Polymer and Organic Materials Commons^™

Atomistic Simulations Of Defect Nucleation And Intralayer Fracture In Molybdenum Disulphide During Nanoindentation, James A. Stewart

Graduate Theses and Dissertations

Molybdenum disulphide (MoS2) is a layered, hexagonal crystal that has a very low coefficient of friction. Due to this low coefficient of friction, MoS2 has become a well-known solid lubricant and liquid lubricant additive. As such, nanoparticles of MoS2 have been proposed as an additive to traditional liquid lubricants to provide frictional properties that are sensitive to different temperature and pressure regimes. However, to properly design these MoS2 nanoparticles to be sensitive to different temperature and pressure regimes, it is necessary to understand the mechanical response of crystalline MoS2 under mechanical loading. Specifically, the fundamental mechanism associated with the nucleation …

Pretreatment And Pyrolysis Of Rayon-Based Precursor For Carbon Fibers, Kokouvi Akato

Masters Theses

In this work, two rayon fibers were investigated as carbon fiber precursors. A detailed consideration has been applied to a domestically produced cellulose fiber to carbon fiber (CF) transition. This transition of precursor to carbon fiber can be subdivided into two stages: pyrolysis (thermal decomposition) of cellulose in air and high temperature treatment in an inert atmosphere. The specific objectives were to investigate the stabilization stage of the produced rayon with respect to changes taking place during thermal decomposition, and to evaluate the effects on the properties of the carbonized fiber. Changes taking place during the conversion process of the …

Biaxial & Twist Testing Of Composite Carbon-Fiber Sandwich Panels For Automotive Racing Vehicles, Erik Eckberg

Materials Engineering

Composite sandwich panels were constructed with 4-ply plain weave carbon-fiber/epoxy face sheets in the 0^o/45^o/0^o/45^o orientation and 1/8^th inch Nomex honeycomb core. The panels were cut into 5-inch square test plates for mechanical testing. All testing was done on a fixture designed and fabricated by Pratt & Miller Engineering and installed on an Instron testing system at Cal Poly. The twist test was performed by supporting diagonal corners of the plate while simultaneously loading the opposite two corners at a crosshead rate of .06 in/min (ASTM 3044-94R11). Out of 10 panels tested, …

Blunt Impact Performance Evaluation Of Helmet Lining Systems For Military And Recreational Use, Jaclyn Siniora, Ryan Taylor, Darren Suey

Industrial Technology and Packaging

With the increasing problem in collegiate athletes experiencing injuries to the brain, different helmet liners where put to the test to see which liner provided athletes the greatest protection under specific conditions.

This senior project evaluates five different liners in football helmets. Each of the helmet liners were tested at three different temperatures: hot, cold, and ambient. Each helmet had seven different impact locations which were put to the test. The project was designed to be used to test ACH military combat liners as well. Due to shipping bottle necks the ACH combat liners have been left to future Cal …

Biomedical Properties And Preparation Of Iron Oxide-Dextran Nanostructures By Maple Technique, Carmen Steluta Ciobanu, Simona Liliana Iconaru, Eniko Gyorgy, Mihaela Radu, Marieta Costache, Anca Dinischiotu, Philippe Le Coustumer, Khalid Lafdi, Daniela Predoi

Chemical and Materials Engineering Faculty Publications

Background: In this work the chemical structure of dextran-iron oxide thin films was reported. The films were obtained by MAPLE technique from composite targets containing 10 wt. % dextran with 1 and 5 wt.% iron oxide nanoparticles (IONPs). The IONPs were synthesized by co-precipitation method. A KrF* excimer laser source (λ = 248 nm, τFWHM≅25 ns, ν = 10 Hz) was used for the growth of the hybrid, iron oxide NPs-dextran thin films.

Results: Dextran coated iron oxide nanoparticles thin films were indexed into the spinel cubic lattice with a lattice parameter of 8.36 Å. The particle sized calculated was …

Carbon Nanotubes Grown On Glass Fiber As A Strain Sensor For Real Time Structural Health Monitoring, Matthew Boehle, Qiong Jiang, Lingchuan Li, Alexandre Lagounov, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

In order to more effectively monitor the health of composite structures, a fuzzy fiber sensor has been developed. The fuzzy fiber is a bundle of glass fibers with carbon nanotubes or nanofibers (CNTs or CNFs) grown on the surface. The nanotube coating makes the fiber bundle conductive while the small conductive path increases sensitivity. The fuzzy fiber sensor can replace conventional metal foil strain gauges in composite applications. The electrical response of the sensor is monitored in real time to measure strain, vibration, cracking and delamination. Continuous monitoring provides instant notification of any problems. Implementation of this sensor network in …

Design Mixers To Minimize Effects Of Erosion And Corrosion Erosion, Julian B. Fasano, Eric E. Janz, Kevin J. Myers

Chemical and Materials Engineering Faculty Publications

A thorough review of the major parameters that affect solid-liquid slurry wear on impellers and techniques for minimizing wear is presented. These major parameters include (i) chemical environment, (ii) hardness of solids, (iii) density of solids, (iv) percent solids, (v) shape of solids, (vi) fluid regime (turbulent, transitional, or laminar), (vii) hardness of the mixer's wetted parts, (viii) hydraulic efficiency of the impeller (kinetic energy dissipation rates near the impeller blades), (ix) impact velocity, and (x) impact frequency. Techniques for minimizing the wear on impellers cover the choice of impeller, size and speed of the impeller, alloy selection, and surface …

Betaine Chloride-Betaine Tetrachloridoferrate(Iii)—An Ionic Liquid Related Crystal Structure Governed By The Pearson Concept, Anja V. Mudring, Tobias Backer

Anja V. Mudring

The first betaine chloride tetrachloroidoferrate(III) double salt, (Hbet)2Cl[FeCl4] = (Hbet)Cl·(Hbet)[FeCl4], was obtained from a solution of betaine hydrochloride (HbetCl) and FeCl3∙6 H2O in water. The crystal structure (orthorhombic, Pbcm, a = 6.2717(13), b = 12.841(3), c = 25.693(5) Å, Z = 4) is characterized by layers of tetrachloridoferrate(III) anions separated by chloride-bridged, H-bond mediated cationic (Hbet) dimers. The hydrogen bonding network in the crystal structure follows the Pearson HSAB (hard acid-soft base) concept: According to the Pearson concept, the chloride anions show high affinity to the carboxyl group (hard acid and base), and the tetrachloroidoferrate(III) anion preferentially interacts with the …

Limited Thermal Conductance Of Metal-Carbon Interfaces, Jaime J. Gengler, Sergei V. Shenogin, John E. Bultman, Ajit K. Roy, Andrey A. Voevodin, Christopher Muratore

Chemical and Materials Engineering Faculty Publications

The thermal conductance for a series of metal-graphite interfaces has been experimentally measured with time-domain thermoreflectance (TDTR). For metals with Debye temperatures up to ∼400 K, a linear relationship exists with the thermal conductance values. For metals with Debye temperatures in excess of ∼400 K, the measured metal-graphite thermal conductance values remain constant near 60 MW m−2 K−1. Titanium showed slightly higher conductance than aluminum, despite the closeness of atomic mass and Debye temperature for the two metals. Surface analysis was used to identify the presence of titaniumcarbide at the interface in contrast to the aluminum and gold-carbon interfaces (with …