Materials Science and Engineering Commons^™

Enhancing Compatibility And Mechanical Properties Of Natural Rubber Composites, Krisma Yessi Sianturi, Adam Febriyanto Nugraha, Belle Kristaura, Mochamad Chalid

Journal of Materials Exploration and Findings

Pure natural rubber (NR) exhibits low mechanical properties, necessitating the incorporation of additives like vulcanizing agents and fillers. Carbon black and silica, conventional fillers, are relatively expensive and not environmentally friendly. This study explores using Oil Palm Empty Fruit Bunch (OPEFB) fiber as an affordable, abundant, and biodegradable alternative filler for NR. However, compatibility issues arise between the nonpolar NR and the polar OPEFB fiber. A latex-starch hybrid coupling agent (CA (NR-St)) was added to the composite formulation to address this. NR, OPEFB fiber, and the coupling agent were mixed using an open roll mill with a 10 phr OPEFB …

Separation Of Organic Acids Through Direct Catalysis From Sugars, Katelyn Robinson

Chemical Engineering Undergraduate Honors Theses

Society relies on plastic products, whether they are single use or durable. A downside of plastic is that the most common type is a product of oil and oil is not only a limited resource but also a climate-damaging resource. Polylactic acid (PLA) is a bio-based, biodegradable plastic. However, the process of converting biomass to polylactic acid polymer has the largest environmental impact of the PLA production process, so alternative methods of conversion are needed (Moretti et al., 2021). The polylactic acid polymer can be made with lactic acid, which can be converted from glucose.

Mesoscale Modeling Of Controlled Degradation In Polymer Networks And Melts, Vaibhav Palkar

All Dissertations

Controlled degradation of polymers finds various applications in fields ranging from the design of functional soft materials to recycling of polymers. In several of these applications, the characteristic length scale at which relevant processes occur ranges from nanometers to microns, typically referred to as the mesoscale. Although analytical models and continuum approaches inform our current understanding, analysis of degradation at the mesoscale is exceptionally limited. For modeling degradation at the mesoscale, we use the Dissipative Particle Dynamics (DPD) technique and the LAMMPS simulation software. Within the DPD framework, we model controlled degradation or the breaking of covalent bonds within a …

Comparative Analysis On Low Cost Continuous Carbon Fiber Polypropylene Composite Using Compression Molding And Automated Tape Placement, Benjamin U. Schwartz

Masters Theses

Carbon fiber reinforced plastics (CFRP) are widely used throughout the aerospace industry where a weight reduction remains the highest priority with less emphasis on cost. Textile grade carbon fiber (TCF) and other low cost carbon fiber (LCCF) alternatives have recently emerged for use in the automotive market where emissions regulations have pushed automotive manufacturers and research institutions to look for cost effective light weight materials. Fiber reinforced thermoplastics provide an effective solution that align with automotive design including low cost, high processing rates, high impact toughness, unlimited shelf life, and recyclability.

TCF and Zoltek_PX35 fibers are two LCCF aimed at …

Analytical And Experimental Investigation Of Interphase And Dispersion Effects On The Mechanical Stiffness Of Cellulose Nanocomposites, Will Goldberg

McKelvey School of Engineering Theses & Dissertations

The effect of dispersion and interphase properties on the elastic behavior of cellulose nanocomposites was investigated using a number of composite models, experimental data and a thorough literature review. Cellulose nanocomposites consisting of soy protein isolate (SPI) and cellulose nanocrystals (CNC) or polydopamine coated cellulose nanocrystals (PD-CNC) were prepared via solution casting method and tested for mechanical stiffness. These outcomes were compared to standard composite models as well as novel methods adapted from the literature that incorporate data regarding dispersion quality and interphase properties. The literature review verified that both dispersion and interphase properties are highly dependent on interfacial chemistry …

Lignin Copolymer Property Prediction Using Machine Learning, Collin Larsen

Chemical Engineering Undergraduate Honors Theses

Lignin, an abundant biopolymer, is a waste byproduct of the paper and pulp industry. Despite its renewable nature and potential applicability in various products, such as plastics and composites, the development of lignin-based materials has been impeded by the cumbersome, Edisonian process of trial and error. This research proposes a novel approach to forecasting the properties of lignin-based copolymers by utilizing a recurrent neural network (RNN) based on the Keras models previously created by Tao et al. Example units of modified lignin were synthesized via esterification and amination functional group modifications. To increase the efficiency and accuracy of the prediction …

