Electronic Devices and Semiconductor Manufacturing Commons^™

Reducing The Production Cost Of Semiconductor Chips Using (Parallel And Concurrent) Testing And Real-Time Monitoring, Qutaiba Khasawneh

Electrical Engineering Theses and Dissertations

Consumer electronics changed the semiconductor industry by developing many new challenges for consumer products. One of the main challenges in the consumer product is that it propelled the volume of production to massive production, e.g. hundreds of millions of cell phones are produced yearly. Combined with the overproduction of consumer products, price pressure is another challenge for consumer products. Many of the new techniques used in the design and fabrication enabled the integration of more devices in the same chips. This reduced the cost of the chips, lowered the power consumption, increased the circuit operation speed, enabled more reliable implementation, …

Design And Optimization Of A High Power Density Silicon Carbide Traction Inverter, Tyler Adamson

Graduate Theses and Dissertations

This project was initiated with the goal of demonstrating a 3-phase silicon carbide based 150-kW 25 kW/L DC-AC power conversion unit capable of operation with coolant temperatures up to 90°C. The project goals were met and exceeded by first analyzing the established inverter topologies to find which one would yield the highest power density while still meeting electrical performance needs in the 150-kW range. Following topology selection, the smallest silicon carbide power module that met the electrical requirements of the system was found through experimental testing and simulation. After a power module selection was finalized, a DC link capacitor bank …

Development Of A Comsol Microdialysis Model, Towards Creation Of Microdialysis On A Chip With Improved Geometries And Recovery, Patrick Pysz

Graduate Theses and Dissertations

Microdialysis (µD) sampling is a diffusion-limited sampling method that has been widely used in different biomedical fields for greater than 35 years. Device calibration for in vivo studies is difficult for current non-steady state analytes of interest correlated with both inflammatory response and microbial signaling molecules (QS); which exist in low ng/mL to pg/mL with molecular weights over a wide range of 170 Da to 70 kDa. The primary performance metric, relative recovery (RR), relating the collected sample to the extracellular space concentration varies from 10% to 60% per analyte even under controlled bench-top conditions. Innovations in microdialysis device design …

Interfacial Contact With Noble Metal - Noble Metal And Noble Metal - 2d Semiconductor Nanostructures Enhance Optical Activity, Ricardo Raphael Lopez Romo

Graduate Theses and Dissertations

Noble metal nanoparticles and two-dimensional (2D) transition metal dichalcogenide (TMD) crystals offer unique optical and electronic properties that include strong exciton binding, spin-orbital coupling, and localized surface plasmon resonance. Controlling these properties at high spatiotemporal resolution can support emerging optoelectronic coupling and enhanced optical features. Excitation dynamics of these optical properties on physicochemically bonded mono- and few-layer TMD crystals with metal nanocrystals and two overlapping spherical metal nanocrystals were examined by concurrently (i) DDA simulations and (ii) far-field optical transmission UV-vis spectroscopic measurements. Initially, a novel and scalable method to unsettle van der Waals bonds in bulk TMDs to prepare …

High Frequency Ltcc Based Planar Transformer, Adithya Venkatanarayanan

Graduate Theses and Dissertations

As we move towards high power and higher frequency related technology, conventional wire-wound magnetics have their own limitations which has led path to the development of planar based magnetic materials. Nowadays more planar magnetic technology has been employed because it is easier to fabricate them. The planar magnetic is a transformer or an inductor that replaces the wire-wound transformer or inductors which generally uses copper wires. One of the main reasons why we move to planar magnetic technology is its operation at higher frequency which provides higher power density. This study explains in detail about the design and fabrication of …

Optical Angular Scatterometry: In-Line Approach For Roll-2-Roll And Nano-Imprint Fabrication Systems, Juan Jose Faria-Briceno

Electrical and Computer Engineering ETDs

As critical dimensions continue to shrink and structures become more complex, metrology processes are challenging to implement during in-line nanomanufacturing. Non-destructive, non-contact, and high-speed conditions are required to achieve proper metrology processes during in-line manufacturing. Optical scatterometry is a nanoscale metrology tool widely used in integrated circuit manufacturing for characterization and quality control. However, most applications of optical scatterometry operate off-line. A high-speed, in-line, non-contact, non-destructive scatterometry angular system has been demonstrated in this work to scan pattern surfaces during real-time nano-fabrication.

