Mechanical Engineering Commons^™

Cfd Model For Ventilation In Broiler Holding Sheds, Christian Heymsfield

Biological and Agricultural Engineering Undergraduate Honors Theses

Broiler production in Arkansas was valued at over $3.6 billion in 2013 (University of Arkansas Extension of Agriculture). Consequently, improvement in any phase of the production process can have significant economic impact and animal welfare implications. From the time poultry leave the farm and until they are slaughtered, they can be exposed to harsh environmental conditions, both in winter and in summer. After road transportation, birds are left to wait in holding sheds once they arrive at the processing plant, for periods of approximately 30 minutes to two hours. This project was interested in this holding shed waiting time during …

Optical Analysis And Fabrication Of Micro And Nanoscale Plasmonically Enhanced Devices, Avery M. Hill

Mechanical Engineering Undergraduate Honors Theses

Plasmonic nanostructures have been shown to act as optical antennas that enhance optical devices due to their ability to focus light below the diffraction limit of light and enhance the intensity of the incident light. This study focuses on computational electromagnetic (CEM) analysis of two devices: 1) GaAs photodetectors with Au interdigital electrodes and 2) Au thin-film microstructures. Experiments showed that the photoresponse of the interdigital photodetectors depend greatly on the electrode gap and the polarization of the incident light. Smaller electrode gap and transverse polarization give rise to a larger photoresponse. It was also shown that the response from …

Improving Ventricular Catheter Design Through Computational Fluid Dynamics, Sofy Hefets Weisenberg

Masters Theses

Cerebrospinal fluid (CSF) shunts are fully implantable medical devices that are used to treat patients suffering from conditions characterized by elevated intracranial pressure, such as hydrocephalus. In cases of shunt failure or malfunction, patients are often required to endure one or more revision surgeries to replace all or part of the shunt. One of the primary causes of CSF shunt failure is obstruction of the ventricular catheter, a component of the shunt system implanted directly into the brain's ventricular system. This work aims to improve the design of ventricular catheters in order to reduce the incidence of catheter obstruction and …

Senior Design Project, Lee F. Collier 7737457, Amy Albaugh, Jacob Walker, Justin Church

Chancellor’s Honors Program Projects

No abstract provided.

Automated Fusegrade Testing Machine, Natalie A. Rayfield, Peter Trzil, Dylan Moore, Colin Roberson, Haley Register

Chancellor’s Honors Program Projects

No abstract provided.

Numerical Investigation Of Full Scale Thunderstorm Downbursts: A Parametric Study And Comparison To Meteorological Model, Christopher Oreskovic

Electronic Thesis and Dissertation Repository

A series of Large Eddy Simulations using an atmospheric meteorological cloud model have been used to investigate the important geometric and thermal parameters that influence a thunderstorm downburst outflow, as it pertains specifically to the idealized cooling source model. A separate set of Large Eddy Simulations make use of the same idealized cooling source model, in a realistic atmospheric base state using real field sounding data, in an attempt to make a quantifiable comparison to a downburst from a full cloud simulation. Randomness has been added to the cooling source forcing function to mimic the thermal variation in a real …

Design And Analysis Of A Lift Assist Walker, Deep P. Shah

Master's Theses

Walkers provided stability to the elderly but cannot assist a person from sitting to standing. The objective of this project is to present the design and analysis of a lift assist walker. This report discusses the design and analysis of a collapsible lift assist walker capable of lifting a patient up to 250 lbs. from seated to standing in under 10 seconds. The designed walker utilized a two stage scissor mechanism with a gas spring assisted embedded linear actuator.

Development Of An Autonomous Robotic Mushroom Harvester, Nikita Alexeevich Kuchinskiy

Electronic Thesis and Dissertation Repository

The process of development of a new robot is one of the modern technological arts. This process involves multiple complex steps and recursive approach. In this project, a solution for automatic harvesting of mushrooms is developed. In order to design an effective solution, it is necessary to explore and take into consideration the limitations of grasping very soft and fragile objects (particularly mushrooms). We will elaborate several strategies of picking and analyze each strategy to formulate the design requirements, develop a solution, and finally, evaluate the efficiency of the proposed solution in actual farm conditions for real mushrooms. The mushroom …