Formulation And Optimization Of Algae-Filled Polylactic Acid Thermoplastic Compounds For Improved Biodegradation, Sydney A. Cole

Honors Theses

Conventional plastics derived from non-renewable petrochemicals – especially from fossil reserves – have become an integral part of human life because their structure can be chemically manipulated to obtain a wide range of properties and geometries necessary in nearly all industries. The volume and rate at which petroleum plastics are produced, used, and discarded has incited several significant issues related to human health, environmental conservation, and ecological biodiversity. To address these issues, many institutions have begun investigating solutions in both the development and end-oflife phases of plastic production and waste. In this thesis, a Chlorella-dominated algae mixture is dried and …

Elucidating The Mechanical And Transport Properties Of Lignin-Based Hydrogel Composites, Nicholas Gregorich

All Dissertations

The use of lignin in the fabrication of soft composites has become an emerging area of research in polymer science and polymer chemistry. These lignin-based materials present numerous benefits, notably, a reduction in the use of petroleum-based precursor, improved structural benefits to otherwise soft host polymers, as well as the inherent antimicrobial and antioxidant properties of lignin, making it suitable for biomaterials. Herein, we present two chemical reaction pathways of incorporating lignin that was fractionated and cleaned using the Aqueous Lignin Purification with Hot Agents (ALPHA) process into poly(vinyl alcohol) (PVA) hydrogel composites for aqueous-based separations. By leveraging the ALPHA …

Poly(Ether Imide)S: Synthesis And Properties, Rachel Price

Honors College Theses

The synthesis of strong polymers is crucial to the creation of heat-resistant, durable, and mechanically useful plastics that we use every day. Poly(ether imide)s are used in applications such as food service, aerospace, automotive, and many more. This thesis will discuss the synthesis and properties of these plastics to help express a larger understanding of these polymers.

Shape Memory Polymer-Based Multifunctional Syntactic Foams, Siavash Sarrafan

LSU Doctoral Dissertations

With the increase in popularity of shape memory polymers (SMPs), especially in applications such as aerospace, textile, biomedical engineering, and even structures, the weight of the material and the devices made with it has always been a crucial factor. Using the shape memory polymer as a matrix to make a syntactic foam is one of the best and most affordable approaches to creating a lighter material that still has the shape memory effect. The addition of particles of different stiffness, strength, and size, with variable fractions, creates a composite that enables engineering the mechanical, as well as other physical and …

Polyesters Derived From Biobased 1,5-Pentanediol For Coatings, Adhesives, And Biodegradable Plastics, Lei Zheng

Doctoral Dissertations

Biomass-derived polymers are drawing increased attention from researchers due to unique performance attributes, potential for biodegradability, new low-cost feedstocks, and improved sustainability. Biobased feedstocks are employed in both major applications of polymers thermosets and thermoplastics. For thermoset coatings and adhesives, biobased resins such as biobased alkyds, epoxy resins, benzoxazine resins, starch derivatives, and proteins from plants and animals, are promising candidates to replace petroleum-derived counterparts. Thermoplastics such as polyethylene are mainly produced from fossil resources, generally have poor degradability and are difficult to effectively recycle. Currently, in the United States, less than 10% plastics are recycled, and more than 70% …

Polymer Based Energy Storage And Thermal Management On Textile Devices, Wesley A. Viola

Doctoral Dissertations

Humans developed textiles to manage thermal energy transfer with the environment and support homeostasis in a wide range of climates. With the anticipation of wearable technologies to transform healthcare via early, pre-symptomatic detection of illness, there is now a demand for electrical energy storage to support such on-body devices. Finding energy materials to merge seamlessly with textiles is basic requirement to ensure widespread adoption of wearable health monitors. Here we use a vapor deposition process to conformally coat ordinary fabrics with the doped conjugated polymer poly(3,4 ethylenedioxythiophene) (PEDOT-Cl), a soft material which possesses electronic and redox capabilities. We demonstrate PEDOT-Cl …

Controlling Mechanical Properties Of Well-Defined Polymer Networks, Ipek Sacligil

