Structural Materials Commons^™

Analysis Of Loading Rate, Fiber Orientation And Material Composition Through Image Processing And Digital Volume Correlation In High Performance Concrete, Aidan R. Carlson

Electronic Theses and Dissertations

Ultra High Performance Concrete (UHPC) and High Performance concrete (HPC) is characterized by high compressive strength and high toughness. This is achieved through maximizing the particle packing density in the matrix and the use of fibers to reinforce the matrix, increasing the materials toughness. The interactions of fibers and the matrix during loading is quite complex and involves several different energy dissipation mechanisms. The goal of this work and this thesis is to investigate these interactions and identify any changes in material response, and hope that these changes may be useful for the design of UHPC moving forward.

In this …

Modular Composite Sandwich Structures For Thermal And Structural Retrofitting Of Existing Buildings, Marc Al Ghazal

Masters Theses

Around 40% of global energy consumption and 30% of worldwide carbon dioxide (CO2) emissions are attributed to buildings. Most of this consumption is dedicated to ensuring thermal comfort. The goal of this research was to develop and field validate retrofit solutions to improve the energy efficiency of buildings. Exterior cladding panels were designed and tested to ensure adequate thermal and structural performance. Sandwich panels (glass fibers reinforced polymer (GFRP) skins and polymeric foam cores) were fabricated using the vacuum assisted resin transfer molding (VARTM) process. Extruded polystyrene (XPS) and polyurethane (PU) foams were compared as core materials through a series …

Experimental Characterization And Computer Vision-Assisted Detection Of Pitting Corrosion On Stainless Steel Structural Members, Riley J. Muehler

Master's Theses

Pitting corrosion is a prevalent form of corrosive damage that can weaken, damage, and initiate failure in corrosion-resistant metallic materials. For instance, 304 stainless steel is commonly utilized in various structures (e.g., miter gates, heat exchangers, and storage tanks), but is prone to failure through pitting corrosion and stress corrosion cracking under mechanical loading, regardless of its high corrosion resistance. In this study, to better understand the pitting corrosion damage development, controlled corrosion experiments were conducted to generate pits on 304 stainless steel specimens with and without mechanical loading. The pit development over time was characterized using a high-resolution laser …

Efficient Sintering Of Lunar Soil Using Concentrated Sunlight, Diprajit Biswas

Electronic Theses and Dissertations

Construction material is one crucial need for long-term habitation on the moon. When concentrated for high heat flux, solar radiation can heat lunar soil or regolith until it sinters at temperatures above 900°C. The solid, sintered soil simulant can be used as construction material. This work explores the conditions leading to effective lunar soil sintering for both direct and indirect irradiated sintering. Lunar soil simulants were sintered using concentrated light from a xenon-arc lamp with varying heat flux intensity. During direct sintering of LHS-1, a sintering range of 860°C-1140°C corresponding to a peak heat flux of 105-120 kW/m2 was identified …

Mechanics And Mechanisms Of Fracture For An Eastern Spruce Subject To Transverse Loading Using Acoustic Emission, Parinaz Belalpour Dastjerdi

Electronic Theses and Dissertations

Due to its excellent structural qualities and accessibility, wood is among the most often utilized structural materials. Despite its ubiquity, wood poses numerous challenges. It is heterogeneous and anisotropic. It has a complex hierarchical ultrastructure, and the properties can have wide variation within a species, and indeed within an individual tree. This work aims to improve our understanding of the strength and fracture behavior of spruce-pine-fir (south) (SPFs), particularly in cross-grain direction. This study’s primary goal is to examine the relationship between crack propagation and cross grain morphology under the following loading configurations: compact tension, compression, and rolling shear. The …

Machine Learning-Based Data And Model Driven Bayesian Uncertanity Quantification Of Inverse Problems For Suspended Non-Structural System, Zhiyuan Qin