Our system has demonstrated scanning capabilities using flat, 1D and 2D complex structures. The flat surface samples consist …

Integrated Chirped-Grating Spectrometer-On-A-Chip, Shima Nezhadbadeh

Optical Science and Engineering ETDs

In this dissertation we demonstrate a new structure based on waveguide coupling atop a silicon wafer using a chirped grating to provide the dispersion that leads to a high-resolution, compact, fully integrable and CMOS-compatible spectrometer. Light is both analyzed and detected in a single, completely monolithic component which enables realizing a high-resolution portable spectrometer with an extremely compact footprint. The structure is comprised of a SiO₂/Si₃N₄/SiO₂ waveguide on top of a silicon wafer. Grating regions are fabricated on the top cladding of the waveguide. The input light is incident on a chirped grating …

Diseño E Implementación De Un Sistema Automático De Fertiirrigación Para Un Cultivo De Gulupa, Lisbey Catherine Gómez Puentes, Sebastian Ilich Jimenez Vivas

Ingeniería en Automatización

En Colombia la producción frutícola se ha tecnificado notablemente en los últimos años debido a la creciente demanda nacional e internacional de frutas tropicales; la gulupa fue la segunda fruta exótica con más exportación en el año 2017 (La vanguardia, 2018). Actualmente en el municipio de La Belleza Santander los sistemas de riego y fertilización para el cultivo de gulupa son trabajos manuales, ocasionando anormalidades en los frutos ya que por este motivo el fruto puede quedar rugoso, con pulpa seca, insípida y poco aromática; además, se puede presentar desorden fisiológico en la planta (crecimiento y vigor). Al ser este …

Desarrollo De Un Juguete Educativo Armable, Que Permita El Aprendizaje Correcto Del Cepillado Dental, Jhon Alejandro Celis Méndez, Luis Arturo Penagos Gómez

Ingeniería en Automatización

El presente documento se constituye como la memoria técnica y a su vez la guía para el entendimiento del prototipo denominado por los autores como “ODONTODRILO”, el cual surge a partir del proyecto titulado “Desarrollo de un juguete educativo armable, que permita el aprendizaje correcto del cepillado dental”. En este sentido, se tiene que el proyecto consistió en diseñar, fabricar e implementar un juguete educativo armable, que permita el aprendizaje correcto del cepillado dental en niños de temprana edad. A partir de la necesidad citada, se definió un marco metodológico que consiste en tres etapas, la primera de ellas se …

Design And Analysis Of Modular Axial Flux Switched Reluctance Motor, Rochak Shiwakoti

University of New Orleans Theses and Dissertations

This thesis presents a new modular structure of the axial flux Switched Reluctance Motor (SRM). The design consists of four stator disks with each adjacent disk rotated 30 degrees apart and four rotor disks connected to a common shaft. The proposed design aims to reduce the unwanted radial force, mitigate the torque ripple, and improve the efficiency. The modular structure distributes the radial force and torque strokes along the axial length of the motor, potentially damping the torque pulsation. In addition, the modular structure would deliver the rating power at a lower current level, reducing the overall ohmic loss. Moreover, …

Switching Trajectory Control For High Voltage Silicon Carbide Power Devices With Novel Active Gate Drivers, Shuang Zhao

Graduate Theses and Dissertations

The penetration of silicon carbide (SiC) semiconductor devices is increasing in the power industry due to their lower parasitics, higher blocking voltage, and higher thermal conductivity over their silicon (Si) counterparts. Applications of high voltage SiC power devices, generally 10 kV or higher, can significantly reduce the amount of the cascaded levels of converters in the distributed system, simplify the system by reducing the number of the semiconductor devices, and increase the system reliability.

However, the gate drivers for high voltage SiC devices are not available on the market. Also, the characteristics of the third generation 10 kV SiC MOSFETs …

Five-Level Flying Capacitor Converter Used As A Static Compensator For Current Unbalances In Three-Phase Distribution Systems, Rafael Franceschi

Graduate Theses and Dissertations

This thesis presents and evaluates a solution for unbalanced current loading in three-phase distribution systems. The proposed solution uses the flying capacitor multilevel converter as its main topology for an application known as Unbalanced Current Static Compensator. The fundamental theory, controller design and prototype construction will be presented along with the experimental results. The Unbalanced Current Static Compensator main objective is the balancing of the up-stream currents from the installation point to eliminate the negative- and zero-sequence currents originated by unbalanced single-phase loads.

