Mechanical Engineering Commons^™

Effects Of Perforations On Internal Cathodic Protection And Recruitment Of Marine Organisms To Steel Pipes, Alexander John Paluzzi

Theses and Dissertations

Steel monopile support structures for offshore wind turbines require protection from corrosion on their external and internal surfaces. Cathodic protection (CP) works effectively to protect the external surfaces of monopiles, but internally, byproducts from aluminum sacrificial anode CP (SACP) and impressed current CP (ICCP) induce acidification that accelerates steel corrosion. This project investigated the effects of perforations on the performance of aluminum SACP and ICCP when used inside of steel pipes. Additionally, marine growth on the external and internal surfaces of the pipes was assessed to determine if CP byproducts affect marine organism development.

Two sealed and two perforated steel …

Evaluation Of Digital Twin Approaches For Thermal Modeling And Energy Optimization For Existing Buildings, Jason Bastie Muermann

Theses and Dissertations

Residential, commercial, and industrial building sectors in the United States were responsible for 42% of the nation’s consumption of 100.2 quadrillion BTUs of energy in 2019 [1]. 80% of the nation’s energy is sourced from fossil fuels, including coal, natural gas, and petroleum. Fossil fuels are known contributors to carbon emissions and climate change, making energy reduction vital. Consequently, New Jersey Department of Military and Veterans Affairs (NJDMAVA) is tasked with evaluating energy consumption and efficiency in all New Jersey Army National Guard (NJARNG) facilities, as mandated by TAG Policy Letter 18-5, Executive Order 13990, and the Energy Independence and …

Estimating Solar Energy Production In Urban Areas For Electric Vehicles, Shaimaa Ahmed

Theses and Dissertations

Cities have a high potential for solar energy from PVs installed on buildings' rooftops. There is an increased demand for solar energy in cities to reduce the negative effect of climate change. The thesis investigates solar energy potential in urban areas. It tries to determine how to detect and identify available rooftop areas, how to calculate suitable ones after excluding the effects of the shade, and the estimated energy generated from PVs. Geographic Information Sciences (GIS) and Remote Sensing (RS) are used in solar city planning. The goal of this research is to assess available and suitable rooftops areas using …

Effects Of Bonding Pressure And Lamina Thickness On Mechanical Properties Of Clt Composed Of Southern Yellow Pine, Cody S. Bates

Theses and Dissertations

This study produced cross-laminated timber panels at a range of four lamina thickness (5/8, 1, 1 1/8, and 1 1/4 inch) and three bonding pressures (50, 125, 200 psi), producing a total of 12 panels for mechanical testing. The goal of this study is to observe how the thickness and pressure trends affect the mechanical properties of CLT. Tests include flatwise bending, flatwise shear, internal-bond, and delamination. Results showed that bending MOE decreases as the panel thickness increases while bonding pressure had no significance. Bending MOR was less significant for the thickness and more significant for pressure compared to the …

Bonding Evaluation Of Graphene-Oxide Layers On Flexible Substrates, Maysam Rezaee

Theses and Dissertations

Flexible electronics are getting interest in development of field effects transducers such as biomedical health screening tools, structural health monitoring in infrastructures, aerospace, vehicular industries and cell phones. As a promising candidate for flexible electronics, graphene-based devices have been developed through exceptional electrochemical and thermomechanical properties of graphene. Reducing the graphene oxide enables creation of large scale devices through its high manufacturability. Same as other types of electronics, the bonding of sensing units to the substrate is significantly dependent to the deposition method used for the fabrication of device. In this study, the mechanical strength of reduced graphene oxide (rGO) …

Numerical And Experimental Investigation Of Aeration Self Mixing By Using Pulsating And Continuous Air Flow, Ahmed Ali Alkhafaji