All Dissertations

Inverse problems involve extracting the internal structure of a physical system from noisy measurement data. In many fields, the Bayesian inference is used to address the ill-conditioned nature of the inverse problem by incorporating prior information through an initial distribution. In the nonparametric Bayesian framework, surrogate models such as Gaussian Processes or Deep Neural Networks are used as flexible and effective probabilistic modeling tools to overcome the high-dimensional curse and reduce computational costs. In practical systems and computer models, uncertainties can be addressed through parameter calibration, sensitivity analysis, and uncertainty quantification, leading to improved reliability and robustness of decision and …

Correlation Between Laboratory Testing Results And In-Situ Sidewalk Scaling, Brian R. Shea

Masters Theses

Scaling tests aim to induce scaling behavior in concrete specimens similar to environmental conditions. The efficacy of laboratory tests’ ability to match environmental conditions is important to be able to evaluate the durability of concrete exposed to freeze-thaw cycles and de-icers. This study attempts to correlate results between two existing scaling test standards, ASTM C672 and the BNQ NQ 2621-900. The correlation is done via scaling evaluation including computer-based photogrammetric analysis, visual ratings, and cumulative mass loss measurements. Then a correlation between the laboratory testing and in-situ sidewalk panel specimens is made via visual ratings.

Reduction Of Embodied Carbon In Buildings Through Use Of Low Carbon Strategies And Standardization And Enforcement Of Life Cycle Assessment, Bhargavi Sai Sudhakar

Master's Projects and Capstones

The building and construction industry is energy intensive and as of 2021, this industry is responsible for 37% of the total global greenhouse gas emissions. In previous studies of conventional buildings, the operational energy of a building contributed to 80% and the embodied energy contributed to 20% of the total life cycle energy. With increase in policies and standards that focus on reducing the operational energy, low energy and certified green buildings have emerged where the operational energy has considerably reduced. The relative and absolute share of embodied energy in these energy efficient buildings have increased due to excessive use …

A Study On Early Age Properties Of Concrete For Precast And 3d Printing, Debalina Ghosh

Doctoral Dissertations

Concrete is the second-most consumed material, leading the global Portland cement production of 4.1 billion tons in 2020 and 5-8% of global Carbon dioxide (CO₂) emission annually. As with any other material and practice, the construction industry is also ever-changing to meet market demand, evolving technology, and resource limitation. In the case of concrete construction, one of the main concerns is the lack of automation. In the last few decades, some new construction methods have risen to address this concern. Some of these economic and successful practices are precast construction, self-compacting concrete (SCC), and 3D printing of concrete(3DPC). …

Crack Control And Bond Performance Of Alternative Coated Reinforcements In Concrete, Sachin Sreedhara

All Dissertations

Concrete cracking in structures is a ubiquitous problem which can lead to the deterioration of the structure. Other than affecting the strength aspect of a structure, cracking impacts the serviceability criteria as well. Although cracking phenomenon in any structure is highly inevitable, it has to be minimized in order to maintain a structure’s life effectively. Cracking in reinforced concrete structures is related to the bond strength developed between the bar and the concrete. It also depends on an ability of the bar to resist the stresses due to shrinkage to minimize the crack. Another important aspect is the resistance offered …

Hydration Kinetics, Microstructure, And Mechanical Strength Development Of Cement-Based Composites Incorporating Phase Change Materials, Afshin Marani

Electronic Thesis and Dissertation Repository

The research conducted in this thesis investigates the effects of phase change materials (PCMs) on the hydration kinetics and strength development of cement-based composites using extensive experimental and numerical analyses. Purposefully, the effect of microencapsulated PCMs (MPCMs) on the strength development of cement-based mortars and concretes was evaluated using powerful machine learning models trained with the largest available experimental data. Furthermore, a novel ternary machine learning approach was proposed to optimize the mixture design of mortars and concretes based on the thermos-physical properties of the MPCMs. The results obtained from machine learning simulations suggest the assessment of the effects of …

Dynamic Response Of Elastic Two-Story Steel Moment Frame Scaled Structure Equipped With Viscous Dampers, Garrett L. Barker, Alexander L. Poirier

