Engineering Science and Materials Commons^™

Plaque Burden Influences Accurate Classification Of Fibrous Cap Atheroma By In-Vivo Optical Coherence Tomography In A Porcine Model Of Advanced Coronary Atherosclerosis., Christian B. Poulsen, Ryan M. Pedrigi, Nilesh Pareek, Ismail D. Kilic, Niels R. Holm, Jacob F. Bentzon, Hans Erik Botker, Erling Falk, Rob Krams, Ranil De Silva

Department of Mechanical and Materials Engineering: Faculty Publications

Advanced coronary atherosclerosis assessed by in-vivo optical coherence tomography (OCT) has not been directly compared with histology. In a porcine model with human-like coronary atherosclerosis we compared in-vivo OCT images with histology in five animals. We found a high sensitivity but modest specificity of OCT in classifying fibrous cap atheroma (FCA). The modest specificity was caused by misclassification of FCA lesions as pathological intimal thickening. The misclassification most frequently occurred when plaque burden exceeded ~20%. Compared with histology, OCT has high sensitivity but modest specificity for identifying FCA. The study suggests that plaque burden should be considered when interpreting OCT …

Experimental Measurement Of Dolphin Thrust Generated During A Tail Stand Using Dpiv, Frank E. Fish, Terrie M. Williams, Erica Sherman, Yae Eun Moon, Vicki Wu, Timothy Wei

Department of Mechanical and Materials Engineering: Faculty Publications

Estimation of force generated by dolphins has long been debated. The problem was that indirect estimates of force production for dolphins resulted in low values that could not be validated. Bubble digital particle image velocimetry (DPIV) measured hydrodynamic force production for swimming dolphins and demonstrated high force production. To validate the bubble DPIV and reconcile force production measurements, two bottlenose dolphins (Tursiops truncatus) performing tail stands were measured with bubble DPIV. Microbubbles were generated from a finely porous hose and compressed air source. Displacement of the bubbles by the propulsive motions of the dolphin was tracked with a …

Neuroprotective And Anti-Inflammatory Effects Of Rhus Coriaria Extract In A Mouse Model Of Ischemic Optic Neuropathy, Saba Khalilpour, Ghazaleh Behnammanesh, Fouad Suede, Mohammed O. Ezzat, Jayadhisan Muniandy, Yasser Tabana, Mohamed B. K. Ahamed, Ali Tamayol, Amin Malik Shah Majid, Enrico Sangiovanni, Mario Dell'agli, Aman Shah Majid

Department of Mechanical and Materials Engineering: Faculty Publications

Modulating oxidative stresses and inflammation can potentially prevent or alleviate the pathological conditions of diseases associated with the nervous system, including ischemic optic neuropathy. In this study we evaluated the anti-neuroinflammatory and neuroprotective activities of Rhus coriaria (R. coriaria) extract in vivo. The half maximal inhibitory concentration (IC₅₀) for DPPH, ABTS and B-carotene were 6.79 ± 0.009 µg/mL, 10.94 ± 0.09 µg/mL, and 6.25 ± 0.06 µg/mL, respectively. Retinal ischemia was induced by optic nerve crush injury in albino Balb/c mice. The anti-inflammatory activity of ethanolic extract of R. coriaria (ERC) and linoleic acid (LA) on …

Methods, Systems, And Devices For Surgical Access And Procedures, Shane M. Farritor, Mark Rentschler, Amy Lehman, Stephen R. Platt, Jeff Hawks

Department of Mechanical and Materials Engineering: Faculty Publications

The embodiments disclosed herein relate to various medical device components, including components that can be incorporated into robotic and/or in vivo medical devices. Certain embodiments include various actuation system embodiments, including fluid actuation systems, drive train actuation systems, and motorless actuation systems. Additional embodiments include a reversibly lockable tube that can provide access for a medical device to a patient's cavity and further provides a reversible rigidity or stability during operation of the device. Further embodiments include various operational components for medical devices, including medical device arm mechanisms that have both axial and rotational movement while maintaining a relatively compact …

Methods, Systems, And Devices Relating To Force Control Surgical Systems, Shane M. Farritor, Thomas Frederick, Kearney Lackas, Joe Bartels, Jacob Greenburg

Department of Mechanical and Materials Engineering: Faculty Publications

The various embodiments herein relate to robotic surgical systems and devices that use force and/or torque sensors to measure forces applied at various components of the system or device. Certain implementations include robotic surgical devices having one or more force/torque sensors that detect or measure one or more forces applied at or on one or more arms. Other embodiments relate to systems having a robotic surgical device that has one or more sensors and an external controller that has one or more motors such that the sensors transmit information that is used at the controller to actuate the motors to …

Multifunctional Operational Component For Robotic Devices, Shane M. Farritor, Amy Lehman, Mark Rentschler

Department of Mechanical and Materials Engineering: Faculty Publications

The various embodiments disclosed herein relate to modular medical devices, including various devices with detachable modular components and various devices with pivotally attached modular components. Additional embodiments relate to procedures in which various of the devices are used cooperatively. Certain embodiments of the medical devices are robotic in vivo devices.