Three separate single-phase flying capacitor converters are controlled independently using a d-q rotating reference frame algorithm to …

Pixelated Gasb Membranes For Photovoltaics: Fabrication And Structure-Property Relationships, Vijay Saradhi Mangu

Electrical and Computer Engineering ETDs

In this thesis, I present a reliable and efficient approach to heterogeneous integration of single-crystalline GaSb semiconductors with highly mismatched materials. The mismatch may refer to the crystalline structure and the thermal expansion coefficient of single-crystalline GaSb and the other materials of interest. The strategy of hetero-integration relies on epitaxial lift-off. This approach prevents the formation of extended structural defects that are detrimental to the performance of optoelectronic devices and preserves GaSb growth substrates for potential reuse.

Within my research work, I have overcome some outstanding challenges of epitaxial lift-off of GaSb, and I have demonstrated the operation of single-crystalline …

Structural Health Monitoring Of Composite Parts: A Review, Jacob Pessin

Honors Theses

Structural health monitoring has the potential to allow composite structures to be more reliable and safer, then by using more traditional damage assessment techniques. Structural health monitoring (SHM) utilizes individual sensor units that are placed throughout the load bearing sections of a structure and gather data that is used for stress analysis and damage detection. Statistical time based algorithms are used to analyze collected data and determine both damage size and probable location from within the structure. While traditional calculations and life span analysis can be done for structures made of isotropic materials such as steel or other metals, composites …

Dc-Dc Converter For Electric Vehicle, Jason Y. Zhou, Nicholas James Mah

Electrical Engineering

In this work, a DC-DC converter is designed for an electric vehicle. The DC-DC converter is designed to provide 500W with a 200-400V input and a 12-15V adjustable output. Electric vehicle sales are beginning to increase in popularity and the need for DC-DC converters to siphon power from the tractive system is not yet fully satisfied, especially for single-seater class vehicles. Additionally, improving performance in efficiency without sacrificing wide input voltage range can benefit future DC-DC converter designs. In the end, a forward active clamp DC-DC converter is designed and tested. Additionally, spreadsheet calculators, LTSpice simulations, and Matlab scripts were …

Designing A Low-Cost Ultrasound Pulser, Andrea Huey

Honors Theses

Ultrasound imaging allows for those studying living beings to see inside a subject without causing it harm. This allows for real-time images to be taken, leading to ease of observational research. However, while this technology is beneficial to those who utilize it, the devices used to create and receive ultrasound pulses can be incredibly complex, allowing for precise adjustment of the output signal and various other functions, and therefore expensive. The focus of this senior project is the design of a low-cost pulser for use with an ultrasound transducer. While it does not have all the high-level functions of the …

Symmetry And Dopant Diffusion In Inverted Nanopyramid Arrays For Thin Crystalline Silicon Solar Cells, Seok Jun Han

Chemical and Biological Engineering ETDs

In this dissertation, we enhance the efficiency of thin flexible monocrystalline silicon solar cells by breaking symmetry in light trapping nanostructures and improving homogeneity in dopant concentration profile. These thin cells are potentially less expensive than conventional thick silicon cells by using less silicon material and making the cells more convenient to be handled when supported on polymer films. Moreover, these cells are widely applicable due to their flexibility and lightweight. However, for high efficiencies, these cells require effective light trapping and charge collection. We achieve these in cells based on 14-mm-thick free-standing silicon films with light-trapping arrays of nanopyramidal …

Algorithmic Multi-Color Cmos Avalanche Photodiodes For Smart-Lighting Applications, Md Mottaleb Hossain

Optical Science and Engineering ETDs

Future smart-lighting systems are expected to deliver adaptively color-tunable and high-quality lighting that is energy efficient while also offering integrated visible-light wireless communication services. To enable these systems at a commercial level, inexpensive and fast sensors with spectral-sensing capability are required. CMOS-compatible silicon avalanche photodiodes (APDs) can be an excellent fit to this problem due to their excellent sensitivity, high speeds and cost effectiveness; however, color sensing is a challenge without resorting to expensive spectral filters, as done in commercially. To address this challenge, we have recently designed and modeled a novel CMOS-compatible dual-junction APD. The device outputs two photocurrents …