Architectural Engineering

The authors of this report are Architectural Engineering undergraduate students at California Polytechnic State University, San Luis Obispo. Damping is a complex, experimentally derived value that is affected by many structural properties and has a profound effect on the dynamic response of structures. Deducing the inherent damping of a steel moment frame and affecting the damping ratio with viscous dampers are two topics explored in this paper. Dampers are commonly implemented in resilient structures that perform better in a design basis earthquake, reducing the seismic cost and downtime. Undergraduate coursework does not delve into the factors that affect damping and …

Non-Destructive Evaluation Of Concrete Using Electrical Resistivity And Ultrasonic Wave Propagation, Justin Harris

Electronic Theses and Dissertations

With the intent to investigate the relationship between concrete physical properties and non-destructive evaluation techniques (NDE), several experiments were performed. Specimens were made at varying geometries using a range of different concrete mixes under several different curing conditions. These specimens were subjected to a combination of electrical resistivity and ultrasonic wave propagation measurements. One part of this study investigated determining the orientation of steel fibers using electrical resistivity. This resulted in the fabrication of a four-probe square device with the potential capabilities of determining fiber orientation. The other part of this research applied ultrasonic wave propagation via through-transmission along with …

Evaluating The Effects Of Curing Methods On Bcsa Cement Concrete, Hannah Allen

Civil Engineering Undergraduate Honors Theses

BCSA cement is a type of cement that makes concrete set up much quicker than typical portland cement concrete. BCSA cement concrete also has a much higher compressive strength than that of portland cement concrete. This study was conducted to determine the effect of different curing conditions on the compressive strength of BCSA cement concrete.

Effects Of Bonding Pressure And Lamina Thickness On Mechanical Properties Of Clt Composed Of Southern Yellow Pine, Cody S. Bates

Theses and Dissertations

This study produced cross-laminated timber panels at a range of four lamina thickness (5/8, 1, 1 1/8, and 1 1/4 inch) and three bonding pressures (50, 125, 200 psi), producing a total of 12 panels for mechanical testing. The goal of this study is to observe how the thickness and pressure trends affect the mechanical properties of CLT. Tests include flatwise bending, flatwise shear, internal-bond, and delamination. Results showed that bending MOE decreases as the panel thickness increases while bonding pressure had no significance. Bending MOR was less significant for the thickness and more significant for pressure compared to the …

Shear Strength Of Concrete Beams Made With Belitic Calcium Sulfoaluminate Cement, Caleb W. Chesnut

Graduate Theses and Dissertations

The need for a cleaner alternative to portland cement (PC) concrete has led to increasing interest in alternatives to PC. Structural properties of most of these alternative cements are still an open research topic. One promising alternative cement is belitic calcium sulfoaluminate (BCSA) cement. The study presented in this paper investigated the shear strength, long term compressive strength, and carbonation in BCSA cement and PC concrete beams. A total of twelve eight-foot long beams were made; eight BCSA cement concrete beams and four PC concrete beams to be tested at various ages depending on cement type. Two beams of each …

Development Of Lambda Factors For Masonry Design With Lightweight Grout, Rumi Shrestha

All Theses

Reduction in structural mass, improvement in thermal performance, and reduction in shrinkage cracking through internal curing are some of the reasons that lightweight (LW) aggregates have been used in structures and pavements for decades. However, lightweight grout is still not permitted for use in reinforced masonry construction by the TMS 402/602-16 code. In order to realize the benefits of lightweight grout in U.S. reinforced masonry construction, a codified procedure for its use is required which must be informed by experimental testing.