Frequency Dependent Deformation Reversibility During Cyclic Loading, Shuai Shao, Michael M. Khonsari, Jian Wang, Nima Shamsaei, Nan Li

Department of Mechanical and Materials Engineering: Faculty Publications

High-frequency testing (HFT) is useful for accelerated fatigue testing of conventional materials that typically serve under low-frequency loading conditions, as well as for the assessment of the robustness of microelectromechanical systems which typically experience high-frequency service conditions. Using discrete dislocation dynamics, we attempt to elucidate the effect of loading frequency on the reversibility of cyclic deformation. We demonstrate that the HFT induces a higher fraction of reversible cyclic deformation because of a larger portion of elastic/anelastic deformation due to limited dislocation mobility, and a higher degree of reversibility in plastic deformation owing to the less occurrence of cross-slip.

Investigation Of Toppling Ball Flight In American Football With A Mechanical Field-Goal Kicker, Chase M Pfeifer, Timothy J. Gay, Jeff A. Hawks, Shane Farritor, Judith M. Burnfield

Department of Mechanical and Materials Engineering: Faculty Publications

A mechanical field-goal kicking machine was used to investigate toppling ball flight in American football place-kicking, eliminating a number of uncontrollable impact variables present with a human kicker. Ball flight trajectories were recorded using a triangulation-based projectile tracking system to account for the football’s 3-dimensional position during flight as well as initial launch conditions. The football flights were described using kinematic equations relating to projectile motion including stagnant air drag and were compared to measured trajectories as well as projectile motion equations that exclude stagnant air drag. Measured football flight range deviations from the non-drag equations of projectile motion corresponded …

Complementary Microscopy Techniques Applied For Characterizing The Localized Nanoscale Structure Of Poly (Vinylidene Fluoride), Wen Qian, Shuo Sun, Charles Nguyen, Wenlong Li, Stephen Ducharme, Joesph A. Turner

Department of Mechanical and Materials Engineering: Faculty Publications

Poly (vinylidenefluoride) (PVDF), a well-recognized electroactive polymer, has been studied extensively over many decades. Recently, there has been increasing interest in tuning the electrical properties of PVDF from ferroelectric to piezoelectric and to pyroelectric, which can be attained via controlling the microscale structure down to the nanoscale structure [1-2]. To optimize the preparation conditions of PVDF and its copolymers, as well as to improve the performance for many applications, comprehensive analytical techniques are of great importance. In this paper, we demonstrate complementary nanoscale characterization and measurement techniques, by conducting a systematic and coordinated study involving scanning electron microscopy (SEM), high …

Flow Patterns Through Vascular Graft Models With And Without Cuffs, Chia Min Leong, Gary B. Nackman, Timothy Wei

Department of Mechanical and Materials Engineering: Faculty Publications

The shape of a bypass graft plays an important role on its efficacy. Here, we investigated flow through two vascular graft designs±with and without cuff at the anastomosis. We conducted Digital Particle Image Velocimetry (DPIV) measurements to obtain the flow field information through these vascular grafts. Two pulsatile flow waveforms corresponding to cardiac cycles during the rest and the excitation states, with 10% and without retrograde flow out the proximal end of the native artery were examined. In the absence of retrograde flow, the straight end-to-side graft showed recirculation and stagnation regions that lasted throughout the full cardiac cycle with …

Dislocations Interaction Induced Structural Instability In Intermetallic Al2cu, Qing Zhou, Jian Wang, Amit Misra, Ping Huang, Fei Wang, Kewei Xu

Department of Mechanical and Materials Engineering: Faculty Publications

Intermetallic precipitates are widely used to tailor mechanical properties of structural alloys but are often destabilized during plastic deformation. Using atomistic simulations, we elucidate structural instability mechanisms of intermetallic precipitates associated with dislocation motion in a model system of Al₂Cu. Interaction of non-coplanar <001> dislocation dipoles during plastic deformation results in anomalous reactions—the creation of vacancies accompanied with climb and collective glide of <001> dislocation associated with the dislocation core change and atomic shuffle—accounting for structural instability in intermetallic Al₂Cu. This process is profound with decreasing separation of non-coplanar dislocations and increasing temperature and is likely to be …