Prototyping A Capacitive Sensing Device For Gesture Recognition, Chenglong Lin

Computer Science and Computer Engineering Undergraduate Honors Theses

Capacitive sensing is a technology that can detect proximity and touch. It can also be utilized to measure position and acceleration of gesture motions. This technology has many applications, such as replacing mechanical buttons in a gaming device interface, detecting respiration rate without direct contact with the skin, and providing gesture sensing capability for rehabilitation devices. In this thesis, an approach to prototype a capacitive gesture sensing device using the Eagle PCB design software is demonstrated. In addition, this paper tested and evaluated the resulting prototype device, validating the effectiveness of the approach.

Characterization Of High Temperature Optocoupler For Power Electronic Systems, David Gonzalez

Electrical Engineering Undergraduate Honors Theses

High-temperature devices have been rapidly increas due to the implementation of new technologies like silicon carbide, high-temperature ceramic, and others. Functionality under elevated temperatures can reduce signal integrity reducing the reliability of power electronic systems. This study presents an ongoing research effort to develop a high-temperature package for optocouplers to operate at higher temperature compared with commercial devices. Low temperature co-fired ceramic (LTCC) was used as the substrate. Bare die commercial LED and photodetectors were attached to the substrate and tested for functionality. Preliminary results show enhanced performance at elevated temperatures compared to a commercial optocoupler device.

Synchrophasor-Based Fault Location Detection And Classification, In Power Systems, Using Artificial Intelligence, Hemal Falak

Graduate Theses and Dissertations

With the introduction of sophisticated electronic gadgets which cannot sustain interruption in the provision of electricity, the need to supply uninterrupted and reliable power supply, to the consumers, has become a crucial factor in the present-day world. Therefore, it is customary to correctly identify fault locations in an electrical power network, in order to rectify faults and restore power supply in the minimum possible time. Many automated fault location detection algorithms have been proposed, however, prior art requires topological and physical information of the electrical power network. This thesis presents a new method of detecting fault locations, in transmission as …

Investigation Of Critical Technologies Of Chemical Vapor Deposition For Advanced (Si)Gesn Materials, Joshua Matthew Grant

Graduate Theses and Dissertations

The development of new materials for efficient optoelectronic devices from Group IV elements is the heart of Group IV photonics. This has direct ties to modern technology as the foundation for the electronics industry is silicon. This has driven the development of silicon-based optoelectronics using these other Group IV materials as silicon is a poor optical material due to its indirect band gap when compared to the III-V semiconductors that are used by most of the optoelectronics industry. While efforts have been made to integrate III-V materials onto silicon substrates, the incompatibility with the complementary metal oxide semiconductor process has …

A Silicon Germanium Cmos Linear Voltage Regulator For Wireless Agricultural Applications, Aminta Naidili Castillo Robles

Graduate Theses and Dissertations

This thesis presents the design, simulation and test results of a silicon germanium (SiGe) complementary metal-oxide-semiconductor (CMOS) linear regulator. The objective of the circuit is to power other analog devices regardless of the load current and input voltage changes. The application of this regulator is to be part of a project developing a miniaturized semiconductor platform that can be inserted into stems of crops in order to measure data inside the plant and then send it wirelessly to the user. The linear regulator was designed on a BiCMOS SiGe 0.13µm which is a GlobalFoundries process. It has been tested at …

Model Development And Assessment Of The Gate Network In A High-Performance Sic Power Module, William Austin Curbow

Graduate Theses and Dissertations

The main objective of this effort is to determine points of weakness in the gate network of a high-performance SiC power module and to offer remedies to these issues to increase the overall performance, robustness, and reliability of the technology. In order to accomplish this goal, a highly accurate model of the gate network is developed through three methods of parameter extraction: calculation, simulation, and measurement. A SPICE model of the gate network is developed to analyze four electrical issues in a high-speed, SiC-based power module including the necessary internal gate resistance for damping under-voltage and over-voltage transients, the disparity …

