Engineering Science and Materials Commons^™

Microstructure Control And Correlation To Creep Properties In Grade 91 Steel Weldment After Thermo-Mechanical Treatments And An Fe-30cr-3al Alloy Strengthened By Fe2nb Laves Phase, Benjamin Allen Shassere

Doctoral Dissertations

Type IV cracking in weldments of steel pipes after creep deformation is a concern in modern fossil-fueled power plants. Two possible methods for minimizing or eliminating Type IV cracking will be discussed. The first method alters the initial microstructure of typical Grade 91 steel base metal before welding, while the second provides baseline microstructure characteristics and creep performance of a new alloy that is strengthened by the intermetallic Fe2Nb Laves phase. The initial microstructure of the Grade 91 steel can be controlled by Thermo-Mechanical Treatments, which aids in precipitation of fine (5-10 nm) MX particles in austenite before transformation to …

Microstructural Analysis Of Thermoelastic Response, Nonlinear Creep, And Pervasive Cracking In Heterogeneous Materials, Alden C. Cook

Electronic Theses and Dissertations

This dissertation is concerned with the development of robust numerical solution procedures for the generalized micromechanical analysis of linear and nonlinear constitutive behavior in heterogeneous materials. Although the methods developed are applicable in many engineering, geological, and materials science fields, three main areas are explored in this work. First, a numerical methodology is presented for the thermomechanical analysis of heterogeneous materials with a special focus on real polycrystalline microstructures obtained using electron backscatter diffraction techniques. Asymptotic expansion homogenization and finite element analysis are employed for micromechanical analysis of polycrystalline materials. Effective thermoelastic properties of polycrystalline materials are determined and compared …

Development Of Lignin Carbon Fiber And Reinforced Composites, Nathan Kieran Meek

Masters Theses

The aim of this work is to develop lignin carbon fiber for composite applications. This included mechanical testing of single lignin carbon fiber (LCF), interfacial shear strength determination for LCF-resin systems using single fiber fragmentation, x-ray diffraction for the evaluation of microstructural parameters, and finally composite manufacturing and testing. Through these focused areas of analysis, the carbon fiber is thoroughly characterized and composite performance is evaluated. This effort was a collaboration with the Center for Renewable Carbon (CRC) and the Civil and Environmental Engineering Department. LCF produced by the CRC resulted in fibers having tensile strength of 250-800 MPa and …

Structure-Property Relationships Of Polyisobutylene-Block-Polyamide Thermoplastic Elastomers, Morgan Dunn Heskett

Master's Theses

Thermoplastic elastomers (TPEs) are a class of polymer fit for a wide variety of applications due to their customizability. In the synthesis of these types of materials, an elastically-performing polymer, deemed the “soft block,” is combined with a stiffer “hard block” polymer, each of which can be selected based on their own specific properties in order to achieve desired material behavior in the final copolymer. Recently, the use of polyisobutylene as a soft block in combination with a polyamide hard block has been investigated for use in TPE synthesis. While the material showed some promising behavior, many properties were still …

Sulfate Resistance Of Nanosilica Contained Portland Cement Mortars, Iani Batilov Batilov

UNLV Theses, Dissertations, Professional Papers, and Capstones

Soils, sea water and ground water high in sulfates are commonly encountered hostile environments that can attack the structure of concrete via chemical and physical mechanisms which can lead to costly repairs or replacement. Sulfate attack is a slow acting deteriorative phenomenon that can result in cracking, spalling, expansion, increased permeability, paste-to-aggregate bond loss, paste softening, strength loss, and ultimately, progressive failure of concrete. In the presented research study, Portland cement (PC) mortars containing 1.5% to 6.0% nanosilica (nS) cement replacement by weight were tested for sulfate resistance through full submersion in sodium sulfate to simulate external sulfate attack. Mortars …

Alkali-Activated Natural Pozzolan/Slag Binder For Sustainable Concrete, Meysam Najimi

