Open Access. Powered by Scholars. Published by Universities.®
- Institution
- Keyword
-
- Allergy (1)
- Anaphylaxis (1)
- Ankle joint (1)
- Auto-injector (1)
- Basquin's Equation (1)
-
- Bicuspid valve (1)
- Cancer (1)
- Capsule pump (1)
- Coffin-Manson Equation (1)
- Cytotoxic assay (1)
- Drug delivery (1)
- Fatigue testing standards (1)
- Gait (1)
- High strain rate testing (1)
- High throughput (1)
- High-cycle fatigue (1)
- Internet of Things (1)
- Internet-of-things (1)
- Low-cycle fatigue (1)
- Mechanical testing (1)
- Metamaterial (1)
- Metasurface antenna (1)
- Microfluidics (1)
- Micropump (1)
- Optofluidics (1)
- Polymer (1)
- Polymer model (1)
- Reconfigurable (1)
- Remote (1)
- Shape memory alloy (1)
Articles 1 - 5 of 5
Full-Text Articles in Signal Processing
Shape Memory Alloy Capsule Micropump For Drug Delivery Applications, Youssef Mohamed Kotb
Shape Memory Alloy Capsule Micropump For Drug Delivery Applications, Youssef Mohamed Kotb
Theses and Dissertations
Implantable drug delivery devices have many benefits over traditional drug administration techniques and have attracted a lot of attention in recent years. By delivering the medication directly to the tissue, they enable the use of larger localized concentrations, enhancing the efficacy of the treatment. Passive-release drug delivery systems, one of the various ways to provide medication, are great inventions. However, they cannot dispense the medication on demand since they are nonprogrammable. Therefore, active actuators are more advantageous in delivery applications. Smart material actuators, however, have greatly increased in popularity for manufacturing wearable and implantable micropumps due to their high energy …
Challenges And Signal Processing Of High Strain Rate Mechanical Testing, Barae Lamdini
Challenges And Signal Processing Of High Strain Rate Mechanical Testing, Barae Lamdini
Theses and Dissertations
Dynamic testing provides valuable insight into the behavior of materials undergoing fast deformation. During Split-Hopkinson Pressure Bar testing, stress waves are measured using strain gauges as voltage variations that are usually very small. Therefore, an amplifier is required to amplify the data and analyze it. One of the few available amplifiers designed for this purpose is provided by Vishay Micro-Measurements which limits the user’s options when it comes to research or industry. Among the challenges of implementing the Hopkinson technology in the industry are the size and cost of the amplifier. In this work, we propose a novel design of …
Electromechanical Fatigue Properties Of Dielectric Elastomer Stretch Sensors Under Orthopaedic Loading Conditions, Andrea Karen Persons
Electromechanical Fatigue Properties Of Dielectric Elastomer Stretch Sensors Under Orthopaedic Loading Conditions, Andrea Karen Persons
Theses and Dissertations
Fatigue testing of stretch sensors often focuses on high amplitude, low-cycle fatigue (LCF) behavior; however, when used for orthopaedic, athletic, or ergonomic assessments, stretch sensors are subjected to low amplitude, high-cycle fatigue (HCF) conditions. As an added layer of complexity, the fatigue testing of stretch sensors is not only focused on the life of the material comprising the sensor, but also on the reliability of the signal produced during the extension and relaxation of the sensor. Research into the development of a smart sock that can be used to measure the range of motion (ROM) of the ankle joint during …
Design And Fabrication Of Zinc Oxide Optofluidic Laser Elements, Kyle T. Bodily
Design And Fabrication Of Zinc Oxide Optofluidic Laser Elements, Kyle T. Bodily
Theses and Dissertations
This thesis systematically goes through the derivation, simulation, and experimentation of Zinc Oxide optofluidic micro laser elements. Single and coupled ring resonators were simulated to show single mode transmission as well as enhanced coupling capabilities when surrounded by high refractive index liquid. Devices with diameters ranging from 100-500 µm were successfully fabricated inexpensively through standard cleanroom procedures. The devices were tested using two different pump laser systems. Testing included such factors as high pump intensity, various angles of excitation, and low temperature. In all cases PL emission was observed and recorded.
Wideband Metasurface Antenna, Thomas A. Lepley
Wideband Metasurface Antenna, Thomas A. Lepley
Theses and Dissertations
This effort explored design of metasurface antennas and evaluated their suitability for ultra-wideband applications (2 to 18 GHz). Six unit cell types were characterized. Eigenmode simulations produced frequency vs. phase data for the unit cells, from which impedance vs. gap size data was computed. A holographic design equation was used to generate the metasurface antenna designs. The unit cell simulations revealed that the assumption of single mode operation is a constraint for wideband designs. An 8" by 8" metasurface antenna with a Rogers 3010 dielectric and a design frequency of 10 GHz was fabricated and tested. It had a 1.5:1 …