Mechanical Engineering Commons^™

Benchmarking Of A Sco2 Heat Exchanger Flow Loop, David Velasco

Doctoral Dissertations and Master's Theses

Heat transfer of supercritical carbon dioxide (sCO2) was studied experimentally by commissioning a sCO2 flow loop featuring a horizontal tube-in-tube counterflow heat exchanger with a circular cross section. The main objective was to establish experimental heat transfer research capabilities for sCO2 at Embry-Riddle Aeronautical University’s (ERAU) Thermal Science Lab. sCO2 experiences a drastic change in thermophysical properties near its critical point that results in unique heat transfer characteristics. The high pressures at which sCO2 exists make the large gradients in thermophysical and transport properties difficult to study, experimentally and numerically. However, understanding the heat transfer characteristics and thermophysical behavior of …

Comparison Of Methods For Estimating Instantaneous Turn Radius Of Ackermann Steering Vehicles, Kenneth Gennaro Stutts

Doctoral Dissertations and Master's Theses

The instantaneous turn radius of an Ackermann steering vehicle is the distance to a point in space about which the vehicle will travel in an arc during a turn. There are at least six ways to estimate instantaneous turn radius and each method uses different inputs and has distinct advantages and disadvantages. In this thesis, six different methods will be used to estimate the instantaneous turn radius of a vehicle traveling on a closed circuit. This testing will clarify similarities and differences between the methods. This thesis clarifies which method will be the most appropriate for a given set of …

Design And Characterization Of A High Pressure Flow Loop For Heat Transfer Experiments Of Supercritical Carbon Dioxide, Joseph Sauerbrun

Doctoral Dissertations and Master's Theses

Supercritical carbon dioxide (sCO2) sees heightened heat transfer characteristics near its critical point due to its drastically changing thermophysical properties. Conventional single phase heat transfer theory was not developed to capture this nonlinear variation in properties and cannot predict the heat transfer characteristics of sCO2 to a practical level useful for design. To delve deeper into the behavior near the critical point and shed light on this crucial phenomenon, a state-of-the-art closed flow loop was developed. This setup enabled convective heat transfer experiments of sCO2 under diverse boundary conditions and test section geometries. Key components of the loop include the …

Explorations In Monocular Distance And Ranging (Modar) Techniques For Real-World Applications, Devon Vail

Doctoral Dissertations and Master's Theses

In this work, an initial prototype of a monocular camera system capable of retrieving depth-from-focus using a liquid focus-tunable lens is constructed out of hobby-grade photography equipment. This concept has been explored previously in laboratory settings using specialized equipment; this work seeks to determine the feasibility of retrieving depth-from-focus using commercially available components. To achieve this, an iterative exploration of existing techniques was performed to verify their utility in the final ensemble of processes to retrieve depth from 2D images. Initially, blurry images were simulated by applying Gaussian blur to test images to verify the functionality of a Laplacian of …

The Influence Of Mixing Duct Length And Phase Of Flight On Wall Temperatures Of A Rocket Based Combined Cycle Engine In Ejector And Air-Augmented Modes, Jonathan Grow

Doctoral Dissertations and Master's Theses

Rocket Based Combined Cycle (RBCC) engines have been theorized as a possible means of powering launch vehicles and high-speed atmospheric vehicles. By incorporating aspects of both air-breathing and rocket propulsion, RBCC engines promise up to a 230 % increase in specific impulse over traditional chemical rocket propulsion by entraining a secondary flow of atmospheric air and mixing it with the exhaust of a rocket motor. Students within the Embry-Riddle Future Space Explorers and Developers Society (ERFSEDS) identified a
problem of excessive heating and structural failure of the mixing duct during launch and transonic flight of a student-built flight test vehicle. …

Aeroponic System Optimization For Butterhead Lettuce Growth And Future Sustainability Using Flow Blurring Atomization, Taylor J. Johnson

Doctoral Dissertations and Master's Theses

The global population has grown by 6 billion people over the last century and is trending toward 9.7 billion people by the year 2050. Agriculture accounts for 70% of global fresh water usage. Technology must be developed to accommodate the increase of food production demanded by the growing global population and the subsequent increase in water usage. Aeroponic technology is a water-efficient vertical farming technology that can reduce water usage by 90% by suspending plant roots in air within a controlled chamber and supplying atomized droplets of a water-nutrient solution directly to the roots.