Orchard Bin Atv Trailer, Neil F. Leitz

All Undergraduate Projects

A local orchardist was experiencing a problem that was being caused by their lack of apple picking bin moving equipment. The orchardist needed a well-engineered solution to this lack of equipment. The solution arrived at was a five bin trailer. There were multiple design requirements for this trailer, including the device needing to be able to interface with an ATV, be able to be loaded by hand, be able to carry five bins, and not exceed a budget of $750. While perfecting the design of the trailer, a number of different disciplines were utilized, which included dynamics, kinematics, static loading …

Grant County Public Utilities District - Rotor Pole Lifting Device, Baylie Johnson

All Undergraduate Projects

Grant County Public Utilities District is planning a rehabilitation of all turbine and generator units at Priest Rapids Dam beginning in August 2016. After the generator rotor is removed from the unit, the rotor poles must be removed from the rotor. They are oriented vertically in the rotor and horizontally on the floor and in shipping containers. The objective of this project is to design, manufacture and test a lifting and a turning device for Priest Rapids Dam’s generator rotor poles. The lifting device was designed to attach a 3500 pound rotor pole to a crane and lift it. The …

Asme Mini Rc Baja: Drivetrain, Jason M. Moore

All Undergraduate Projects

Title and author: ASME mini RC Baja Drivetrain by Jason Moore; partner Mike Cox. (Engineering Technologies, Safety, and Construction)

Abstract/Artists Statement: The issue that this project is concerned with is how to design and build a drivetrain, steering and suspension systems for an RC car. The systems must be simple and functional. Furthermore, these systems will be designed to fit on a small chassis and not interfere with each other. They also need to be strong and durable enough to propel the car forward and maneuver through various obstacles and be built in a way that is easy to take …

Shellfish Bag Maker, Trevor R. Reher

All Undergraduate Projects

When commercially harvesting shellfish specifically clams and oyster, plastic mesh bags are commonly used to place shellfish in after harvesting on beaches. The issues is taking the raw bag material used for harvest and cutting it to a specified length. The material comes on a 2000 ft. spool and needs to be cut to a length of 54 in. Using an existing but out dated machine, a bench mark was made that the new design must be 10% more efficient for the customer to invest money into building the machine. Using mechanical machine design and computer designing software the machine …

Multiple Apple Box Lift 1/10th Scale Model, Kyle J. Burlingame

All Undergraduate Projects

Title and Author: 1/10th Scale Multiple Apple Box Lift by Kyle Burlingame (Engineering Technologies, Safety, and Construction) Abstract/Artist statement: A 1/10th scale Multiple Apple Box Lift was designed and built as a proof of concept for a full scale device. The Multiple Apple Box Lift was designed to meet a customer’s requirements and to be presented at SOURCE. This device lifts the top half of the stacked apple boxes on a pallet in order to allow access to the boxes in the middle of the stack. The device can be manually operated by two people while in-between narrow rows of …

Flag Raising Device, Josh Quintero

All Undergraduate Projects

The motivation for this project stems from a lifetime of boating with father Richard Jones. One problem that many people encounter, including Richard, was when towing someone behind a boat, is the difficulty with handling the warning flag. This flag is used to show other surrounding boats that someone has fallen into the water behind their boat. This warns other boats to stay far away from that area to keep safe from running over the swimmer. Although, when holding the flag in the boat, it can be hard to see at times. The boat driver, or other people standing in …

Hydraulic Sprayer Boom Upgrade, Chad R. Omlin

All Undergraduate Projects

Title and Author: Agriculture sprayer hydraulic boom upgrade by Chad Omlin (engineering Technologies, Safety, and Construction)

Abstract: Today’s agriculture industry is all about being the most efficient with your time, land, employees, and machinery. One thing that has made farming more efficient has been the use of hydraulics. Having a sprayer unit with manual booms is not being efficient with your time and/or employees. To make the sprayer unit more efficient, hydraulic cylinders were added. Sketched solutions were analyzed using statics and mechanics of materials principles. Drawings were completed for the successful analysis solutions. Solid works software was used to …

The Pneumatic Leg Extension, David G. Sedano

All Undergraduate Projects

In recent years, reaching altitudes that are higher than your normal-height has evolved from pure amusement to an “in-demand” necessity out in the field. Means of achieving greater than normal height range from wooden poles to aluminum stilts. The era of ladders and other extension methods are slowly fading away. There are many designs in the market that focus on different factors to make a stilt. As other designs focus on one or two enhancements, the pneumatic leg extension’s objective is to improve all aspects of the stilt. This radical new design differs greatly from traditional stilt designs. The pneumatic …

