Open Access. Powered by Scholars. Published by Universities.®

Mechanical Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Aerospace Engineering

Air Force Institute of Technology

Theses and Dissertations

Articles 31 - 41 of 41

Full-Text Articles in Mechanical Engineering

Optimization Of A Low Heat Load Turbine Nozzle Guide Vane, Jamie J. Johnson Mar 2006

Optimization Of A Low Heat Load Turbine Nozzle Guide Vane, Jamie J. Johnson

Theses and Dissertations

Often turbomachinery airfoils are designed with aerodynamic performance foremost in mind rather than component durability. However, future aircraft systems require ever increasing levels of gas-turbine inlet temperature causing the durability and reliability of turbine components to be an ever more important design concern. As a result, the need to provide improved heat transfer prediction and optimization methods presents itself. Here, an effort to design an airfoil with minimized heat load is reported. First, a Reynolds-Averaged Navier-Stokes (RANS) flow solver was validated over different flow regimes as well as varying boundary conditions against extensive data available in literature published by the …

Go to article

Alleviation Of Buffet-Induced Vibration Using Piezoelectric Actuators, Shawn D. Morganstern Mar 2006

Alleviation Of Buffet-Induced Vibration Using Piezoelectric Actuators, Shawn D. Morganstern

Theses and Dissertations

Buffet-induced vibration has been problematic for aircraft structures for many years. The F-16 ventral fin, while prone to these effects, lends itself well to the evaluation of modern active structural and flow control technologies. The objective of this research was to determine the most critical natural modes of vibration for the F-16 ventral fin and design piezoelectric actuators capable of reducing buffet-induced ventral fin vibration. A finite element model (FEM) for the fin was developed, tuned and optimized to closely match published modal frequencies. Piezoelectric actuator patches were designed using the strain characteristics of the FEM and integrated into the …

Go to article

Performance Measurements Of Direct Air Injection In A Cavity-Based Flameholder For A Supersonic Combustor, Scott G. Edens Dec 2005

Performance Measurements Of Direct Air Injection In A Cavity-Based Flameholder For A Supersonic Combustor, Scott G. Edens

Theses and Dissertations

For several years the Air Force Research Lab Propulsion Directorate has been studying the difficulties in fueling supersonic combustion ramjet engines with hydrocarbon based fuels. Recent investigations have focused on the use of direct air injection into a directly-fueled cavity-based flameholder. Direct air injection has been shown qualitatively to be a valuable tool for improving cavity combustion. Little quantitative data is available that characterizes the performance of cavity-based flameholders. The objective of this research was to quantitatively determine the specific advantages and disadvantages of the direct air injection scheme. This was accomplished via intrusive probing into a supersonic free stream …

Go to article

Heat Transfer To The Inclined Trailing Wall Of An Open Cavity, Orval A. Powell Mar 1999

Heat Transfer To The Inclined Trailing Wall Of An Open Cavity, Orval A. Powell

Theses and Dissertations

Experimental and computational heat transfer investigations were performed on a cavity with an inclined trailing wall (20-degrees to the horizontal), simulating one under investigation for use in a scramjet engine. Heat transfer data are reported in the form of Stanton number obtained using a curve fit to the recorded transient surface temperature history under cold flow conditions. Ascending from the reattachment point, the Stanton number increased by nearly 50% due to flow compression. This effect of flow compression was also evident at the junction of the cavity floor and inclined trailing wall, where the Stanton number also increased by 50%. …

Go to article

Electro-Mechanical Fatigue Behavior Of A Quasi-Isotropic Laminate With An Embedded Piezoelectric Actuator, Tse Lin Hsu Sep 1998

Electro-Mechanical Fatigue Behavior Of A Quasi-Isotropic Laminate With An Embedded Piezoelectric Actuator, Tse Lin Hsu

Theses and Dissertations

This study primarily investigated the electro-mechanical fatigue behavior of the embedded piezoelectric actuators in graphite/epoxy laminate with a lay-up of 0 | ± 45 | 90s. A secondary focus was the investigation of the mechanical fatigue effects of the 0 | 0 | ± 45 | 0 | 0 | 90s laminate with embedded PZT under tensile loading. All the fatigue tests were conducted with a triangular loading waveform which had a frequency of 10 Hz and with R=0. 1. In the electro-mechanical testing, the embedded actuator was excited by a -10 V to -100 V or a 10 V …

Go to article

Effects Of Liquid Transpiration Cooling On Heat Transfer To The Diverging Region Of A Porous-Walled Nozzle, Daniel J. Schieb Dec 1997

Effects Of Liquid Transpiration Cooling On Heat Transfer To The Diverging Region Of A Porous-Walled Nozzle, Daniel J. Schieb

