apply the CFD technology to the analysis of a 2D slot nozzle ejector which has application in Short Take-off and Landing (STOL) aircraft and other future aerospace vehicles. In the nozzle-ejector configuration, the high speed air flow from the nozzle entrains the ambient air into a mixing chamber (ejector) as a means to create additional thrust …

Characterizing Cryogenic Propellant Flow Behavior Through A Cavitating Venturi In Comparison To Alternative Flow Control Mechanisms, Marjorie Adele Ingle

Open Access Theses & Dissertations

The work detailed is an investigation of the use of a cavitating venturi as both a flow control and metering device. This was achieved through the combination of actual experimentation and numerical modeling of the fluid behavior of both liquid water and liquid methane as it passes through the test article designed, developed, and validated here within this study. The discharge coefficient of the cavitating venturi was determined through weigh flow calibration testing to determine an average mass flow rate. Turbine flow meter flow rate readings were used as a point of comparison and the discharge coefficient was computed. The …

Essentially Analytical Theory Closure For Space Filtered Thermal-Incompressible Navier-Stokes Partial Differential Equation System On Bounded Domains, Mikhail Alexandrovich Sekachev

Doctoral Dissertations

Numerical simulation of turbulent flows is identified as one of the grand challenges in high-performance computing. The straight forward approach of solving the Navier-Stokes (NS) equations is termed Direct Numerical Simulation (DNS). In DNS the majority of computational effort is spent on resolving the smallest scales of turbulence, which makes this approach impractical for most industrial applications even on present-day supercomputers. A more feasible approach termed Large Eddy Simulation (LES) has evolved over the last five decades to facilitate turbulent flow predictions for reasonable Reynolds (Re) numbers and domain sizes. LES theory uses the concept of convolution with a spatial …

Development Of Cfd Models For The Purposes Of Exploring Free Surface Wave Phenomena, Leonard P. Stoehr

Masters Theses

With the push for finding alternative, green energy sources, the harnessing of energy from ocean and lake waves is becoming a more researched field. To fully understand the behavior of wave interactions and optimize designs to extract this energy, it is necessary to develop computer models that can accurately replicate this behavior. A case is presented in which previous work done using the wave tank found in the Western Michigan University fluids lab is examined. The case involves harnessing the energy generated by ocean waves through the usage of plates of different shapes resting horizontally on the water’s surface. The …

Aerodynamic Analysis And Drag Coefficient Evaluation Of Time-Trial Bicycle Riders, Peter Nicholas Doval

Theses and Dissertations

Evaluation of drag coefficient often requires wind tunnel experiments and can be prohibitively expensive if not impossible for large objects or systems. Computational Fluid Dynamics (CFD) aerodynamic analysis offers an alternative approach and can be used as a very effective design tool in many industries: automotive, aerospace, marine, etc. The main objective of this research is to investigate feasibility of using non-contact digitizers for developing finite element models of large objects for subsequent CFD analysis. The developed methodology is applied to investigation of time-trial bicycle rider efficiency. Companies competing in this class of racing spend millions trying to optimize bicycle …