This study simultaneously tests six droplet …

Modeling, Control, And Hardware Development Of A Thrust-Vector Coaxial Uav, Andrew North

Doctoral Dissertations and Master's Theses

This thesis introduces a unique thrust vector coaxial unmanned aerial vehicle (UAV) configuration and presents a comprehensive investigation encompassing dynamics modeling, hardware design, and controller development. Using the Newton-Euler method, a dynamic model for the UAV is derived to gain in-depth insights into its fundamental flight characteristics. A simple thrust model is formulated and modified by comparing it with data obtained from vehicle testing. The feasibility of manufacturing such a vehicle is assessed through the development of a hardware prototype. Finally, a linear state feedback controller is designed and evaluated using the non-linear dynamics model. The results demonstrate successful validation …

Atmospheric Carbon Capture: A Review On Current Technologies And Analysis Of Energy Consumption For Various Direct Air Capture (Dac) Systems, Jennifer Perskin

Doctoral Dissertations and Master's Theses

Carbon dioxide (CO₂) capture is a crucial approach to reducing greenhouse gases in the atmosphere to directly combat climate change. Major components of the technology to desublimate CO₂ at cryogenic temperatures are mature and have the potential to be applied to build large Arctic/Antarctic direct-air CO₂ capture plants. Pressure swing adsorption another gas separation technique used in industry today that can be modified for atmospheric carbon capture. The discussion of energy consumption for cryogenic and combined direct air capture systems is explored in this study. The investigation of precompression of atmospheric air for a direct-air capture …

Deep Learning Of Semantic Image Labels On Hdr Imagery In A Maritime Environment, Charles Montagnoli

Doctoral Dissertations and Master's Theses

Situational awareness in the maritime environment can be extremely challenging. The maritime environment is highly dynamic and largely undefined, requiring the perception of many potential hazards in the shared maritime environment. One particular challenge is the effect of direct-sunlight exposure and specular reflection causing degradation of camera reliability. It is for this reason then, in this work, the use of High-Dynamic Range imagery for deep learning of semantic image labels is studied in a littoral environment. This study theorizes that the use HDR imagery may be extremely beneficial for the purpose of situational awareness in maritime environments due to the …

Experimental And Numerical Analysis Of A Commercial Phase Change Material Melting At Different Inclinations, Andrew Heiles

Doctoral Dissertations and Master's Theses

The study of various phase change materials (PCM), experimentally and numerically, have been completed over the past several years to address their feasibility and potential when used in latent heat thermal energy storage (LHTES) systems for a variety of potential applications. Previous studies have investigated changes into the type of PCM used in the system as well as the system configuration, ranging from boundary conditions to internal and external geometries and orientations of the system. The present study focused on conducting experiments at different inclination angles and isothermal wall temperatures with the organic PCM PureTemp37, and continued with a numerical …

Assessing High Dynamic Range Imagery Performance For Object Detection In Maritime Environments, Erasmo Landaeta

Doctoral Dissertations and Master's Theses

The field of autonomous robotics has benefited from the implementation of convolutional neural networks in vision-based situational awareness. These strategies help identify surface obstacles and nearby vessels. This study proposes the introduction of high dynamic range cameras on autonomous surface vessels because these cameras capture images at different levels of exposure revealing more detail than fixed exposure cameras. To see if this introduction will be beneficial for autonomous vessels this research will create a dataset of labeled high dynamic range images and single exposure images, then train object detection networks with these datasets to compare the performance of these networks. …

Thermal Boundary Condition Effects On Local Supercritical Co2 Heat Transfer Trends In Tubes, Nicholas C. Lopes

Doctoral Dissertations and Master's Theses

Supercritical carbon dioxide (sCO2) is a promising heat transfer fluid for the refrigeration and power generation industries due to its unique thermal properties and low environmental impact. To understand it as an alternative to traditional working fluids, the thermophysical and heat transfer phenomena of sCO2 are often studied using simplified geometries (tubes). Focus has been placed on investigating averaged heat transfer trends under an array of flow conditions with either a constant wall heat flux, constant wall temperature, or conjugate thermal boundary condition. Less emphasis has been placed on studying local sCO2 heat transfer developments. Tubular sCO2 numerical models that …