This research is a pilot project directed to characterize the performance of LW grout in comparison to normal weight …

Frequency Effect On Peak Pressure Coefficients Using The Narrowband Synthesis Random Flow Generator (Nsrfg) Method, Zayuris Del Carmen Atencio Mojica

Graduate Theses and Dissertations

The collapse of the Tacoma Narrows Bridge in Washington state in 1940 due to high wind forces gave structural engineers notice of the importance of understanding the behavior of wind forces on infrastructure. Wind forces play an important role in the design of buildings and other structures. ASCE 7-16 is the manual used for the design of these buildings and other structures throughout the country. These design criteria have been approved based on research projects involving experimental procedures. For the design of wind loads, ASCE 7-16 uses criteria based on wind tunnel (WT) tests. However, since the development of computing …

Material Property Heterogeneity In Dimensional Lumber And Its Relationship To Mass Timber Performance, Fiona O'Donnell

Doctoral Dissertations

According to the Environmental Protection Agency, buildings account for 38% of the United States' carbon dioxide emissions, providing architects and structural engineers a unique opportunity to mitigate a significant factor driving climate change by implementing innovative and sustainable technology in infrastructure design. Wood and mass timber products are becoming an increasingly popular alternative building material due to their economic and environmental benefits. The natural growth of wood leads to highly heterogeneous material properties. Defects such as checks, knots, and localized slope of grain contribute to some of this variation; however, wood properties vary significantly even in clear wood. Using mass …

Harnessing The Mechanics Of Thin-Walled Metallic Structures: From Plate-Lattice Materials To Cold-Formed Steel Shear Walls, Fani Derveni

Doctoral Dissertations

Thin-walled structures have received a lot of interest during the last years due to their light weight, cost efficiency, and ease in fabrication and transportation, along with their high strength and stiffness. This dissertation focuses on the mechanical performance of thin-walled metallic structures from cold-formed steel shear walls and connections (PART I) to plate-lattice architected materials (PART II) via computational, experimental, and probabilistic methods. Cold-formed steel (CFS) shear walls subjected to seismic loads is the focus of PART I of this dissertation. An innovative three-dimensional shell finite element model of oriented strand board (OSB) sheathed CFS shear walls is introduced …

Microscopic And Image Processing Characterization Of Aggregates To Predict Asr Expansion Potential Of Concrete, Ammar Elfatih Abdelssamd Elhassan

Doctoral Dissertations

Preventing ASR occurrence in new concrete structures requires reliable and quick methods to identify reactive aggregates and to evaluate proper mitigation alternatives. The current accelerated mortar-bar expansion tests (ASTM C 1260 or ASTM C1567) and the concrete prism expansion test (ASTM C 1293) have been reported to have several limitations. Assessment of the extend of ASR damage in existing affected structures requires more understanding on how ASR expansion and damage develop in field conditions such as under confinements and under relatively slow rate of ASR reaction.

The significance of ASR expansion rate and bi-axial restrain on concrete degradation has been …

Development Of Hybrid Ultra-High Performance Concrete Thermoplastic Composite Panels For Blast And Ballistic Protection, Alyssa M. Libby

Electronic Theses and Dissertations

In recent years, ultra-high performance concrete (UHPC) has become a material of interest for structures needing resistance to impact and blast loadings. These types of loadings have induced brittle flexural failure in UHPC due to punching shear from the impactor. One way to improve the impact resistance, energy absorption, and ductility of UHPC is by adding fiber-reinforced polymer (FRP) skins to the front and rear faces of the concrete, resulting in a sandwich configuration. In this study, E-glass fiber-reinforced thermoplastic laminates were bonded to UHPC panels using a heated consolidation process known as stamp thermoforming. The bond between the UHPC …

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …

Balsa Wood Bridge, Andrew Harris

All Undergraduate Projects

Faculty at Central Washington University proposed a challenge to mechanical engineering students that could be accomplished in an in-home setting. The goal was to create a balsa wood bridge, weighing no more than 85 grams, that can support a load over an open span and raise above its resting position by means of a mechanical system. To produce a successful solution to the problem, a vertical lift bridge was created consisting of two lifting towers and a load bearing bridge. Using equations of static equilibrium and strength of materials, the required width for each member was determined. Project requirements were …