UNLV Theses, Dissertations, Professional Papers, and Capstones

This study aimed to fully replace Portland cement (PC) with environmentally friendly binders capable of improving longevity of concrete. The new binders consisted of different proportions of natural Pozzolan and slag which were alkaline-activated with various combinations of sodium hydroxide and sodium silicate. A step-by-step research program was designed to (1) develop alkali-activated natural Pozzolan/slag pastes with adequate fresh and strength properties, (2) produce alkali-activated natural Pozzolan/slag mortars to assess the effects of dominant variables on their plastic and hardened properties, and (3) finally produce and assess fresh, mechanical, dimensional, transport and durability properties of alkali-activated natural Pozzolan/slag concretes. The …

Cold Gas Dynamic Spray – Characterization Of Polymeric Deposition, Trenton Bush

Masters Theses

When a solid, ductile particle impacts a substrate at sufficient velocity, the resulting heat, pressure, and plastic deformation can produce bonding at the interface. The use of a supersonic gas flow to accelerate such particles is known as Cold Spray deposition. The Cold Spray process has been commercialized for some metallic materials, but further research is required to unlock the exciting material properties possible with polymeric compounds. In this work, a combined computational and experimental study a) simulated and optimized the nozzle flow conditions necessary to produce bonding in a polyethylene particle, b) developed and fabricated an experimental device, and …

Numerical Studies For Improving Fracture Toughness Resistance Curve Testing Using Single-Edge (Notched) Tension Specimens, Yifan Huang

Electronic Thesis and Dissertation Repository

The fracture toughness resistance curve, i.e. the J-integral resistance curve (J-R curve) or the crack tip opening displacement resistance (CTOD-R) curves, is widely used in the integrity assessment and strain-based design of energy pipelines with respect to planar defects (i.e. cracks). This thesis deals with issues related to the experimental determination of the J(CTOD)-R curves using the newly-developed single-edge (notched) tension (SE(T)) specimens. In the first study, the plastic geometry factor, i.e. the η_pl factor, used to evaluate J in a J-R curve test based on …

Forcing Cesium Into Higher Oxidation States Via Useful Hard X-Ray Induced Chemistry At Extreme Conditions, Daniel Thomas Sneed

UNLV Theses, Dissertations, Professional Papers, and Capstones

Recent theoretical work published in Nature Chemistry postulates the existence of cesium in high oxidation states when bonding with fluorine. It is thus predicted to behave as a p-block element (such as xenon) at pressures above 5 GPa. At these pressures, fluorine atoms may bond with the inner p-shell electrons forming CsFn, where n may vary from 2 up to 6; thus the oxidation state of Cs may change up to 6+. My research focused on physically synthesizing these compounds and to verify that, given the right conditions, bonding doesn't only occur with valence electrons, but with the inner p-shell …

Contact Radius And Insulator-Metal Transition In Films Comprised Of Touching Semiconductor Nanocrystals, Deanna M. Lanigan

McKelvey School of Engineering Theses & Dissertations

Nanocrystal assemblies are being explored for a number of optoelectronic applications such as transparent conductors, photovoltaic solar cells, and electrochromic windows. Majority carrier transport is important for these applications, yet it remains relatively poorly understood in films comprised of touching nanocrystals. Specifically, the underlying structural parameters expected to determine the transport mechanism have not been fully elucidated. In this report, we demonstrate experimentally that the contact radius, between touching heavily doped ZnO nanocrystals, controls the electron transport mechanism. Spherical nanocrystals are considered, which are connected by a circular area. The radius of this circular area is the contact radius. For …

Biomimetic Seal Flipper Test Rig, Gordon D. Belyea, Laura Kawashiri, Dylan Rinker, Kurt Beske

Mechanical Engineering

No abstract provided.

Development And Evaluation Of Matrix Material Formulations For Potential Integration Into Immunodiagnostic Biosensors, Payam Aminayi

Dissertations

This study supports the development, characterization and optimization of biosensor material formulations for immunodiagnostic applications based on experimental findings and hypotheses by Wang and Wu [1, 2], and using a test-plate apparatus and thin-film design developed by Young [3].

