Mechanics of Materials Commons^™

Characterization And Modeling Of Asphalt Concrete For Dynamic Properties And Performances, A S M A. Rahman

Civil Engineering ETDs

The recently developed mechanistic-empirical pavement design guide (MEPDG, also known as Pavement M-E design method) uses the nationally calibrated, binder viscosity-based dynamic modulus predictive model for the design and analysis of asphalt pavements. In this study, this model is assessed for its appropriateness for asphalt-aggregate mixtures typically used in New Mexico. In essence, this study investigates the predictability issue of complex modulus of New Mexico mixes. A total of 54 Superpave mixes with different aggregate gradations, air voids, and binder grades were collected from the mixing plants and from the pavement construction sites. The loose asphalt mixtures were then compacted, …

A Comparison Study Of Composite Laminated Plates With Holes Under Tension, Joun S. Kim

Master's Theses

A Comparison Study of Composite Laminated Plates with Holes under Tension

A study was conducted to quantify the accuracy of numerical approximations to deem sufficiency in validating structural composite design, thus minimizing, or even eliminating the need for experimental test. Error values for stress and strain were compared between Finite Element Analysis (FEA) and analytical (Classical Laminated Plate Theory), and FEA and experimental tensile test for two composite plate designs under tension: a cross-ply composite plate design of [(0/90)4]s, and a quasi-isotropic layup design of [02/+45/-45/902]s, each with a single, centered hole of 1/8” diameter, and 1/4" diameter (four sets …

Effect Of Ultrasonic Treatment On The Microstructure And Mechanical Properties Of Al6061 And Composite, Ana S. Exime

FIU Electronic Theses and Dissertations

In this study, the effect of ultrasonic treatment (UST) parameters such as amplitude, sonication time, and melt temperature on microstructure and microhardness of Al 6061 alloy is evaluated. The effect of UST on the dispersion of tungsten disulfide (WS₂) and carbon nanotubes (CNT) as reinforcement particles in Al 6061 during casting is also studied. The cast Al 6061 with UST demonstrated 32% grain size reduction and 8% increase in the microhardness for optimum processing conditions. The cavitation process induced by UST is responsible for the refinement in microstructure and increase of hardness by enhancing the degassing and nucleation …

Development Of The End-Effector Of A Cable-Driven Parallel Manipulator For Automated Crop Sensing, Iman Salafian

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

A four cable-driven parallel manipulator (4CDPM), consisting of sophisticated spectrometers and imagers, is under development for use in acquiring phenotypic and environmental data over an acre-sized maize field. This thesis presents the design, controls, and testing of two sub-systems in a 4CDPM: a Center of Mass Balance System (CMBS) and a Drop-Down System (DDS).

One of the factors that influences stability is the center of mass (COM) position of the end effector. An offset in COM can cause a pendulum effect or an undesired tilt angle. A center of mass balancing system is presented in this thesis to minimize the …

The Mathematical Theory Of Deformation Arrest In Large-Strain Dynamic Plasticity, Brendan A. Kullback

Mechanical Engineering ETDs

Ductile structural components subjected to explosive loadings exhibit a large range of behaviors. The response of beams, walls, and blast doors is estimated using two methods. The engineering level approaches are highly simplified and neglect much of the relevant physics while the use of finite element or shock-code simulation is expensive and not suited to rapid problem solving and parameter studies. In this dissertation, a medium fidelity reduced order modeling approach has been derived to capture the most relevant physics governing rupture of ductile bodies dynamically deforming in tension.

Solution of the inertially stretching jet is used to reveal the …

Negahban Group Report: Saw-Tooth Shear Response Of Aged Poly(Methyl Methacrylate) (Pmma), Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

Results for isothermal saw-tooth shear loading experiments conducted on annealed and oven-cooled poly(methyl methacrylate) (PMMA) at temperatures between 50^oC and 140^oC. The experiments were conducted 1996.

Formation Of Mound-Like Multiscale Surface Structures On Titanium By Femtosecond Laser Processing, Edwin Peng, Alfred Tsubaki, Craig A. Zuhlke, Ryan Bell, Meiyu Wang, Dennis R. Alexander, George Gogos, Jeffrey E. Shield

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Surface Functionalization Technique • Femtosecond Laser Surface Processing (FLSP) • Utilize high power, femtosecond (10-15 s) laser pulses • Produce self-organized, multiscale surface micro/nanostructures • Diverse range of applicable substrates: semiconductors, metals, polymers, & composites

Why? • What are the different types of FLSP structures on Ti? • Physical evidence needed for FLSP formation models • Optimize FLSP of Ti for biomedical & other applications

How? • Obtain evidence of mound growth processes by examining underlying microstructure • Utilize dual beam Scanning Electron Microscope-Focused Ion Beam instrument to cross section surface structures & fabricate transmission electron microscopy samples

Tensile Specimen Punch, John Allen

All Undergraduate Projects

This project comes from a need to have tensile specimens made for the MET 351, Metallurgy/Materials and Processes, and 426, Applied Strengths of Materials, labs. This punch is designed to be used with an arbor press to create the desired tensile specimen shape out of plastic blanks. The initial concept was suggested by Dr. Craig Johnson. The designs went through many changes, for example getting rid of the sides originally proposed to hold the specimen in place, and modifications to other parts to make them more efficient. Additional parts were also added to the design with the help and advice …

Asme Baja Rc Car Drivetrain, Walter Lackey

All Undergraduate Projects

The ASME Baja car is a student built radio controlled car, which will compete with other schools in a variety races. The drivetrain aspect of the car must smoothly transfer power from the motor to the rear wheels of the car. The drivetrain must be designed in collaboration with the other team member’s suspension system to avoid interference. The majority of the parts in the drivetrain are purchased parts intended for various applications. These parts were chosen based on their proximity to the optimal calculated values. Power flows from the electric motor through a single gear reduction, then through a …

Anisotropy Evolution Due To Surface Treatment On 3d-Printed Fused Deposition Modeling (Fdm) Of Acrylonitrile Butadiene Styrene (Abs), Blake E. Lozinski

Honors Undergraduate Theses

Purpose: This paper will present insight to the methodology and results of the experimental characterization of Acrylonitrile Butadiene Styrene (ABS) using Fused Deposition Modeling (FDM). The work in this research explored the effects of print orientation, surface treatment, and ultraviolet (UV) light degradation with the utilization of Digital Image Correlation (DIC) on ABS tensile specimens.

Design/methodology: ABS specimens were printed at three build orientations (flat (0 degrees), 45 degrees, and up-right (90 degrees)). Each of these specimens were treated with three different surface treatments including a control (acrylic paint, Cyanoacrylate, and Diglycidyl Bisphenol A) followed by exposure to UV light …

Investigation Of Electrical Defects Arising From Excessive Sidewall Force And Excessive Tensile Strain On Power Cables, Darren Mcconnon, Joseph Kearney, Tom Looby, James O'Shaughnessy

Conference papers

The study includes a comprehensive review of the existing literature and guidelines regarding the effects of sidewall force and tensile strain on power cables during installation. The most appropriate diagnostic test methods required to analyse these effects are also assessed. The results of tests and analysis of the existing literature are then combined in an attempt to determine a realistic basis for guidelines and recommendations relevant to cable installation forces.