Mechanical Performance Of Plla Stent, Longzhen Wang, Junfei Tong, Pengfei Dong, David L. Wilson, Hiram G. Bezerra, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Stent implantation is widely used to treat blocked lumen. Stents were meshed structure made of polymers and metal alloys, including stainless steel, cobalt chrome and nitinol [1]. Clinical studies had demonstrated that stents helped to scaffold the diseased lesion up to one year when tissue adapted to the stented environment [2]. However, the permanently implanted stents inside artery were associated with complications such as stent fracture, tissue inflammation, in-stent restenosis and thrombosis [3]. Currently, biodegradable stents are attracting more attention due to its potential long-term efficacy in treating blocked lumens. The detailed characterizations of biodegradable stents are essential for the …

Tissue Stresses In Stented Coronary Arteries With Different Geometries: Effect Of The Relation Between Stent Length And Lesion Length, Xiang Shen, Song Ji, Yong-Quan Deng, Hong-Fei Zhu, Jia-Bao Jiang, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

In-stent restenosis after stent deployment remains an obstruction in the long-term benefits of stenting. This study sought to investigate the influence of the relation between stent length and lesion length on the mechanics of the arterial wall with different geometries, including straight and tapered vessels. Results showed that when the length of the stent was longer than the lesion length, the maximum stress in plaque and vessel increased as the length of stent increased. When the length of the stent was shorter than the lesion length, the vessel stress induced by stent inflation was lower; both ends of the stenosis …

Scaffold Structural Microenvironmental Cues To Guide Tissue Regeneration In Bone Tissue Applications, Xuening Chen, Hongyuan Fan, Xiaowei Deng, Lina Wu, Tao Yi, Linxia Gu, Changchun Zhou, Yujiang Fan, Xingdong Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

In the process of bone regeneration, new bone formation is largely affected by physico-chemical cues in the surrounding microenvironment. Tissue cells reside in a complex scaffold physiological microenvironment. The scaffold should provide certain circumstance full of structural cues to enhance multipotent mesenchymal stem cell (MSC) differentiation, osteoblast growth, extracellular matrix (ECM) deposition, and subsequent new bone formation. This article reviewed advances in fabrication technology that enable the creation of biomaterials with well-defined pore structure and surface topography, which can be sensed by host tissue cells (esp., stem cells) and subsequently determine cell fates during differentiation. Three important cues, including scaffold …

Heat Transfer Across A Nanoscale Pressurized Air Gap And Its Application In Magnetic Recording, Jinglin Zheng, Yung-Kan Chen, Qin Zhou

Department of Mechanical and Materials Engineering: Faculty Publications

In this study, we investigated how a thermally actuated air bearing slider heats up a fast-spinning storage disk through a highly pressurized nanoscale air gap in a magnetic recording system. A Euleriandescription- based computational approach is developed considering heat conduction through a pressurized air film and near-field radiation across the gap. A set of field equations that govern the air bearing dynamics, slider thermo-mechanics and disk heat dissipation are solved simultaneously through an iterative approach. A temperature field on the same order as the hot slider surface itself is found to be established in the disk. The effective local heat …

Interfacial Characterization By Pull-Out Test Of Bamboo Fibers Embedded In Poly(Lactic Acid), Quentin Viel, Antonella Esposito, Jean-Marc Saiter, Carlo Santulli, Joseph A. Turner

Department of Mechanical and Materials Engineering: Faculty Publications

In this work, the apparent shear strength at the interface between a bamboo fiber and the surrounding poly(lactic acid) (PLA) matrix is quantified. A method for processing pull-out test samples within a controlled embedded length is proposed and the details of the test procedure are presented, along with a critical discussion of the results. Two series of samples are considered: untreated and mercerized bamboo fibers from the same batch, embedded in the same polyester matrix. Electron and optical microscopy are used to observe the fiber–matrix interface before and after the test, and to identify the failure mode of each sample, …

Synthesis Of Graphene And Graphene-Based Composite Membrane, Yuanjun Fan

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Vibration membrane equipped for earphone requires high performance in both mechanical properties and electronic properties. With extraordinary properties on both, graphene and graphene-based composite materials appear as a promising candidate for this application. Chemical vapor deposition (CVD) is believed to be the most convenient way to synthesize a large area (on scale of square centimeters) as well as a homogeneous thickness for the membrane. The thesis focuses on applying control variable experiment method to analyze different effects on mechanical property of the two CVD setting parameters: cooling rate, and hydrocarbon precursor. For isolating the specimens efficiently, a modified electrochemical method …

Method For Single Crystal Growth Of Photovoltaic Perovskite Material And Devices, Jinsong Huang, Qingfeng Dong

Department of Mechanical and Materials Engineering: Faculty Publications

Systems and methods for perovskite single crystal growth include using a low temperature solution process that employs a temperature gradient in a perovskite solution in a container , also including at least one small perovskite single crystal , and a substrate in the solution upon which substrate a perovskite crystal nucleates and grows , in part due to the temperature gradient in the solution and in part due to a temperature gradient in the substrate . For example , a top portion of the substrate external to the solution may be cooled .