Theses and Dissertations

Wastewater treatment is considered one of the most common forms of pollution control in the united states. Considered as an integral part of the wastewater treatment, the aeration process is the most energy-consuming process among all the processes that take place in any wastewater treatment plant. According to the United States Environmental Protection Agency (EPA), a wastewater treatment plant is expected to remove at least 85% of the suspended solids and dissolved organic compounds from the wastewater before discharging it to a river or a lake. The normal operation of the aeration process is by compressing air continuously to basin …

The Optimization Of Efficiency And Infrastructure For Modern Potable Water Treatment Plants, Brent A. Dekock

Theses and Dissertations

The USDOE Industrial Assessment Centers (IACs) is a program that is designed to help small and medium-sized manufacturing facilities reduce their overall costs and improve energy efficiency. This includes improving potable water treatment plants which supply water throughout the country. This thesis covers the process of how IAC branches and water treatment facilities generally operate, as well as several assessment recommendations that have been developed by a branch of the IAC for several water treatment plants based in the Rio Grande Valley of Texas. The steps of the assessment and water treatment process are described, and several cost saving measures …

Application Of Survival Analysis Techniques To Probabilistic Assessment Of Fatigue In Steel Bridges, Azam Nabizadehdarabi

Theses and Dissertations

The fatigue of engineering materials under repetitive loading is a significant issue affecting the design and durability of components and systems in a variety of engineering-related applications including civil, mechanical, aerospace, automotive, and electronics. Many factors can affect the service life of a component or system under repetitive loading, such as the type of structure, loading, connection details, stress state, peak stress or stress range, surface condition, temperature, and environmental exposure. Currently, there is no comprehensive probabilistic approach that can systematically address all the factors that contribute to fatigue on a single mathematical platform. However, advanced analysis techniques developed for …

An Advanced Approach For Contract Time Determination In Highway Projects, Cuauhtemoc Torres Cantu

Theses and Dissertations

In project management, finishing a project on schedule is one of the most important aspects. The Texas Department of Transportation (TxDOT) has been experiencing delays in some projects that can be accounted to an inaccurate project time estimation process. This research presents the development of a user-friendly and comprehensive computer-based contract time determination system. The enhanced system implements probabilistic scheduling techniques such as Program Evaluation and Review Technique, and Monte Carlo Simulation. Additionally, the application of a lognormal two-point PERT method is explored in this study. The new system proposes the use of a database of production rates based on …

Assessment Of Some Of The Common Practices Used In Scheduling Highway Projects, Jennifer Reyes

Theses and Dissertations

There are several factors documented in the literature that can affect the accuracy of estimated project durations in highway construction, such as weather, location, and soil conditions. Recently, the Texas Department of Transportation (TxDOT) raised a concern regarding some of the practices used when estimating the contract time for projects. This research presents an assessment of the effect that two practices identified have on the estimated project duration. These two practices include: 1) the estimated lead/lag times in project schedules and 2) scheduling with only critical or controlling activities. The effect of these practices is measured, primarily, by using four …

Structural Health Monitoring Of Laminate Structures Using Shear-Mode Piezoelectric Sensors, Hussain Altammar

Theses and Dissertations

Structural health monitoring (SHM) employing embedded piezoelectric transducers has shown potential as a promising solution for inspection of different engineering structures such as aircraft, bridges, and renewable energy structures. Despite advancements in the field of ultrasonic SHM, inspection of laminate structures is still a major challenge due to their susceptibility to various joint defects. This thesis presents a novel approach to tackle the challenge of inspecting laminate structures using shear-mode (d35) piezoelectric transducers that are made of lead zirconate titanate (PZT).