Neural Network Fusion Of Multi-Modal Sensor Data For Autonomous Surface Vessels, David J. Thompson

Doctoral Dissertations and Master's Theses

Autonomous surface vessels (ASV) can potentially improve the safety of vessels traditionally operated by humans. Despite advancements in autonomous on-road vehicles, many of these advancements have yet to be realized for ASVs. This is primarily due to lacking ASV sensing platforms and public datasets for ASV-based perception research. To that end, this dissertation demonstrates the design of a synchronized multi-modal sensing platform for ASVs utilizing GPS/INS, LiDAR, LWIR cameras, HDR camera, and high-resolution cameras. The sensing platform is designed to maximize the overlap of sensors for multi-modal research and provides accurate intrinsic and extrinsic calibration between each sensor. Furthermore, the …

Additive Manufacturing For Phase Change Thermal Energy Storage And Management, Thomas B. Freeman

Doctoral Dissertations and Master's Theses

Phase change materials can enhance the performance of energy systems by time shifting or reducing peak thermal loads. Certain electronic devices such as batteries, laser systems, or electric vehicle power electronics are highly transient and require pulse heat dissipation. Heat sinks, or thermal management devices made of a phase change material can absorb large heat spikes while maintaining a constant temperature. Additive manufacturing techniques hold tremendous potential to enable co-optimization of material properties and device geometry, while potentially reducing material waste and manufacturing time. Recently, a few efforts have emerged that employ additive manufacturing techniques to integrate a phase change …

Biomass Characterization And Insulation Optimization Studies, Hussein Awad Kurdi Saad

Doctoral Dissertations and Master's Theses

This study indicates how biomass materials can be effectively used as naturally sustainable alternatives to insulation materials. Barley grains and oak leaves, straw, and jute are collected, and crushed into powders/ chopped pieces. The physical characteristics are measured to characterize each powder. The biomass powder reinforced composites are manufactured in varying weight ratios. The density and thermal conductivity of composite materials are measured. The properties of composites compared to those of commercial insulation materials are found to be close to them. Furthermore, genetic algorithms (GA) can be used to achieve multi-objective optimization entailing maximizing insulation (minimizing heat transfer) and simultaneously …

Effect Of Passive Clean Air Injection Into The Wake Region Of A Moving Ground Vehicle, Angelos Kaminis

Doctoral Dissertations and Master's Theses

The wake region on a moving ground vehicle is responsible for 70% of the aerodynamic drag when the speed of 90km/h is achieved. The topic of wake region manipulation has been revisited multiple times and with varying techniques. When manipulating the flow utilizing a fully passive method, pressure drag can be reduced, increasing the overall performance of the vehicle. To ensure high velocity fluid injection, a venturi shaped roof was implemented with an inlet size of 352mm x 12.7mm, and 2 outlets of size 88.011mm x 25.4mm resulting in an area of 4,470.959 for both inlet and outlet to maintain …

Finite Element Model Of The Pediatric Hip Joint During The Barlow Maneuver, Christina M. Zlock

Doctoral Dissertations and Master's Theses

Developmental Dysplasia of the Hip is the dysplasia or dislocation of an unstable femoral head in the acetabulum of the pelvis. This is a result of an abnormal or underdeveloped growth of the acetabulum and triradiate cartilages and/or an out of place and uncentered femoral head in the acetabulum. This underdevelopment, if not diagnosed and treated at an early age, may lead to abnormal and pain and osteoarthritis later in life. A common step in diagnosis is to perform a physical examination of the hip, one method is the Barlow maneuver.