Bgaas Alloy Semiconductors For Lasers On Silicon, Joshua Mcarthur

Mechanical Engineering Undergraduate Honors Theses

In the world of semiconductors today, there is a large dissonance between optical devices and electrical application. Due to the limitations of electron transport, photonic integrated circuits are soon-to-be vital in fields like telecommunications and sensing. Right now, these PIC’s are mostly made from indium phosphide. Due to its ubiquitous nature, however, there is a huge push to integrate efficient optics with silicon. It’s cheap, abundant, dope-able, and our electronic infrastructure is based on it. The reason why silicon photonics aren’t already commercialized is because of silicon’s indirect bandgap—it is inefficient with optical applications. The problem with combining direct gap …

Direct Printing Of Conductive Inks For Organic Electronics And Wearable Microfluidics, Aditi Naik

Doctoral Dissertations

This dissertation examines the direct printing of conductive inks on polymeric substrates for applications in organic electronics, microfluidic valving systems, and wearable sweat sensors. The inexpensive production of solution-based electrodes with high electrical conductivity is necessary to enable the next-generation of printed, flexible, and organic electronics. Specifically, the optimization and printing of liquid-phase graphene ink and nanoparticle-based silver ink by soft nanoimprint lithography and inkjet-printing is discussed to achieve printed functional devices. Using scalable low-cost patterning systems, these flexible applications are compatible with roll-to-roll processing, enabling large-scale manufacturing. This research expands the knowledge of high-resolution printing optimization for the direct …

Energy Efficiency Of Computation In All-Spin Logic: Projections And Fundamental Limits, Zongya Chen

Masters Theses

Built with nanomagnets, a spintronic device called the all-spin logic (ASL) device carries information with only spin currents, resulting in a low power supply--10 mV. This voltage is 100 times smaller than the conventional CMOS devices (usually 0.8~1V). The potential for improved energy efficiency made possible by the low operating voltage of ASL makes it one of the most promising devices among its post-CMOS competitors.

The basic working principles of ASL device are introduced in this thesis and two complementary approaches to studying energy efficiency of computation are applied to a common set of ASL circuits: (1) a circuit simulation …

Experimental Study And Modeling Of The Gm-I Dependence Of Long-Channel Mosfets, Michael Fong Cheng

Master's Theses

This thesis describes an experimental study and modeling of the current-transconductance dependence of the ALD1106, ALD1107, and CD4007 arrays. The study tests the hypothesis that the I-gm dependence of these 7.8 µm to 10 µm MOSFETs conforms to the Advanced Compact Model (ACM). Results from performed measurements, however, do not support this expectation. Despite the relatively large length, both ALD1106 and ALD1107 show sufficiently pronounced ‘short-channel’ effects to render the ACM inadequate. As a byproduct of this effort, we confirmed the modified ACM equation. With an m factor of approximately 0.6, it captures the I-gm dependence with sub-28% maximum error …

Investigation Of Radiation-Hardened Design Of Electronic Systems With Applications To Post-Accident Monitoring For Nuclear Power Plants, Qiang Huang

Electronic Thesis and Dissertation Repository

This research aims at improving the robustness of electronic systems used-in high level radiation environments by combining with radiation-hardened (rad-hardened) design and fault-tolerant techniques based on commercial off-the-shelf (COTS) components. A specific of the research is to use such systems for wireless post-accident monitoring in nuclear power plants (NPPs). More specifically, the following methods and systems are developed and investigated to accomplish expected research objectives: analysis of radiation responses, design of a radiation-tolerant system, implementation of a wireless post-accident monitoring system for NPPs, performance evaluation without repeat physical tests, and experimental validation in a radiation environment.

A method is developed …

Herramienta Computacional Para La Organización Y Presentación De Datos De Descargas Atmosféricas En Circuitos Eléctricos Aéreos De Media Tensión, Diego Alejandro González Lizcano

Ingeniería Eléctrica

El territorio colombiano presenta una de las más altas actividades atmosféricas del planeta. Esto según estudios de niveles isoceráunicos realizados en todo el mundo (Torres & Ávila, 2000). Entregando retos de confiabilidad para sistemas de transmisión y distribución eléctrica, puesto que, para estos sistemas el factor de mayor incidencia en el incremento de la discontinuidad del suministro son las descargas atmosféricas. Además, las incidencias sobre las líneas aéreas o en cercanía de estas, generan flameos en los aisladores, deteriorando la confiabilidad del sistema si no se realizan maniobras de mantenimiento preventivo. Ceñido a nuevos avances tecnológicos en la localización y …