Oct-Based Three Dimensional Modeling Of Stent Deployment, Pengfei Dong, David Prabhu, David L. Wilson, Hiram G. Bezerra, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Stent deployment has been widely used to treat narrowed coronary artery. Its acute outcome in terms of stent under expansion and malapposition depends on the extent and shape of calcifications. However, no clear understanding as to how to quantify or categorize the impact of calcification. We have conducted ex vivo stenting characterized by the optical coherence tomography (OCT). The goal of this work is to capture the ex vivo stent deployment and quantify the effect of calcium morphology on the stenting. A three dimensional model of calcified plaque was reconstructed from ex vivo OCT images. The crimping, balloon expansion and …

Multiple Scattering Theory For Polycrystalline Materials With Strong Grain Anisotropy: Theoretical Fundamentals And Applications, Huijing He

Department of Mechanical and Materials Engineering: Faculty Publications

This work is a natural extension of the author’s previous work: “Multiple scattering theory for heterogeneous elastic continua with strong property fluctuation: theoretical fundamentals and applications” (arXiv:1706.09137 [physics.geo-ph]), which established the foundation for developing multiple scattering model for heterogeneous elastic continua with either weak or strong fluctuations in mass density and elastic stiffness. Polycrystalline material is another type of heterogeneous materials that widely exists in nature and extensively used in industry. In this work, the corresponding multiple scattering theory for polycrystalline materials with randomly oriented anisotropic crystallites is developed. To validate the theory, the theoretical results for a series of …

Floating-Gate Transistor Photodetector, Jinsong Huang, Yongbo Yuan

Department of Mechanical and Materials Engineering: Faculty Publications

A field effect transistor photodetector that can operate in room temperature includes a source electrode , a drain electrode , a channel to allow an electric current to flow between the drain and source electrodes , and a gate electrode to receive a bias voltage for controlling the current in the channel . The photodetector includes a light - absorbing mate rial that absorbs light and traps electric charges . The light absorbing material is configured to generate one or more charges upon absorbing light having a wavelength within a specified range and to hold the one or more charges …

Software For Extracting Deformation Gradient And Stress From Md Simulations: Simulations Using The Charmm Force Field, Mehrdad Negahban, Lili Zhang, Zesheng Zhang, John Jasa, Antoine Jérusalem

Department of Mechanical and Materials Engineering: Faculty Publications

Software was developed, and is provided under a general use license, to calculate continuum level deformation gradient and stress for any group of atoms in an MD simulation that uses the Charmm force fields. This software can also calculate the interaction stress applied by one group of atoms on any other group. To obtain deformation gradient and stress, the user needs to provide the selected group(s) of atoms in an atom group identification file, and provide the associated LAMMPS format files and force field parameter file. An example is included to demonstrate the use of the software.

Energy Absorbing Guardrail System, John R. Rohde, John D. Reid, King K. Mak, Dean L. Sicking

Department of Mechanical and Materials Engineering: Faculty Publications

A highway crash attenuation system having W - beam rail elements attached to a plurality of vertical posts . An impact terminal with a feeder chute guides one or more of the W - beam rail elements through the impact terminal . The feeder chute has an impact shield extending along a traffic facing side of the chute from an upstream - most end to a downstream - most end of the chute closing the traffic - facing side of the chute . The system also has an anchor cable release mechanism for releasing the cable downstream of the first …

Shape-Adaptive Mechanism For Robotic Grasping, Carl A. Nelson

Department of Mechanical and Materials Engineering: Faculty Publications

A grapser can include a first pantograph cell and a second pantograph cell coupled with the first pantogrpah cell. The first and second pantograph cells can be coupled together at a first pivot and a second pivot. The grasper can also include a finger extendable in a direction extending between the first pivot and the second pivot. The grasper can include a support base, where one or more links of the first pantograph cell can be slidably coupled with the support base for extending the grasper. In some embodiment, the grasper can be configured to extend along a curved path. …

Development Of The End-Effector Of A Cable-Driven Parallel Manipulator For Automated Crop Sensing, Iman Salafian

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

A four cable-driven parallel manipulator (4CDPM), consisting of sophisticated spectrometers and imagers, is under development for use in acquiring phenotypic and environmental data over an acre-sized maize field. This thesis presents the design, controls, and testing of two sub-systems in a 4CDPM: a Center of Mass Balance System (CMBS) and a Drop-Down System (DDS).