Doctoral Dissertations

Polymer networks are one of the most versatile and highly studied material class that revolutionized many aspects of life. Connecting the final network properties to the molecular parameters of its building blocks remains a major research thrust. Recent advances in network synthesis techniques allowed for accurate predictions of elastic modulus in model networks. Tew Group has developed highly efficient, thiol-norbornene networks with controllable mechanical properties. Chapter 2 focuses on modifying the gel fracture energy predicted by Lake-Thomas theory by accounting for loop defects. This study allowed for a priori estimates of gel fracture energy by combining theory, experiments, and simulations. …

Bottom-Up Morphological Control Of Biphasic Polymer Particles Via Heterogeneous Polymerization, Heather S.C. Hamilton

Doctoral Dissertations

Heterogeneous polymerization techniques are industrially relevant, scalable methods to synthesize polymer colloids and they have emerged in recent decades as viable methods to produce biphasic and morphologically complex polymer particles. The overarching goal of this thesis is to understand how heterogeneous polymerization techniques can be modified and optimized to control particle morphology through the systematic study of process parameters. Chapter 1 introduces relevant nomenclature and provides a brief historical perspective on the development of heterogeneous polymerization. This chapter also reviews the state-of-the-art techniques used to prepare morphologically complex polymer particles, with an emphasis on the heterogeneous polymerization processes studied in …

Effect Of Chemical Identity And Morphology On Amphiphilic-Zwitterionic Block Copolymer Membranes, Ria Ghosh

Doctoral Dissertations

Amphiphilic block copolymers have gained a broad research interest attributed to their self-assembly properties over a range of pH, temperature, and ionic strength. Polyzwitterions have attracted special attention due to their hydrophilicity, charge sensitivity and coulombic attraction of the opposite charges over a range of environments making them a popular material of study in the field of stimuli responsive systems, for example in self-healing hydrogels, and water transport membranes. Combining the stimuli responsiveness and higher hydrophilicity of zwitterionic polymers with self-assembly behavior of amphiphilic block copolymers created an interest to study the effect of composition and identity of the zwitterionic …

Vapor Deposition Of Self-Wrinkling Polymer Films, Robert N. Enright

Doctoral Dissertations

Initiated chemical vapor deposition is used to grow polymer films on substrates of various three-dimensional shapes which exhibit wrinkling during film growth, termed self-wrinkling. Self-wrinkling avoids separate film growth and compression steps and more-closely mimics processes observed in nature. The self-wrinkling process is elucidated on flat elastic substrates, revealing control over the amount of compressive stress by changing deposition conditions. Next, a study of films grown on liquid substrates with interface profiles that either resemble cylinders or contain repeating concave cones, saddles, and bowls affirms the principle that the wrinkle roundness increases with interface curvature. The selection of high versus …

Additive Manufacturing For Phase Change Thermal Energy Storage And Management, Thomas B. Freeman

Doctoral Dissertations and Master's Theses

Phase change materials can enhance the performance of energy systems by time shifting or reducing peak thermal loads. Certain electronic devices such as batteries, laser systems, or electric vehicle power electronics are highly transient and require pulse heat dissipation. Heat sinks, or thermal management devices made of a phase change material can absorb large heat spikes while maintaining a constant temperature. Additive manufacturing techniques hold tremendous potential to enable co-optimization of material properties and device geometry, while potentially reducing material waste and manufacturing time. Recently, a few efforts have emerged that employ additive manufacturing techniques to integrate a phase change …

Flexible Materials And Applications For Wearable Sensors, Brock Ferrari

Senior Honors Theses

This literature review aimed to address the limitations of rigid wearable sensors in the medical community by investigating the development of flexible materials for remote health monitoring. A keyword search was conducted on Google Scholar, PubMed, and the Jerry Falwell Library, which yielded 9,102 articles. After applying filtering techniques, the results were narrowed down to 21 articles, which were categorized into "Present Market Conditions," "Flexible Materials for Medical Use," "Applications for Wearable Sensors," and "Potential Use Cases." Discussions were held on prominent materials such as substrate, nanocomposite, and liquid metal materials, exploring their potential applications for chemical and physical sensing, …

Polyethersulfone Thin-Film Nanocomposite Membrane Embedded With Amine-Functionalized Graphene Oxide For Desalination Applications, Ahmed Bahaeldin