Theses and Dissertations

This research effort investigated the effects of evaporation of water on the heat transferred to the wall of the diverging portion of a porous walled nozzle The AFIT High Pressure Shock Tube was used with a two-dimensional Mach 3 nozzle. One flat surface of the nozzle was fitted with a layer of porous stainless steel from the nozzle throat to the exit. This porous material was saturated with water to simulate liquid transpiration cooling. Surface temperature data was taken in this region using fast response coaxial thermocouple. Heat transfer was determined from the surface temperature history. Data was taken for …

Go to article

Numerical Analysis Of Two And Three Dimensional Recessed Flame Holders For Scramjet Applications, Douglas L. Davis Sep 1996

Numerical Analysis Of Two And Three Dimensional Recessed Flame Holders For Scramjet Applications, Douglas L. Davis

Theses and Dissertations

This study investigated the flame holding properties of recessed cavities in supersonic flow using numerical analysis techniques. A simplified analytical model indicated that an important property for flame holding was the lower residence time. Several chemical kinetic rate models for hydrogen and hydrocarbon combustion were compared. The perfectly stirred reactor model also indicated that trace species diffusion should increase flame spreading rate, and that heat loss reduces flame holding limits. After nonreacting calibration, two-dimensional simulations confirmed the perfectly stirred reactor results for blowout limits. Also, the effect of trace species diffusion on flame spreading was shown to be negligible, and …

Go to article

An Investigation Of The Characteristics Of Regenerative Heat Exchangers, Timothy J. Murphy Jun 1996

An Investigation Of The Characteristics Of Regenerative Heat Exchangers, Timothy J. Murphy

Theses and Dissertations

The objective of the current research was to investigate the effects of reducing screen thickness on the volume and compactness factor of stacked, wire-screen regenerators. An improved transient step-change method was devised which integrated experimental data with a numerical model of the flow to determine the heat transfer coefficient and friction factor. The improvements to the approach are: (1) the measured inlet temperature trace is used, (2) the heat transfer coefficient is based on a parameter called the sponge effect delay time, and (3) the important effect of the tube surrounding the matrix is included in the numerical model. The …

Go to article

Effects Of Blowing Ratios On Heat Transfer To The Throat Region Of A Porous-Walled Nozzle, Fu-Jung Chen Jun 1995

Effects Of Blowing Ratios On Heat Transfer To The Throat Region Of A Porous-Walled Nozzle, Fu-Jung Chen

Theses and Dissertations

The effects of transpiration cooling on heat transfer in the throat region of a porous-walled nozzle were investigated. The experiments were performed in the AFIT low speed shock tube fitted with a Mach 2 nozzle. A blowing region was limited to the area from 1.3 cm prior to the throat to 1.2 cm downstream of the throat. The blowing ratios from -0.0002 (suction) to 0.0117 (blowing) of the main stream flow were studied. Heat flux data were taken from both sides of the nozzle. One side was transpiration cooled by secondary air injection through a porous wall, while the other …

Go to article

Effects Of Blowing Ratio On Heat Transfer To The Throat Region Of A Porous-Walled Nozzle, Joseph L. Lenertz Dec 1994

Effects Of Blowing Ratio On Heat Transfer To The Throat Region Of A Porous-Walled Nozzle, Joseph L. Lenertz

Theses and Dissertations

This experiment analyzed the effects of blowing ratio on heat transfer to the throat region of a porous-walled nozzle, using the AFIT low speed shock tube. Heat flux data were taken from both sides of a two-dimensional Mach 2.0 Re-m=5.2x107 nozzle using thin film resistance thermometers. One side was transpiration-cooled by secondary air injection through a sintered wall, while the other side served as a control. Control results were validated using empirical relations, and cooled side results showed up to a 14% reduction in heat transfer coefficient at blowing ratios of only 0.51%. The linear nature of cooling effectiveness …

Go to article

Solution To Eigenvalue Problems Of Antisymmetric Cross-Ply And Antisymmetric Angle-Ply Laminated Plates Using Affine Transformations, Zaffir A. Chaudry Dec 1984

Solution To Eigenvalue Problems Of Antisymmetric Cross-Ply And Antisymmetric Angle-Ply Laminated Plates Using Affine Transformations, Zaffir A. Chaudry

Theses and Dissertations

Using affine transformations and suitably recasting the buckling vibration differential equations, the eigenvalue problem of anti-symmetric cross-ply and antisymmetric angle-ply laminated rectangular plates has been reduced to a function of two strong material constants, the generalized rigidity ratio, whose range is in the closed interval from 0 to 1, and the ratio of principal lamina stiffness. With the reduction in number of constants an exhaustive parameter study of buckling and vibration solution trends, is possible. The buckling coefficients decrease with decreasing value of generalized rigidity ratio for both antisymmetric cross-ply and antisymmetric angle-ply laminates. For a given aspect ratio, and …

Go to article

First Prev