Certain biosensors working on the basis of conductance/impedance changes have demonstrated their potential to detect various bacteria, enzymes, and biomolecules due to their enhanced electrical properties with incorporated single-walled carbon nanotubes (SWNT). From the work conducted in our laboratory, we are attempting to determine and develop a matrix formulation containing highly dispersed SWNT, antibody and other components that elicit a significantly …

Experimental Building Demonstration Model With Viscous Fluid Dampers, Blake Thomas Reeve, Brianna Jean Kufa, Aden Malek Stepanians, Sophie Carmion Ratkovich

Architectural Engineering

The Architectural Engineering major places a heavy emphasis on structural dynamics and the role of wind and seismic loading in building analysis and design. Buildings of high importance that are critical to community function, such as hospitals, often utilize supplemental damping devices like supplemental viscous fluid dampers or base isolators to reduce the overall demands on the structural system. The design and analysis of these dampers are typically not taught at the undergraduate level, and is frequently performed by mechanical engineers, in lieu of structural engineers.

To better understand and research building behavior with supplemental damping devices, our multi-disciplinary team …

Carbon Fiber Reinforced Polymer Roofing At Ac2 Auditorium: A Case Study, Jacob R. Hague

Construction Management

Carbon Fiber Reinforced Polymer (CFRP) has been used in several capacities in the manufacturing of products such as high performance cars and airplanes, as well as many other smaller products. In construction, it has primarily been used as a way to strengthen or repair existing structures, and in some more recent applications, in tension cables. This paper will examine a new way to use CFRP- as a roofing material, and will specifically focus on the design and installation of a CFRP roof installed at Apple’s new AC2 Auditorium, forming the roof for the main entrance lobby. Installed in February of …

Theory Of Carrier Transport From First Principles: Applications In Photovoltaic And Thermoelectric Materials, Alireza Faghaninia

McKelvey School of Engineering Theses & Dissertations

New sources of energy that are environmentally friendly, cost-effective, and renewable are essential if we are to combat the effects of global climate change. Two of these sources are solar photovoltaic (PV) cells to convert sunlight into electricity and thermoelectric (TE) devices to convert heat to electricity. To be practical on a large scale, the properties (e.g. electrical conductivity, band gap, Seebeck coefficient, etc) of the the underlying materials must be improved significantly through judicious control of structure and composition. Significant understanding of materials properties is required to design and engineer new high-performing materials. First principles calculations using density functional …

Development And Application Of 3-D Fuel Performance Modeling To Assess Missing Pellet Surface Influence On Pellet Clad Interaction And Clad Failure, Nathan Allen Capps

Doctoral Dissertations

In the late 1970s PCI related failures caused the implementation of startup ramp restrictions. These ramp restrictions where intended to reduce the stresses caused by pellet cladding contact. These ramp restrictions had a significant impact on Westinghouse fueled PWRs, reducing PCI related failure until 2003. Through investigation into these fuel rod failures lead to the conclusion that missing pellet surfaces (MPS) were the root cause of the failures. MPS are local geometric defects in nuclear fuel pellets that result from pellet mishandling or the manufacturing process. The presence of MPS defects can cause stress concentrations in the clad of sufficient …

Design Of A Folding V-Scraper With Roller For Orchard Applications, Chase Ulrich

BioResource and Agricultural Engineering

This senior project discusses the design of a folding 15 ft. wide leveler for orchard use. This design utilized a category 2 three-point hitch to connect the implement to a tractor. The folding mechanism uses the tractors hydraulic system to actuate the folding movement using hydraulic cylinders. The blades, when wings in operational position, are rigid with one another after some assembly. When the implement is folded the width is reduced to nine feet.

High-Pressure Properties Of Several Narrow Bandgap Semiconductors From First-Principles Calculations, Andrew Michael Alvarado

UNLV Theses, Dissertations, Professional Papers, and Capstones

The electronic, thermodynamic, and structural properties of three semiconducting materials, ZnO, InN, and PbS, at high pressure are investigated utilizing first-principles calculations based on density function theory. The first two systems, ZnO and InN, crystalize as hexagonal structures at ambient conditions and transition to a cubic structure at higher pressures. The last system, PbS, is cubic at ambient conditions, but transitions to an orthorhombic structure at higher pressure. At ambient conditions, these materials are well known semiconductors with vast amount of research and a variety of wide ranging applications in electrical devices. However, there is a lack of understanding of …

Impedance Spectroscopy Studies Of Yttria Stabilized Zirconia Under Extreme Conditions, Quinlan Blaine Smith