The aim of the project is to use healthy …

Water Based Soil Fluidization Using A Soft Eversion Robot, James E. Hand

Doctoral Dissertations and Master's Theses

Soft robotics, a form of robotics that incorporates nonrigid components, continues to grow in scope, system design, and application. A recent addition to this field is the Vine Robot platform, a bio-inspired robot designed by Stanford University in 2017. Its method of movement, known as eversion, closely resembles the way that a vine grows along a tree, giving it its name. The focus of this research was to take its proven abilities of underwater vine-like movement and soil fluidization, a process where granular materials are converted from a solid-like state to a fluid-like state, to create an underwater eversion robot …

A Meshless Approach To Computational Pharmacokinetics, Anthony Matthew Khoury

Doctoral Dissertations and Master's Theses

The meshless method is an incredibly powerful technique for solving a variety of problems with unparalleled accuracy and efficiency. The pharmacokinetic problem of transdermal drug delivery (TDDD) is one such topic and is of significant complexity. The locally collocated meshless method (LCMM) is developed in solution to this topic. First, the meshless method is formulated to model this transport phenomenon and is then validated against an analytical solution of a pharmacokinetic problem set, to demonstrate this accuracy and efficiency. The analytical solution provides a locus by which convergence behavior are evaluated, demonstrating the super convergence of the locally collocated meshless …

Experimental And Numerical Investigation Of Lauric Acid Melting At Suboptimal Inclines, Casey J. Troxler

Doctoral Dissertations and Master's Theses

Validation experiments are the baseline for completing numerical studies for engineering design. Applications of the enthalpy-porosity model have expanded in research with the growth of new technologies such as metal additive manufacturing or the renewed interest in thermal energy storage for supplementing renewable energy. A simplified experiment examining the melting behavior of lauric acid from an isothermal surface has become a common case for validating the performance of numerical models. Several studies of this rectangular experiment have been repeatedly used as model validation in a variety of problem conditions.

The first part of this study presents experimental data for the …

Numerical Simulation Of A Cryogenic Spray, Neel Kishorkumar Shah

Doctoral Dissertations and Master's Theses

Cryogenic sprays have many applications in modern engineering. Cooling of electronic equipment subject to high heat flows, surgical ablation of gastrointestinal mucosae or orbital maneuvering are a few examples of their versatility. However, the atomization of a cryogenic liquid is a complex process. During such an event, aerodynamic effects associated with secondary atomization are further affected by thermodynamic flashing. A better understanding of the characteristics of cryogenic sprays is then necessary to allow for improved design and optimization in applications. The overarching objective of this study is to document such characteristics. The numerical simulation was performed over cryogenic nitrogen spray …

State-Of-The-Art Of Thermal Control Solutions To Establish A Modular, Multi-Orbit Capable Spacecraft Thermal Management System Design Methodology, Robert C. Consolo Jr

Doctoral Dissertations and Master's Theses

Today, the exploration and exploitation of space continues to become a more common occurrence. All types of spacecraft (S/C) utilize various types of thermal management solutions to mitigate the effects of thermal loading from the unforgiving vacuum of space. Without an appropriately designed thermal system, components on-board the S/C can experience failure or malfunction due to fluctuations in temperatures either beyond the designed operational parameters or unstable oscillating temperatures. The purpose of this study is to perform a comprehensive review of technologies available today that are being used for thermal management onboard S/C in addition to investigating the means to …

Dynamic Modeling Of Soft Robotic Dielectric Elastomer Actuator, Abdullah De Jesus El Atrache Ceballos

Doctoral Dissertations and Master's Theses

Dielectric elastomers actuators (DEAs) are among the preferred materials for developing lightweight, high compliance and energy efficient driven mechanisms for soft robots. Simple DEAs consist mostly of a homogeneous elastomeric materials that transduce electrical energy into mechanical deformation by means of electrostatic attraction forces from coated electrodes. Furthermore, stacking multiple single DEAs can escalate the total mechanical displacement performed by the actuator, such is the case of multilayer DEAs. The presented research proposes a model for the dynamical characterization of multilayer DEAs in the mechanical and electrical domain. The analytical model is derived by using free body diagrams and lumped …

Design, Development, And Testing Of Research Payloads On Various Suborbital Flight-Test Platforms, Vijay Vishal Duraisamy

Doctoral Dissertations and Master's Theses

With recent advances in the commercial space industry, suborbital payload launches have become more common and accessible to researchers actively seeking solutions for problems involving prolonged space travel and future missions to Moon and Mars. Suborbital payload missions compared to orbital launches are less expensive and offer faster turnaround times; however, the novelty of this domain provides unique challenges. This multidisciplinary research effort aims to tackle some of these challenges by detailing the design, development, and testing techniques followed in the successful launch and recovery of payload experiments in currently active and upcoming suborbital launch vehicles. The research methodology involves …

