Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- BLDS (3)
- Composite (3)
- Aerodynamics (2)
- Boundary layer (2)
- CubeSat (2)
-
- Delamination (2)
- Heat Transfer (2)
- Reaction Wheel (2)
- Spacecraft (2)
- ADCS (1)
- AMELIA (1)
- Actuator Disk Theory (1)
- Adaptive Control (1)
- Aerospace (1)
- Aerospace engineering (1)
- Air augmented rocket engine induced turbulence (1)
- Attitude Control (1)
- BLDC motor (1)
- Backlash (1)
- Bamboo (1)
- Biocomposites (1)
- Bottle (1)
- Boundary layer transition (1)
- Buckling (1)
- C++ (1)
- CFD (1)
- CMG (1)
- Calibration (1)
- Carbon (1)
- Carbon fiber (1)
Articles 31 - 35 of 35
Full-Text Articles in Mechanical Engineering
Implementation Of A Conrad Probe On A Boundary Layer Measurement System, Charles Rocky Ulk
Implementation Of A Conrad Probe On A Boundary Layer Measurement System, Charles Rocky Ulk
Master's Theses
This thesis presents the design, calibration, and performance evaluation of a type of two-hole pressure probe anemometer known as a Conrad probe, as well as its subsequent implementation on an autonomous, compact boundary layer measurement device and its first application for subsonic in-flight measurements of a swept wing boundary layer. Calibration of the Conrad probe was accomplished using two calibration functions and a non-nulling method for resolving in-plane flow velocity direction and magnitude over a range of ±30 degrees. This approach to calibration and application offered the advantages of rapid data acquisition with lower energy consumption than alternative methods for …
Adaptive Control Applied To The Cal Poly Spacecraft Attitude Dynamics Simulator, Matthew C. Downs
Adaptive Control Applied To The Cal Poly Spacecraft Attitude Dynamics Simulator, Matthew C. Downs
Master's Theses
The goal of this thesis is to use the Cal Poly Spacecraft Attitude Dynamics Simulator to provide proof of concept of two adaptive control theories developed by former Cal Poly students: Nonlinear Direct Model Reference Adaptive Control and Adaptive Output Feedback Control. The Spacecraft Attitude Dynamics Simulator is a student-built air bearing spacecraft simulator controlled by four reaction wheels in a pyramidal arrangement. Tests were performed to determine the effectiveness of the two adaptive control theories under nominal operating conditions, a “plug-and-play” spacecraft scenario, and under simulated actuator damage. Proof of concept of the adaptive control theories applied to attitude …
Rayleigh Flow Of Two-Phase Nitrous Oxide As A Hybrid Rocket Nozzle Coolant, Lauren May Nelson
Rayleigh Flow Of Two-Phase Nitrous Oxide As A Hybrid Rocket Nozzle Coolant, Lauren May Nelson
Master's Theses
The Mechanical Engineering Department at California Polytechnic State University in San Luis Obispo currently maintains a lab-scale hybrid rocket motor for which nitrous oxide is utilized as the oxidizer in the combustion system. Because of its availability, the same two-phase (gas and liquid) nitrous oxide that is used in the combustion system is also routed around the throat of the hybrid rocket’s converging-diverging nozzle as a coolant. While this coolant system has proven effective empirically in previous tests, the physics behind the flow of the two-phase mixture is largely unexplained. This thesis provides a method for predicting some of its …
An Experiment On Integrated Thermal Management Using Metallic Foam, Derek M. Geiger
An Experiment On Integrated Thermal Management Using Metallic Foam, Derek M. Geiger
Master's Theses
This report details an approach to using metal foam heat exchangers inside an integrated thermal management system on a variable cycle engine. The propulsion system of interest is a variable cycle engine with an auxiliary, variable flow rate fan. The feasibility of utilizing an open-celled metallic foam heat exchanger in the ducting between the constant and variable-fans on this variable cycle engine to cool the avionics was explored using an experimental approach. Two heat exchangers, 6.3 inch width by 6.3 inch length by 0.5 inch thickness, were constructed from 20 and 40 pores per inch (PPI) metal foam and tested. …
A System For Measuring The Lift And Drag Forces Of A Spinning Golf Ball Held Fixed Within A Wind Tunnel, Ryan R. Miller
A System For Measuring The Lift And Drag Forces Of A Spinning Golf Ball Held Fixed Within A Wind Tunnel, Ryan R. Miller
Master's Theses
A system was designed, built and tested in order to test the aerodynamic properties of a standard golf ball in a wind tunnel manufactured by ELD, Inc. model 406(B). The system consists of a rotating shaft, on which the golf ball is attached, connected to a two-axis force transducer. Additionally, an automated data acquisition system was built for enhanced precision of measurements. Data for wind speeds up to 160 ft/s and rotational speeds up to 8,600 rpm were obtained and analyzed. The purpose of the designed apparatus was to allow for studies to better understand the lift and drag coefficients …