UNLV Theses, Dissertations, Professional Papers, and Capstones

Yttria Stabilized Zirconia (YSZ) is of interest for many industries. Varying amounts of Yttria (Y2O3) can be doped into Zirconia (ZrO2) to create materials with specific characteristics. For instance, 3mol% YSZ (3YSZ) is known to be a super hard material and is used as a coating on drill tips and as an abrasive. Eight mol% YSZ (8YSZ) is commonly used as a solid electrolyte in Solid Oxide Fuel Cells because of its good ionic conducting abilities and stability at high temperatures. In this thesis project, a novel experimental setup was created and used to study the ionic conductivity of (3 …

Modeling And Experimental Investigation On The Influence Of Radiation Defects On Helium Behavior In Bcc Iron, Zuya Huang

Masters Theses

Fe-based alloys are important structural materials for both fission and fusion energy. For fusion applications, the challenges of radiation-induced changes in microstructure, properties and performance is further challenged by the concomitant production of helium from (n, alpha) nuclear reactions and fusion reactions. Due to the lack of a volumetric, high flux 14-MeV neutron source, studying these phenomena require the use of computational materials modeling and novel experimental methods. In this thesis, molecular dynamics (MD) simulations was used to investigate the synergistic interactions of helium with prismatic dislocation loops characteristic of those observed in neutron irradiated iron to determine how the …

Haul Truck Tires Recycling, Jessica N. Lizarazu

Chemical Engineering Undergraduate Honors Theses

The disposal of large Off-the-Road (OTR) tires is an increasingly important concern. These tires can weigh up to 8,450 pounds with an overall diameter and width of approximately 140.7 inches and 45.1 inches respectively. OTR tires are used for mining vehicles such as haul trucks, wheel loaders, backhoes, graders, and trenchers. These new tires cost between $38,000 and $50,000 each, depending on multiple factors including oil prices and the cyclical nature of the industry. Haul trucks contain six tires per vehicle, and mines replace these tires around every 9-12 months. Statistics regarding discarded OTR tires are not provided by the …

Nanoscale Frictional Properties Of Nickel With One-Dimensional And Two-Dimensional Materials, Timothy K. Schlenger

Mechanical Engineering Undergraduate Honors Theses

When looking at the nanoscale, material interface interactions have been observed to exhibit particularly interesting properties. Our research looks into various combinations of carbyne and graphene atop a nickel block to look into the interface friction properties between them. Both the carbyne and graphene are tested using steered molecular dynamics (SMD) in sheering and peeling directions along the surface of the nickel block. These tests are then analyzed by comparing the magnitude of the acting force versus the displacement of the carbon allotrope sample across the nickel block. It is found that as the width of a carbon allotrope sample …

Effect Of Thermal Treatment On High Temperature Deformation Of Alloy Ep-~823, Martin Milburn Lewis

UNLV Theses, Dissertations, Professional Papers, and Capstones

The objective of this research topic is to determine mechanical properties of Alloy EP-823 and to provide a mechanistic understanding of its sensitivity to both thermal treatment and performance temperature. EP-823 is a leading target material for accelerator-driven waste transmutation applications. Overall, the tensile test results of Alloy EP-823 indicated a general trend of decreasing mechanical performance with an increase in tempering time. An increase in tempering time had a statistically significant inverse relationship with ultimate tensile strength (UTS) and yield strength (YS). An increase in tempering time did not have a significant effect on elongation and reduction in area. …

Direct Band Gap Gallium Antimonide Phosphide (Gasbxp1-X) For Solar Fuels., Harry Benjamin Russell

Electronic Theses and Dissertations

Photoelectrochemical water splitting has been identified as a promising route for achieving sustainable energy future. However, semiconductor materials with the appropriate optical, electrical and electrochemical properties have yet to be discovered. In search of an appropriate semiconductor to fill this gap, GaSbP, a semiconductor never tested for PEC performance is proposed here and investigated. Density functional theory (DFT+U) techniques were utilized to predict band gap and band edge energetics for GaSbP alloys with low amount of antimony. The overall objective of this dissertation is to understand the suitability of GaSb_xP_1-x alloys for photoelectrochemical water splitting application. Specifically, …