In-Vitro And In-Silico Investigations Of Alternative Surgical Techniques For Single Ventricular Disease, Arka Das

Doctoral Dissertations and Master's Theses

Single ventricle (SV) anomalies account for one-fourth of all cases of congenital Heart disease. The conventional second and third stage i.e. Comprehensive stage II and Fontan procedure of the existing three-staged surgical approach serving as a palliative treatment for this anomaly, entails multiple complications and achieves a survival rate of 50%. Hence, to reduce the morbidity and mortality rate associated with the second and third stages of the existing palliative procedure, the novel alternative techniques called “Hybrid Comprehensive Stage II” (HCSII), and a “Self-powered Fontan circulation” have been proposed. The goal of this research is to conduct in-vitro investigations to …

Use Of Machine Learning For Automated Convergence Of Numerical Iterative Schemes, Leonardo A. Bueno-Benitez

Doctoral Dissertations and Master's Theses

Convergence of a numerical solution scheme occurs when a sequence of increasingly refined iterative solutions approaches a value consistent with the modeled phenomenon. Approximations using iterative schemes need to satisfy convergence criteria, such as reaching a specific error tolerance or number of iterations. The schemes often bypass the criteria or prematurely converge because of oscillations that may be inherent to the solution. Using a Support Vector Machines (SVM) machine learning approach, an algorithm is designed to use the source data to train a model to predict convergence in the solution process and stop unnecessary iterations. The discretization of the Navier …

Desalination For Sustainable Water Production With An Emphasis On Low Pressure Distillation, Jessica Vivian Savage

Doctoral Dissertations and Master's Theses

Freshwater resources depletion is a growing concern. This freshwater scarcity motivates research into seawater desalination as a means for alleviating the stresses on water demands. The primary methods of desalination include filtration and distillation. This paper explores the potential energy savings of vacuum distillation for seawater desalination to reduce the amount of energy needed to achieve phase change.

Depending on the vacuum boiler design, the vaporization mechanism may be boiling, evaporation, or cavitation. There is very little literature on cavitation that involves mass transfer, so cavitation is not developed here. This thesis focuses on standard models for boiling and evaporation …

Validation Of A Two-Dimensional Clinostat Design To Provide Functional Weightlessness To Custom Gas Exchange Vessels, Collin R. Topolski

Doctoral Dissertations and Master's Theses

Understanding the impacts of microgravity on bacteria is vital for successful long duration space missions. In this environment, bacteria have been shown to become more virulent, more resistant to antibiotics and form more biofilms. To learn more about these phenomena, many experiments must be sent to the International Space Station, which is cost- and time prohibitive. Instead, the use of ground-based analogs is advantageous to define preliminary results that can later be verified with a space-based experiment. This research explored the development of an innovative 2D clinostat for simulating microgravity using bacteria. Computational fluid dynamics, standards established by previous literature …

Automated Scenario Generation Using Halton Sequences For The Verification Of Autonomous Vehicle Behavior In Simulation, Andrew Ferree

Doctoral Dissertations and Master's Theses

As autonomous vehicles continue to develop, verifying their safety remains a large hurdle to mass adoption. One component of this is testing, however it has been shown that it is impractical to statistically prove an autonomous vehicle’s safety using real-world testing alone. Therefore, simulation tools and other virtual testing methods are being employed to assist with the verification process. Testing in simulation still faces some of the challenges of the real world, such as the difficulty in exhaustively testing the system in all scenarios it will encounter. Manual scenario creation is time consuming and does not guarantee scenario coverage. Pseudo-random …

A Comparative Study Between 6 Degree-Of-Freedom Trajectory Model And Modified Point Mass Trajectory Model Of Spinning Projectiles, Ange Du

Doctoral Dissertations and Master's Theses

For spinning projectiles, the 6 Degree-of-Freedom model can closely capture their trajectories with high accuracy and details. However, it comes with the drawbacks of long computation time and needing many aerodynamic coefficients which can be hard to obtain. The Modified Point Mass Trajectory Model was introduced as a simplified solution. This work compares them with each other, and with some more conventional methods. A program is developed to simulate and visualize trajectories. With some augmentations, the Modified Point Mass model is able to generate comparable results in most cases, but not including special cases such as when the projectile is …