Timber Bridge Pile Splicing With Fiber Reinforced Polymer Wraps, Drew L. Damich

Graduate Theses, Dissertations, and Problem Reports

Timber pile repair using splicing is widely used but little research has been done to determine their strength capacity after repair using this method. Current timber pile splicing mechanisms utilize various steel or wooden components. Fiber Reinforced Polymer (FRP) wraps can be utilized as replacement to conventional materials in splicing of timber piles. This study evaluated the strength capacities of traditional splicing mechanisms in relation to FRP wrap splice mechanisms. Traditional splicing mechanisms consisted of flat steel plate, C-channel steel plate, and wooden plate splices. The FRP wrap splice consisted of unidirectional glass/epoxy composite with three layers of fabric as …

Laboratory Testing And Mechanistic Analysis Of Treated Subgrade Soils, Hari Kumar Reddy Yarrapureddi

Civil Engineering Theses

Calcium-based stabilizing agents such as cement and lime have been extensively used to improve the engineering properties of base and subgrade layers of pavement systems. Recently, polymers and chemical stabilizers have become popular due to cost efficiency, ease of application, and fast curing times. In this study, California Bearing Ratio (CBR) values of polymer and chemical treated soils were compared with the CBR values of soils treated with conventional stabilizers. Parametric sensitivity analyses was carried out on key parameters including the type of subgrade soil, stabilizing agent, stabilizing agent treatment levels, and moisture conditioning. Additionally, numerical analyses was performed to …

Analysis Of Burning Wood In The Transient State And The Application To Structural Design, Roberta Veliz, Kimberly Guzman

Architectural Engineering

Determining the extent of the contribution of exposed timber on compartment fire dynamics in open floor plans is a complex process. Designers traditionally used compartmentalization design methods which create spaces where flashover is likely, given the fuel load and ventilation conditions. However, due to the large geometric dimensions and spread of fuel, fires in open floor plans are more likely to remain as localized or traveling fires. As such, an understanding of not only ignition potential but also flame spread is critical to characterizing the contribution of exposed timber. An integral step in characterizing the potential contribution is through an …

Macro - And Microstructure Evaluation And Field Applications Of Concrete With Recycled Glass Pozzolan, Marija Krstic

Dissertations and Theses

Concrete is the most used material in the world, second only to water. Conventional concrete is produced with Portland cement (PC). The production of cement is an energy intensive operation that has raised significant environmental concerns, since one ton of cement generates an equal ton of CO₂. In the USA about 90 million tons of cement are used annually, with 3 million tons used in New York. Most contemporary concrete applications for buildings and infrastructure use high-performance concrete (HPC) mixtures which are produced by replacing a percentage of cement with supplementary cementitious materials (SCMs), consisting mainly of fly-ash …

Time-Dependent Reliability Framework For Durability Design Of Frp Composites, Rajneesh Kumar Bharil

Graduate Theses, Dissertations, and Problem Reports

The life-cycle performance, durability, and aging characteristics of Fiber Reinforced Polymer (FRP or Structural Composites) have been of keen interest to the engineers engaged in the FRP design, construction, and manufacturing. Unlike conventional construction materials such as steel and concrete, the design guidelines to account for the aging of FRP are somewhat scattered or not available in an approved or consistent format. Loss of strength over time or aging of any structural material should be of concern to engineers as the in-service lifespan of many engineering structures is expected to exceed 100 years. Use of durability strength-reduction factors or factors …

Retrofit Of Corroded Corrugated Metal Culverts Using Gfrp Slip-Liner, Rahulreddy Chennareddy

Civil Engineering ETDs

Culverts are water conveyance structures, typically used to allow water flow and maintain a balance between the flow streams without interrupting structures such as highways and bridges. Corrugated metal pipes (CMPs) have been used as culverts in North America since the 1950s because of their low cost and simple construction method. Today, the corrosion of CMPs is a major problem faced by all U.S. Departments of Transportation. There is an urgent need to provide an efficient solution, one that is corrosion-resistant, to retrofit thousands of corroded CMPs across the country. High specific strength, high strength to weight ratio, corrosion resistance, …