Engineering Education Commons^™

Introducing The Engineering Technology Programs To All Incoming Freshmen Engineering And Technology Students–The Result Is Better For All, Gary Crossman, Anthony Dean

Engineering Technology Faculty Publications

The Department of Engineering Technology at Old Dominion University participates in a freshman engineering course sequence, along with four engineering departments in the Batten College of Engineering and Technology. The two course sequence, Exploring Engineering and Technology I and II, involve the five departments in teaching at least one five week module in each of the two courses. Each department generally involves the students in a basic design project related to its discipline. Since the Department of Engineering Technology has three main programs – Civil, Electrical, and Mechanical – it has elected to divide its five week segment into three …

An Assessment And Continuous Improvement Model For Engineering Technology Programs, Alok Verma, Gary Crossman

Engineering Technology Faculty Publications

Assessment and continuous improvement are essential and critical processes for higher education. Development and implementation of such processes are not only required by the Accreditation Board for Engineering and Technology (ABET) but it is also a necessary condition for the maturation and development of any engineering technology program. The assessment and continuous improvement plan discussed here was developed at Old Dominion University (ODU) and implemented during the last accreditation cycle within the Engineering Technology Department. The plan is based on two cycles of assessment and evaluation, a short cycle of one year and a long term cycle of three years. …

Designing A Microcontroller Training Platform For Active Distance Learning Engineering And Technology Students, Steve C. Hsiung, James E. Eiland, John R. Hackworth, John Ritz

Engineering Technology Faculty Publications

This is an active distance-learning project that addresses the hands-on microprocessor/ mi-crocontroller-related courses. A research team designed a low-cost training system with supporting instructional materials to assist the teaching of these concepts. Individual laboratory activities are being developed to reinforce student learning and skill development in programming concepts. This basic system format eventually will support an array of engineering and technology courses. This project involves two community colleges, Blue Ridge Community College (BRCC) and Olympic College (OC), and a four-year university, Old Dominion University (ODU), in a collaborative research team to design and develop a specific PIC microcontroller training system …

A New Approach In Microprocessor/Microcontroller Courses/Laboratories Material Design And Development, Steve C. Hsiung, Jeff Willis

Engineering Technology Faculty Publications

Courses in microprocessors and microcontrollers are standard parts of the Engineering Technology core curricula. The traditional course material developments include both lectures and associated laboratory exercises. No matter how creative is the curriculum; it is usually budgetary constraints that confine the creativity when developing new curricula. This limits the freedom of the major approach in new course development.

This article demonstrates new course lecture and laboratories material development that starts from ground up with both a hardware platform and simulation software design for microprocessor/microcontroller related courses. It is not only very cost effective, but also does not limit the instructor's …

A Comparison Between Frequent Out-Of-Class Assignments And Frequent In-Class Assessments Relative To Student Performance In A Sophomore Level Electrical Circuit Analysis Course, Isaac Flory, Christian Hearn

Engineering Technology Faculty Publications

Two parallel sections of a sophomore level circuit analysis course in Electrical Engineering Technology were structured to provide insight to the marginal utility of out-of-class assignments versus in-class assessments in academic performance. Student distributions for each section, the classroom model, the composition of the common tests and exam, and grading formats are discussed. The data presented and the conditions of the resulting observations indicate the model which favored out-of-class assignments led to improved test scores.

A Hybrid Course In Fundamentals Of Building Construction Using Combination Archived Video And Live Session Distance Learning, Vernon W. Lewis Jr., Carol L. Considine, June Ritchie

Engineering Technology Faculty Publications

A course in the Fundamentals of Building Construction has been a curricular requirement of the Civil Engineering Technology Program (CET) since its inception. This course was taught traditionally as an on-campus class. Over the last ten years, the CET program has expanded to contain an extensive distance learning component, with at least half of the enrollment located off campus. The model for the typical distance-learning class is to meet for three hours, once a week, with a fully interactive (voice) live class. In consideration of the demand of a growing distance learning system, it was decided to restructure this class …

Teaching Lean Manufacturing Concepts Using Physical Simulations Within Engineering Technology Program, Alok Verma

Engineering Technology Faculty Publications

Physical Simulations have a proven record as a teaching tool. Concepts that are often hard to grasp are made easy by the use of physical simulation activities. The constructivism learning theory suggests that people learn better by actively participating in the process of learning. Effectiveness of simulation-based learning is well recognized. According to the Encyclopedia of Educational Technology, "Simulation-based learning involves the placement of a student into a realistic scenario or situation. The student is then responsible for any changes that occur as a result of their decisions." The computer integrated manufacturing course in the mechanical engineering technology program was …

Developing A New Program In Marine Engineering Technology, Anthony Dean, Gary Crossman, Alok Verma

Engineering Technology Faculty Publications

The Department of Engineering Technology, in the Batten College of Engineering and Technology at Old Dominion University, in conjunction with members of its advisory board and other industry representatives have begun a sustained effort to promote and develop a strong course of study in Marine Engineering Technology. Located in Norfolk, Virginia, Old Dominion University, and particularly the Department of Engineering Technology, is uniquely positioned to develop such a program. With strong ties to the world's largest Naval Base and superlative shipbuilding, maintenance and repair facilities, early qualitative research indicated high interest for development of such a program in support of …