Asme Mini-Baja Rc Car (Steering And Suspension Systems), Michael E. Cox

All Undergraduate Projects

The issue that this project is concerned with is how to design and build a drivetrain, steering and suspension systems for an RC car. The systems must be simple and functional. Furthermore, these systems will be designed to fit on a small chassis and not interfere with each other. They also need to be strong and durable enough to propel the car forward and maneuver through various obstacles and be built in a way that is easy to take apart and repair quickly. These design problems were approached using basic mechanical design concepts such as gear kinematics, spur and bevel …

Design Features And Optimization Of Profile Extrusion Dies, Abhishek Sai Erri Pradeep

Dissertations, Master's Theses and Master's Reports

This report deals with design of dies used in the plastic extrusion industry. The design methodology for extrusion dies has evolved over the years with advancement of computing technology. However, the design process is still heavily dependent on the experience of the die designer, and hence is still considered to be more of an art than science. Even for an experienced designer, the time required to design the die and perform consecutive fine tuning iterations is high. In this report, a proprietary optimization code for extrusion dies, .developed by Plastic Flow LLC, was tested and shown to be advantageous over …

Conversion Casting: Adapter Hub, Joseph M. Coup

All Undergraduate Projects

The concept of conversion casting makes manufacturing major components much more efficient with regards to time and cost. The conversion cast of the adapter hub used in the Victair Mistifier is a major component that requires 8 hours to machine. The existing hub starts from steel stock and then that block of steel is placed into a CNC machine and coded in to create the adapter hub. The manufacturing method changes to a casting for the adapter hub will create a replicated part that requires 1.5 hours of post machining. The intricate design makes a conversion to casting more effective …

Methodology For Analyzing Epoxy-Cnt Phononic Crystals For Wave Attenuation And Guiding, Madhu Kolati

Dissertations, Master's Theses and Master's Reports

Phononic crystals (PhnCs) control, direct and manipulate sound waves to achieve wave guiding and attenuation. This dissertation presents methodology for analyzing nanotube materials based phononic crystals to achieve control over sound, vibration and stress mitigation. Much of the analytical work presented is in identifying frequency band gaps in which sound or vibration cannot propagate through these PhnCs. Wave attenuation and mitigation analysis is demonstrated using finite element simulation. Engineering principles from current research areas of solid mechanics, solid-state physics, elasto-dynamics, mechanical vibrations and acoustics are employed for the methodology. A considerable effort is put to show that these PhnCs can …

A Nocsae Drop Test/ 3d-Fem Study On The Relationship Between Kinematic Response Of The Head, Head Impact Contact Pressure (Hicp) And Kinetic Response Of The Brain To Delineate The Risk Of Traumatic Brain Injuries (Tbi)., Raghavendra Krishna Tej Bhamidipati

Dissertations, Master's Theses and Master's Reports

How many times have you seen a person slip and fall down and had a good laugh about it? How many times we slip and fall down on the floor and got up and walked away thinking everything is normal? Probably we might wonder “Are drops which occur at a small height dangerous?” Yes, they can be. Brain injuries are main reason for the fatality in youth [1], and low level falls are one of the most neglected and understated injuries.

The main objective of this study is to study the response of the brain for low level falls from …

3d Infrastructure Condition Assessment For Rail Highway Applications, Teng Wang

Theses and Dissertations--Civil Engineering

Highway roughness is a concern for both the motoring public and highway authorities. Roughness may even increase the risk of crashes. Rail-highway grade crossings are particularly problematic. Roughness may be due to deterioration or simply due to the way the crossing was built to accommodate grade change, local utilities, or rail elevation. With over 216,000 crossings in the US, maintenance is a vast undertaking. While methods are available to quantify highway roughness, no method exists to quantitatively assess the condition of rail crossings. Conventional inspection relies on a labor-intensive process of qualitative judgment. A quantifiable, objective and extensible procedure for …

Design And Fabrication Of A Suspension Rig, Abhijith Geo Philip

Dissertations, Master's Theses and Master's Reports

Owing to its placement under the vehicle body, the suspension system is one of the parts of the vehicle which are difficult to comprehend completely, albeit being a vital component. For demonstrating the working of a suspension system, a physical model in which one can actually see the movement of all the components would be a great tool. A Mustang II independent front suspension system was purchased from Heidts Engineering Performance and a rig that can emulate some of the real world situations of vehicle suspension action was designed and fabricated. All the components are accessible and conditions like bounce, …

Smart Coffee Table, Matthew Owens

Williams Honors College, Honors Research Projects

This report documents the process I followed while working on my senior design project. It includes how I decided to build a Smart Coffee Table, my engineering process, the design of all features and mechanical components, relevant research necessary to complete the project, the performance of the structures, the methods for controlling and powering the table, and any problems along the way. Over the course of the last two semesters, I learned valuable lessons pertaining to working on a project from start to finish as an individual rather than in a group.