One of the factors that influences stability is the center of mass (COM) position of the end effector. An offset in COM can cause a pendulum effect or an undesired tilt angle. A center of mass balancing system is presented in this thesis to minimize the …

Hyperelastic Structural Fuses For Improved Earthquake Resilience Of Steel Concentrically-Braced Buildings, Francys López-Mosquera

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Improving structural resilience (i.e., reducing service interruptions and improving rapidity of function restoration) following extreme events is one of the primary contemporary challenges in structural engineering. While massive casualties have successfully been avoided through the adoption of modern building codes, the sole codified performance objective has been limited to the life safety/collapse prevention range of response. Christchurch, NZ, highlighted the insufficiency of this approach, with large sections of the city nonfunctional after a major earthquake, and with subsequent collapses induced by significant aftershocks. Engineering advances to improve building and community resilience are necessary to mitigate hazards from becoming disasters. This …

Meniscus-Assisted Solution Printing Of Largegrained Perovskite Films For High-Efficiency Solar Cells, Ming He, Bo Li, Xun Cui, Beibei Jiang, Yanjie He, Yihuang Chen, Daniel O'Neil, Paul Szymanski, Mostafa A. El-Sayed, Jinsong Huang, Zhiqun Lin

Department of Mechanical and Materials Engineering: Faculty Publications

Control over morphology and crystallinity of metal halide perovskite films is of key importance to enable high-performance optoelectronics. However, this remains particularly challenging for solution-printed devices due to the complex crystallization kinetics of semiconductor materials within dynamic flow of inks. Here we report a simple yet effective meniscus-assisted solution printing (MASP) strategy to yield large-grained dense perovskite film with good crystallization and preferred orientation. Intriguingly, the outward convective flow triggered by fast solvent evaporation at the edge of the meniscus ink imparts the transport of perovskite solutes, thus facilitating the growth of micrometre-scale perovskite grains. The growth kinetics of perovskite …

Dissipative Elastic Metamaterial With A Lowfrequency Passband, Yongquan Liu, Jianlin Yi, Zheng Li, Xianyue Su, Wenlong Li, Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

We design and experimentally demonstrate a dissipative elastic metamaterial structure that functions as a bandpass filter with a low-frequency passband. The mechanism of dissipation in this structure is well described by a mass-spring-damper model that reveals that the imaginary part of the wavenumber is non-zero, even in the passband of dissipative metamaterials. This indicates that transmittance in this range can be low. A prototype for this viscoelastic metamaterial model is fabricated by 3D printing techniques using soft and hard acrylics as constituent materials. The transmittance of the printed metamaterial is measured and shows good agreement with theoretical predictions, demonstrating its …

Multiple Scattering Theory For Heterogeneous Elastic Continua With Strong Property Fluctuation: Theoretical Fundamentals And Applications, Huijing He

Department of Mechanical and Materials Engineering: Faculty Publications

Scattering of elastic waves in heterogeneous media has become one of the most important problems in the field of wave propagation due to its broad applications in seismology, natural resource exploration, ultrasonic nondestructive evaluation and biomedical ultrasound. Nevertheless, it is one of the most challenging problems because of the complicated medium inhomogeneity and the complexity of the elastodynamic equations. A widely accepted model for the propagation and scattering of elastic waves, which properly incorporates the multiple scattering phenomenon and the statistical information of the inhomogeneities is still missing. In this work, the author developed a multiple scattering model for heterogeneous …

A Strategy To Optimize Recovery In Orthopedic Sports Injuries, Michael P. Sealy, Ziye Liu, Chao Li, Yuebin Guo, Ben White, Mark Barkey, Brian Jordon J, Luke N. Brewer, Dale Feldman

Department of Mechanical and Materials Engineering: Faculty Publications

An important goal for treatment of sports injuries is to have as short a recovery time as possible. The critical problem with current orthopedic implants is that they are designed to be permanent and have a high complication rate (15%) that often requires removal and replacement with a second surgery; and subsequently a second rehabilitation cycle. This study was designed to test the feasibility of having a device that could provide the needed mechanical properties, while promoting healing, for a specified amount of time and then degrade away, to shorten the recovery time. The specific strategy was to create a …