This study begins with the characterization of d35 piezoelectric transducers using analytical, numerical, and experimental approaches. The results were …

Discrete Element Analysis Of Scb Variability: Asphalt Mixtures, David Saul Renteria

Theses and Dissertations

The Semi-Circular Bending (SCB) test was modeled using the Discrete Element Method (DEM) implemented in numerical software Particle Flow Code (PFC). The fracture analysis of the SCB was studied using two mixtures gradation, Superpave and Coarse Matrix High Binder. The aggregate phase in the model was achieved by using two-dimensional aggregate images with different angularity indexes. The study of the variability of the SCB extends to the random generation of aggregate particles and air voids in the model, in addition to changing the properties at the interface between the aggregate and mastic phases. Results indicate the strong influence of the …

Modeling Atypical Building Use With Commercially Available Building Simulation Software, Sarah E. Schanck

Theses and Dissertations

National Guard armories are audited to provide recommendations for future energy reduction measures. The annual energy consumption of a New Jersey National Guard Armories cannot be modeled directly with commercially available building simulation software, due to discrepancies between the modeling capabilities of the software and the reality of the armory. A building simulation software, eQUEST, was chosen for use in this project. Discrepancies between eQUEST inputs and reality were identified and correction factors developed to minimize the effect of each discrepancy on predicted energy consumption, with the end goal of accuracy between predicted and actual energy consumption. In addition, an …

Computing Research In Academia: Classifications, Keywords, Perceptions, And Connections, Sung Han Kim

Theses and Dissertations

The Association for Computing Machinery (ACM) recognizes five computing disciplines: Computer Science (CS), Computer Engineering (CE), Information Technology (IT), Information Systems (IS), and Software Engineering (SE). Founded in 1947 the ACM is the world's largest society for computing educators, researchers, and professionals. While Computer Science has been a degree program since 1962, the other four are relatively new. This research focuses on understanding the graduate research in four of the five ACM disciplines (CS, CE, IT, and IS) using a large body of thesis and dissertation metadata. SE is not found in the metadata and graduate work in SE is …

Dynamic Moving Load Identification Using Optimal Sensor Placement And Model Reduction, Paul Augustine

Theses and Dissertations

A structure in service can be subjected to static, dynamic or moving loads. Several situations in practice involve estimation of moving loads which induce vibrations in the structure on which they are applied. An accurate estimation of these loads will ensure product quality and reliability of the final design, and mitigate the cost of structural health monitoring systems. The moving nature of dynamic loads increases the computational difficulty of the problem. One of the types of Inverse Problems involves estimation of the applied load from measured structural response such as strain or accelerations.

Measuring response at a limited number of …

Micro- And Macro-Scale Modeling Of Filter Aging: Effects Of Particle Poly-Dispersity And Fiber Cross-Sectional Shape, Ahmed M. Saleh

Theses and Dissertations

The goal of this study is to further advance the state of the art in developing self-sufficient methods to predict the performance of an aerosol filter. The simulation methods developed in this study are based on first principles and consequently, they do not rely on empirical correction factors. These simulation methods can be used to predict the instantaneous collection efficiency and pressure drop of a filter under dust-loading conditions. In the current study, 3-D micro- and macroscale CFD models are developed to simulate the service life of flat-sheet and pleated filters. These CFD micro- and macroscale models are also used …

Damage Detection Of Mixed-Mode Cracks In Large Truss Structures Using Wavelet Transform, Hussain Altammar

Theses and Dissertations

The use of dynamic response in damage identification has been gaining considerable attention over the last two decades. The aim of these methods is to detect the presence of a defect or a crack in components or structures. This study focuses on using modal properties for the damage detection of mixed-mode cracks in truss structures. The behavior of a mixed-mode crack is simulated by developing a macroscopic model that is integrated with the finite element model of a truss structure. The modal properties obtained from the model of the damaged structure are found to be comparable to the results of …

Aqueous Turbulence Structure Immediately Adjacent To The Air - Water Interface And Interfacial Gas Exchange, Binbin Wang

Theses and Dissertations

Air-sea interaction and the interfacial exchange of gas across the air-water interface are of great importance in coupled atmospheric-oceanic environmental systems. Aqueous turbulence structure immediately adjacent to the air-water interface is the combined result of wind, surface waves, currents and other environmental forces and plays a key role in energy budgets, gas fluxes and hence the global climate system. However, the quantification of turbulence structure sufficiently close to the air-water interface is extremely difficult. The physical relationship between interfacial gas exchange and near surface turbulence remains insufficiently investigated. This dissertation aims to measure turbulence in situ in a complex environmental …