Theses and Dissertations

Thin-film nanocomposite (TFN) desalination membranes were prepared based on a polyethersulfone (PES) support, where the polyamide (PA) layer was embedded with amine-functionalized graphene oxide (GO). The effect of adding various concentrations of functionalized and un-functionalized GO on the desalination performance, hydrophilicity, and morphology of the membranes was additionally assessed throughout this work. Scanning electron microscopy (SEM) measurements were used to assess the morphology of the membranes in combination with Brunauer-Emmett-Teller (BET) analysis. Contact angle measurements were used to gauge the hydrophilicity of the synthesized membranes. The membrane with the best desalination performance contained 1x10^-3 wt/vol% of functionalized GO in …

Supplementary Code For "Chain Trajectories, Domain Shapes And Terminal Boundaries In Block Copolymers", Benjamin R. Greenvall, Michael S. Dimitriyev, Gregory M. Grason

Data and Datasets

Supplementary code used for the publication "Chain trajectories, domain shapes and terminal boundaries in block copolymers" by Benjamin R. Greenvall, Michael S. Dimitriyev, and Gregory M. Grason. Includes code for extracting and analyzing polar order and chain trajectories from self-consistent field calculations of block copolymers.

Constructing A Fine Dispersion And Chemical Interface Based On An Electrostatic Self-Assembly And Aqueous Phase Compound In Go/Sio2/Sbr Composites To Achieve High-Wear Resistance In Eco-Friendly Green Tires, Rui Zhang, Jiaye Li, Stephen Jerrams, Shui Hu, Shipeng Wen, Ligun Zhang

Articles

The hazard to the ecosystem caused by rubber microparticles generated from tire abrasion has been a constant concern. Therefore, to protect this ecosystem, the development of a tire tread with high abrasion resistance is especially significant. Herein, γ-aminopropyltriethoxysilane (APTES) was used to modify graphene oxide (GO) and silica (SiO2) to obtain GO and SiO2 with positive charges (NG and NS). Furthermore, NG and NS were electrostatically self-assembled by using maleic anhydride (MAH) hydrolysis, thereby obtaining composite particles (NG-NS) with “bridged structures”. Also, the NG-NS/styrene butadiene rubber (SBR) compounds possessing fine dispersion of NG-NS were prepared by the aqueous compounding method. …

Study Of Nanocomposite Materials Using Molecular Dynamics, Prashik Sunil Gaikwad

Dissertations, Master's Theses and Master's Reports

There is an increase in demand for new lightweight structural materials in the aerospace industry for more efficient and affordable human space travel. Polymer matrix composites (PMCs) with reinforcement material as carbon nanotubes (CNTs) have shown exceptional increase in the mechanical properties. Flattened carbon nanotubes (flCNTs) are a primary component of many carbon nanotube (CNT) yarn and sheet materials, which are promising reinforcements for the next generation of ultra-strong composites for aerospace applications. These flCNT/polymer materials are subjected to extreme pressure and temperature during curing process. Therefore there is a need to investigate the evolution of properties during the curing …

Elastoplastic Quasi-Static And Impact Load Response Of Steel Structure Sub-Assemblage With Cfrp Strips, Ali Al Aloosi, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

Presented in this paper is the outcome of an experimental investigation of the elastoplastic quasi-static and impact load response of a steel sub-assemblage constructed using a pair of hollow square section members with or without Carbon Fiber Reinforced Polymer (CFRP) strips. The sub-assemblage consists of a long structural member welded to a short member, thus representing a typical combination of a column and a beam on the face of a multi-story steel building frame. The column is subjected to a lateral quasi-static or impact load. Tests are conducted on four separate steel sub-assemblages. The first two tests are conducted with …

Higher-Order Effects In Biaxial Flexure Of Gfrp I-Section Beams, Zia Razzaq, Faridoon Z. Razzaq

Civil & Environmental Engineering Faculty Publications

A theoretical study of Glass Fiber Reinforced Polymer (GFRP) beams subjected to biaxial bending moments is presented with a focus on the influence of higher-order effects on maximum normal stresses. It is shown that the biaxial bending type of loading causes a dramatic increase in the maximum normal stress for a GFRP beam when induced torsional effects are included. The study demonstrates that the traditional first-order theory can grossly underestimate the maximum normal stress in a GFRP beam. Based on the numerical results presented using a higher-order theory which also accounts for induced warping normal stresses, the maximum normal stress …

Molecular Dynamics Modeling Of Polymers For Aerospace Composites, Swapnil Sambhaji Bamane