Kinetics Of Length Scale Dependent Deformation Of Gold Microspheres And Micropillars, A Z M Ariful Islam

Electronic Thesis and Dissertation Repository

In this thesis length and time scale dependence of the operative plastic deformation mechanisms in Au is studied. Uniaxial compression tests were performed at various loading rates on FIB-milled Au micropillars and single-crystalline Au microspheres of diameter ranging from 0.8 to 6.0 µm to investigate the incipient and bulk plasticity events. Constant-load ambient-temperature creep tests were performed on the micropillars to study the time-dependent plasticity at very slow strain rates. Uniaxial compression tests were also performed on coated Au microspheres to study the effect of extrinsic constraint on the deformation mechanisms.

During uniaxial compression, both the Au micropillars and microspheres …

Human-Assisted Fluid Power Vehicle, Aaron Huntoon

Honors Theses

The rising cost of energy has prompted industrial and technology companies to research and implement renewable or green energy sources in every aspect of their business. This green technology can consist of sources such as: solar, wind, fluid, or others to create energy from renewable sources. The use of these various sources reduces the pollution associated with standard methods of energy development, and it will ultimately drive costs down to benefit the general population. One of the largest benefactors to the use of renewable energy sources is the transportation industry. Billions of people rely on various modes of transportation every …

Doped Tio2 Nanowires For Applications In Dye Sensitized Solar Cells And Sacrifical Hydrogen Production, Qasem Alsharari

Electronic Thesis and Dissertation Repository

This thesis explores the synthesis of metal oxide 1-D nanowires using a sol-gel method in supercritical carbon dioxide (sc-CO₂), as an environmental friendly enabling solvent. Porous nanowires were synthesized and their performance was tested in dye sensitized solar cell and sacrifical hydrogen production. Titanium isopropoxide (TIP) was used as a precursor for titania synthesis while copper, bismuth and indium were examined as dopants, respectively. The sol-gel reactions were catalyzed by acetic acid in CO₂ at a temperature of 60 °C and pressure of 5000 psi. It was observed that acetic acid/monomer ratio > 4 produced nanowires while a …

Ramifications Of Projectile Velocity On The Ballistic Dart Penetration Of Sand, Peter Anthony Sable

Master's Theses (2009 -)

With the advent of novel in-situ experimental measurement techniques, highly resolved quantitative observations of dynamic events within granular media can now be made. In particular, high speed imagery and digital analysis now allow for the ballistic behaviors of sand to be examined not only across a range of event velocities but across multiple length scales. In an attempt to further understand the dynamic behavior of granular media, these new experimental developments were implemented utilizing high speed photography coupled with piezo-electric stress gauges to observe visually accessible ballistic events of a dart penetrating Ottawa sand. Projectile velocities ranged from 100 to …

Multi-Axial Failure Of High-Performance Fiber During Transverse Impact, Matthew C. Hudspeth

Open Access Dissertations

The effect of projectile nose geometry on ensuing wave development in high-performance yarns is explored during single yarn transverse impact. Special attention has been placed on visualizing the immediate region around the projectile-yarn contact site for 0.30-cal round, 0.30-cal fragment simulation projectiles (FSP), and razor blades using high-speed imaging. Kevlar® KM2, Dyneema®SK76 and AuTx have been impacted at velocities ranging from ∼100 m/s to ∼1200 m/s depending on projectile nose shape, with an emphasis set on determining the critical velocity wherein below said velocity significant development of wave propagation occurs and above said velocity the yarn fails immediately upon impact. …

A Parameterized Implementation Of A Hybrid Fuzzy Boolean Finite State Machine Using An Fpga, Sean T. Fuller

Masters Theses

A fuzzy system based on the extended Hybrid Fuzzy Boolean Finite State Machine (HFBFSM) model is designed and implemented in a Xilinx Zynq® all programmable System on Chip (SoC). The system allows for a single dominant crisp state and multiple non-dominant states to be activated simultaneously. A method is proposed to calculate the degree of membership of non-dominant states, β, by the distance of defuzzified fuzzy inputs to state transition trigger mechanisms.

The HFB-FSM is was realized by the author using custom logic written in VHDL (Very High Speed Integrated Circuit (VHSIC) Hardware Description Language) in the Programmable Logic (PL) …