The University Of Akron Human Powered Vehicle Team, Maria E. Rizzo, Andrew J. Derhammer, Christopher M. Trowbridge, Timothy M. Nutt, Joseph R. Boyd, Jeremy W. Marcum, Jonathan E. Adams, Donald G. Haiss, Julia Wood, Brian D. Goshia, Scott T. Fagan, Joshua D. Everhard, Rebecca L. Slivka

Williams Honors College, Honors Research Projects

The University of Akron Human Powered Vehicle Team’s 2016 vehicle, Klokan, was designed, manufactured and tested with safety, reliability, performance and ease of use in mind. The vehicle is a fully faired tadpole trike with a lightweight aluminum frame constructed from 6061-T6 tubing having a total weight of 8.9 lbs. To complement the lightweight frame, the fairing is constructed from polycarbonate, PETG and carbon fiber strips which combine into a lightweight, easy to manufacture weather barrier and aerodynamic structure. Klokan was designed to be a safe and efficient mode of everyday transportation which ensures that riders are sufficiently protected by …

Optimization Of Formula Sae Electric Vehicle Frame With Finite Element Analysis, Alexander Prorok

Williams Honors College, Honors Research Projects

Optimization of Formula SAE Electric Vehicle Frame with Finite Element Analysis

Development Of Learning Objectives For An Undergraduate Computer-Aided Drafting And Design Animation Using The Delphi Technique, Gavin M. Wilk

Masters Theses

This study reflects on learning objectives created for an advanced computer aided drafting (CAD) learning module(s) or course with the emphasis on simulation and engineering animations. These objectives were derived by using the Delphi technique by access the support of a panel of subject matter experts (SME) from academia and industry that are interested in CAD. The results of this study are intended for the use of creating instructional modules for undergraduate studies.

A panel of experts were chosen through an electronic listserv of engineering and technology supporters. Two rounds of two different Delphi survey instruments were utilized to complete …

Design, Fabrication And Analysis Of An Auxiliary Power Unit On A Heavy-Duty Truck To Power The Hvac Systems Of The Truck During Driver Off-Duty Conditions, Rohan Milind Kalurkar

Dissertations, Master's Theses and Master's Reports

Currently, one of the biggest challenges the world is facing is energy insufficiency. One of the contributors to energy consumption in United States are the idling semi-trailer trucks. In May 2001, President Bush issued The National Energy Policy in which he directed The Environmental Protection Agency (EPA) and Department of Transportation (DOT) to reduce the idling of trucks. This was done in order to reduce energy consumption by lowering fuel consumption and emissions coming out of semi-trailer trucks in the United States of America.

This project deals with the efforts of installing an Auxiliary Power Unit (APU) as a device …

Finite Element Analysis And Topology Optimization Of Differential Case And Control Arm For Static And Fatigue Loading, Pankaj N. Kalan

Dissertations, Master's Theses and Master's Reports

Optimization of the automobile components can result in a significant decrease in vehicle weight, increase in fuel efficiency and reduction in environmental damage. For example, the lightweight vehicle production will save over 4.4×109 GJ of energy and 4.1×108 tons of CO2 over a 10 year period, compared to the current non-light weight vehicles. This equates to 890 billion miles or 42 billion gallons of gas savings (Wu 2016). This study evaluates the weight reduction possible by using manual and automatic (using Optistruct software) topology optimization processes. Optimization of a vehicle differential case done in this study shows that a weight …

Design Of A Mobile Underwater Charging System, Brian R. Page

Dissertations, Master's Theses and Master's Reports

Autonomous Underwater Vehicles (AUVs) are extremely capable vehicles for numerous ocean related missions. AUVs are energy limited, resulting in short mission endurance on the scale of hours to days. Underwater Gliders (UGs) are able to operate on the order of months to years by using nontraditional propulsion methods. UGs, however, are unable to perform missions requiring high speed or direct forward motion due to the nature of their buoyancy driven motion. This work reviews the current state of the art in recharging AUVs and offers an underwater recharging network concept at a significantly reduced cost to traditional methods. The solution …