A Comparative Analysis Of Energy Modelingmethods For Commercial Buildings, Spencer Mark Salmon

Theses and Dissertations

This thesis researched the accuracy of measured energy data in comparison to estimated hand calculation data and estimated building energy performance simulation data. In the facility management industry, there is minimal evidence that building energy performance software is being used as a benchmark against measured energy usage within a building. Research was conducted to find examples of measured energy data compared to simulated data. The study examined the accuracy of a simulation software and hand calculations to measured energy data. Data suggests that comparisons may be made between building energy performance simulated data and measured data, though comparisons are solely …

Starch Resin Moisture Level Effect On Injection Molding Processability And Molded Part Mechanical Properties With Pure Starch Resin And Polymer Blends, Jordan M. Ellingson

Theses and Dissertations

The current and forecasted global consumption of plastic packaging and products through the 21st century combined with the already reported and growing negative impact of plastics on the environment due to plastics being synthesized from nonrenewable resources that do not biodegrade is of serious concern. However, recent advances in starch technology including the development of thermoplastic starch (TPS) materials —polymers that are both renewable and biodegradable—have brought hope to reducing this impact. The mechanical properties of thermoplastic starch have often been improved by blending with synthetic polymers. One issue that arises with blending is volatilization of the melt from moisture …

Location-Allocation Optimization Of Supply Chain Distribution Networks: A Case Study, Mark Nicholas Helberg

Theses and Dissertations

The location of distribution centers is an important strategic decision in supply chain design, particularly as it relates to service quality, productivity, and profitability of the firm. There has been extensive research performed on distribution location models which require the use of complex algorithms and assumptions that make use of these models difficult in practice for small and medium enterprises (SMEs) that have limited capital and resources. Studies have also failed to capture and quantify potential business results of using more sophisticated methods. In this study, a deterministic and static location-allocation model is designed using a prototype software tool. The …

Best Practices Using Building Information Modeling In Commercial Construction, Simon Beveridge

Theses and Dissertations

There has been an increase in adoption of building information modeling (BIM) by commercial contractors over the past few years but there is not a clear indication of current application or the frequency of each use. This research was undertaken to determine the frequency and best practices of using BIM in commercial construction. Leading commercial contracting firms were contacted and employees were selected to complete a telephone survey that was designed to determine how they are using BIM. It was found that BIM is being used with more frequency on projects, with plans to continue to implement it even further …

A Comparative Study Of Strength And Stiffness Of Thin-Walled Specimens Fabricated By Fdm And 3d Printing Technologies, Miranda Rodrigo

Theses and Dissertations

Rapid Prototyped part failure constitutes a major issue for both RP providers and customers. When parts fail the reputation of the vendor is heavily deteriorated, customer dissatisfaction increase and replacement of the broken parts is often necessary to avoid the loss of future business. Product design teams often run into situations where Rapid Prototyped parts are not able to withstand shipping and handling and delivered broken or while demonstrating and examining the parts. When done in the face of customers this builds a perception of poor quality and lack of aptitude on the design group as well as the RP …

A Study Of The Cause Of Failure Of Rotationally Molded, High-Density Polyethylene, Sodium Hypochlorite Storage Tanks, Dixon Harold Abell

Theses and Dissertations

The topic of chemical oxidative degradation in rotational molded polyethylene (high-density cross-linked) chemical (sodium hypochlorite) storage tanks is an industry problem that ranks at the top of current business issues for manufacturers of chemical storage tanks. The degradation of these tanks not only compromises the physical and mechanical properties of the tank material, but reduces the life expectancy of the tank, eventually resulting in catastrophic tank failure. Premature tank failure comes at a hefty cost. The reputation of the manufacturer is questioned often resulting in immediate loss of customer satisfaction and future business. The leaking of the chemical from the …