Dissertations, Master's Theses and Master's Reports

Polymer matrix composite materials are widely used as structural materials in aerospace and aeronautical vehicles. Resin/reinforcement wetting and the effect of polymerization on the thermo-mechanical properties of the resin are key parameters in the manufacturing of aerospace composite materials. Determining the contact angle between combinations of liquid resin and reinforcement surfaces is a common method for quantifying wettability. It is challenging to determine contact angle values experimentally of high-performance resins on CNT materials such as CNT, graphene, bundles or yarns, and BNNT surfaces. It is also experimentally difficult to determine the effect of polymerization reaction on material properties of a …

Drop Wetting And Sliding On Soft, Swollen Elastomers, Zhuoyun Cai

Theses and Dissertations--Chemical and Materials Engineering

Soft, slippery surfaces have gained increasing attention due to their wide range of potential applications, for example in self-cleaning, anti-fouling, liquid collection, and more. One design approach in creating slippery surfaces is using a swollen elastomer, which is a polymer network swollen with a lubricant. This type of surface may be beneficial for longer-term use than standard lubricant-infused surfaces, and provides a versatile surface with tunable mechanical properties. Hence, understanding the physics of soft surface interactions is important for fundamental soft matter physics, biomaterials, adhesives, and coatings. This research experimentally investigates wetting on soft infused networks, with the aim of …

Exposure To Pcb126 During The Nursing Period Reversibly Impacts Early-Life Glucose Tolerance, Brittany B. Rice, Keegan W. Sammons, Sara Y. Ngo Tenlep, Madeline T. Weltzer, Leryn J. Reynolds, Cetewayo S. Rashid, Hollie I. Swanson, Kevin J. Pearson

Human Movement Sciences & Special Education Faculty Publications

Polychlorinated biphenyls (PCBs) are persistent environmental organic pollutants known to have detrimental health effects. Using a mouse model, we previously demonstrated that PCB126 exposure before and during pregnancy and throughout the perinatal period adversely affected offspring glucose tolerance and/or body composition profiles. The purpose of this study was to investigate the glucose tolerance and body composition of offspring born to dams exposed to PCB126 during the nursing period only. Female ICR mice were bred, and half of the dams were exposed to either vehicle (safflower oil) or 1 µmole PCB126 per kg of body weight via oral gavage on postnatal …

Solid-State Shear Pulverization: A Comprehensive Study On Polymer Processing Technology From A Systematic Innovation Perspective, Tyler A. Will

Master’s Theses

Solid-state shear pulverization (SSSP) is a continuous and scalable processing technique that imposes mechanochemical changes in polymer-based materials. It has been shown to impart beneficial properties onto homopolymers or create copolymers and composites through continuous fragmentation and fusion. The unique technology employs cold temperature to keep the polymer in the solid state. This thesis investigates industrial polymer processing in the context of real-world applications. This thesis analyzes SSSP using an organized methodology called systematic innovation (SI). SI facilitates problem solving by assisting engineers in conducting root cause analysis around a material and studying the physical setup of the equipment.

This …

Temperature-Dependent Diffusion In Block Copolymer Organogels, Ridwana Bashar

Master’s Theses

Organogels are often considered for transport-based applications such as transdermal drug delivery vehicles and gel actuators due to their unique properties. Recent consideration of styrenic block copolymer based organogels’ application in transdermal drug delivery requires an extensive investigation of drug diffusion behavior through these gels to assess their applicability. Temperature is a major influencing parameter on diffusion. The goal of this research is to better understand the impact of temperature on diffusion in styrenic triblock copolymer organogels. To accomplish this goal, we focused on three specific objectives: (i) accurately measure the diffusivities of a solute – AOT reverse micelles – …

Defining The Proper Operating Time For The Septa Extractor, Abigail Jones

Williams Honors College, Honors Research Projects

Anionic polymerizations are a common type of reaction used to produce synthetic rubber. During these reactions, it is necessary to charge initiators, modifiers, and other substances, through pressurized containers that are sealed with rubber septa. These septa prevent oxygen and moisture from entering the pressurized container, and the reactor, though they need to be cleaned before use to remove other impurities. Currently a glass Soxhlet Extractor is used to remove such impurities, and though effective, it has a limited capacity, so it has to run frequently. This limitation led to the commissioning of the Septa Extractor, which is an automated …