An Experimental Investigation Of Friction Bit Joining In Az31 Magnesium And Advanced High-Strength Automotive Sheet Steel, Rebecca Gardner

Theses and Dissertations

Friction Bit Joining (FBJ) is a recently developed spot joining technology capable of joining dissimilar metals. A consumable bit cuts through the upper layer of metal to be joined, then friction welds to the lower layer. The bit then snaps off, leaving a flange. This research focuses on FBJ using DP980 or DP590 steel as the lower layer, AZ31 magnesium alloy as the top layer, and 4140 or 4130 steel as the bit material. In order to determine optimal settings for the magnesium/steel joints, experimentation was performed using a purpose-built computer controlled welding machine, varying factors such as rotational speeds, …

Natural Fibers And Fiberglass: A Technical And Economic Comparison, Justin Andrew Zsiros

Theses and Dissertations

Natural fibers have received attention in recent years because of their minimal environmental impact, reasonably good properties, and low cost. There is a wide variety of natural fibers suitable for composite applications, the most common of which is flax. Flax has advantages in tensile strength, light weight, and low cost over other natural fibers. As with other natural and synthetic fibers, flax is used to reinforce both thermoset and thermoplastic matrices. When flax is used in thermoplastic matrices, polypropylene and polyethylene are the main resins used. Although at first glance flax may seem to be a cheaper alternative to fiberglass, …

Investigation Of Rf Curing Parameters In Resin Infusion Molding, Christopher K. Love

Theses and Dissertations

The purpose of this study is to investigate RF or Radio Frequency energy as a viable alternative to traditional heating methods for the purpose of curing resins used in resin infusion molding, a molding system for polymeric composites. Traditional heating/curing methods include technologies such as room temperature, oven, microwave, infrared, and ultraviolet. Although RF curing provides far more advantages than disadvantages, its implementation into a manufacturing process can be challenging. Specifically, three critical elements must be present in order for RF to function in a manner that is profitable to the manufacturer. Those elements are: (1) the proper generator (voltage …

Development Of A Particle Flow Test For Rotational Molding, Russell B. Whatcott

Theses and Dissertations

One of the current testing method (the Dry Flow test) to qualify resin for use in production in the rotomolding process has been shown to have many flaws in both equipment and procedure. Research was done here to investigate a possible alternative that could eliminate some of these testing deficiencies. By reducing equipment and operator errors, the testing of materials becomes more valuable of an exercise. The Angular Flow test developed in this research can increase repeatability. By coming to understand the rotational molding process better, an evaluation that can give more valid information was devised.

Comparing The Feasibility Of Cutting Thin-Walled Sections From Five Commonly Used Metals Utilizing Wire Electric Discharge Machining, Richard C. Stephenson

Theses and Dissertations

Wire Electric Discharge Machining (wire-EDM) is a non-traditional machining process. Controlled electric sparks are successively used to vaporize part of a workpiece along a programmed path in order to machine a desired part. Because there is no tool that comes in direct contact with the workpiece, it is possible to machine thin, delicate parts. This thesis was designed to observe and analyze the differences in cutting capabilities for a conventional wire-EDM machine when cutting thin-walled sections from five commonly used metals utilizing a variation of roughing and finishing passes. The five metals that were used in this study are: Aluminum …

Friction Stir Welding Of High-Strength Automotive Steel, Eric Michael Olsen

Theses and Dissertations

The following thesis is a study on the ability to create acceptable welds in thin-plate, ultra-high-strength steels (UHSS) by way of friction stir welding (FSW). Steels are welded together to create tailor-welded blanks (TWB) for use in the automotive industry. Dual Phase (DP) 590, 780, and 980 steel as well as Transformation-Induced Plasticity (TRIP) 590 steel with thicknesses ranging from 1.2 mm to 1.8 mm were welded using friction stir welding under a variety of processing conditions, including experiments with dissimilar thicknesses. Samples were tested under tensile loads for initial determination if an acceptable weld had been created. Acceptable welds …