Electronic Devices and Semiconductor Manufacturing Commons^™

Model-Based Design Of An Optimal Lqg Regulator For A Piezoelectric Actuated Smart Structure Using A High-Precision Laser Interferometry Measurement System, Grant P. Gallagher

Master's Theses

Smart structure control systems commonly use piezoceramic sensors or accelerometers as vibration measurement devices. These measurement devices often produce noisy and/or low-precision signals, which makes it difficult to measure small-amplitude vibrations. Laser interferometry devices pose as an alternative high-precision position measurement method, capable of nanometer-scale resolution. The aim of this research is to utilize a model-based design approach to develop and implement a real-time Linear Quadratic Gaussian (LQG) regulator for a piezoelectric actuated smart structure using a high-precision laser interferometry measurement system to suppress the excitation of vibratory modes.

The analytical model of the smart structure is derived using the …

Inquiry Of Graphene Electronic Fabrication, John Rausch Greene

Master's Theses

Graphene electronics represent a developing field where many material properties and devices characteristics are still unknown. Researching several possible fabrication processes creates a fabrication process using resources found at Cal Poly a local industry sponsor. The project attempts to produce a graphene network in the shape of a fractal Sierpinski carpet. The fractal geometry proves that PDMS microfluidic channels produce the fine feature dimensions desired during graphene oxide deposit. Thermal reduction then reduces the graphene oxide into a purified state of graphene. Issues arise during thermal reduction because of excessive oxygen content in the furnace. The excess oxygen results in …

Investigation Of Degradation Effects Due To Gate Stress In Gan-On-Si High Electron Mobility Transistors Through Analysis Of Low Frequency Noise, Michael Curtis Meyer Masuda

Master's Theses

Gallium Nitride (GaN) high electron mobility transistors (HEMT) have superior performance characteristics compared to Silicon (Si) and Gallium Arsenide (GaAs) based transistors. GaN is a wide bandgap semiconductor which allows it to operate at higher breakdown voltages and power. Unlike traditional semiconductor devices, the GaN HEMT channel region is undoped and relies on the piezoelectric effect created at the GaN and Aluminum Gallium Nitride (AlGaN) heterojunction to create a conduction channel in the form of a quantum well known as the two dimensional electron gas (2DEG). Because the GaN HEMTs are undoped, these devices have higher electron mobility crucial for …

Lunalight - Bringing Light To The Expanding World, Gabriela M. Igel, Daniel J. Patrick, Kimberley M. Smith

Materials Engineering

The LunaLight, a solar rechargeable light and cell phone charger, addresses the lack of access to electricity faced by 1.4 billion of the world’s population (International Finance Corporation). The LunaTech team has developed a product that is bright, simple, compact, versatile and competitive with existing products. Through a partnership with the non-profit organization One Million Lights, LunaTech has improved a previous team’s design to address user feedback, concerns of durability, and manufacturability.

The LunaLight design includes a 5 component plastic housing held together by 4 screws, a surface mounted PCB, a lithium-ion (Li-Ion) battery, one high-brightness LED, a solar panel, …

Characterization And Modeling Of An O-Band 1310 Nm Sampled-Grating Distributed Bragg Reflector (Sg-Dbr) Laser For Optical Coherence Tomography (Oct) Applications, Desmond Charles Talkington

Master's Theses

In this project, the performance aspects of a new early generation 1310 nm Sampled-Grating Distributed Bragg Reflector (SG-DBR) semiconductor laser are investigated. SG-DBR lasers are ideal for Source Swept Optical Coherence Tomography (SS-OCT), a Fourier-Domain based approach for OCT, necessitating a tunable wavelength source. Three internal sections control the frequency output for tuning, along with two amplifiers for amplitude control. These O-band SG-DBR devices are now being produced in research quantities. SG-DBR lasers have been produced at 1550 and 1600 nm for some times. Fundamental questions regarding the performance of the 1310 nm devices must be quantified. Standard metrics including …

Dc, Rf, And Thermal Characterization Of High Electric Field Induced Degradation Mechanisms In Gan-On-Si High Electron Mobility Transistors, Matthew Anthony Bloom

Master's Theses

Gallium Nitride (GaN) high electron mobility transistors (HEMTs) are becoming increasingly popular in power amplifier systems as an alternative to bulkier vacuum tube technologies. GaN offers advantages over other III-V semiconductor heterostructures such as a large bandgap energy, a low dielectric constant, and a high critical breakdown field. The aforementioned qualities make GaN a prime candidate for high-power and radiation-hardened applications using a smaller form-factor. Several different types of semiconductor substrates have been considered for their thermal properties and cost-effectiveness, and Silicon (Si) has been of increasing interest due to a balance between both factors.

In this thesis, the DC, …

Fabrication And Characterization Of Torsional Micro-Hinge Structures, Mike Madrid Marrujo

Master's Theses

ABSTRACT

Fabrication and Characterization of Torsional Micro-Hinge Structures

Mike Marrujo

There are many electronic devices that operate on the micrometer-scale such as Digital Micro-Mirror Devices (DMD). Micro actuators are a common type of DMD that employ a diaphragm supported by torsional hinges, which deform during actuation and are critical for the devices to have high stability and reliability. The stress developed within the hinge during actuation controls how the actuator will respond to the actuating force. Electrostatically driven micro actuators observe to have a fully recoverable non-linear viscoelastic response. The device consists of a micro-hinge which is suspended by two …

Final Design Review: Design Of An Integrated Solar Cell Array To Power A Solar Ear Hearing Aid Battery Recharger, Christina (Chrissa) Blattner, Scott Carey, Jared Myren, Faye Siao

Materials Engineering

As the energy of fossil fuel supplies are fast depleting due to high consumptions of energy by human beings, the need for other sources of energy, such as solar energy, has become a viable option. By creating solar cell arrays the desired voltage can be generated. The overall goal of the Solar Ear project is to create an array of photovoltaic cells connected with aluminum tracings to recharge batteries that are specifically used for hearing aids. The goal embodies two main areas: the design of a processing method to connect the cells during a micro-fabrication process and the creation of …

Enhanced Light Extraction Efficiency From Gan Light Emitting Diodes Using Photonic Crystal Grating Structures, Simeon S. Trieu

Master's Theses

Gallium nitride (GaN) light emitting diodes (LED) embody a large field of research that aims to replace inefficient, conventional light sources with LEDs that have lower power, higher luminosity, and longer lifetime. This thesis presents an international collaboration effort between the State Key Laboratory for Mesoscopic Physics in Peking University (PKU) of Beijing, China and the Electrical Engineering Department of California Polytechnic State University, San Luis Obispo. Over the course of 2 years, Cal Poly’s side has simulated GaN LEDs within the pure blue wavelength spectrum (460nm), focusing specifically on the effects of reflection gratings, transmission gratings, top and bottom …

Optimization Of Gan Laser Diodes Using 1d And 2d Optical Simulations, Sean Richard Keali'i Jobe

Master's Theses

This paper studies the optical properties of a GaN Laser Diode (LD). Through simulation, the GaN LD is optimized for the best optical confinement factor. It is found that there are optimal thicknesses of each layer in the diode that yield the highest optical confinement factor. There is a strong relationship between the optical confinement factor and lasing threshold—a higher optical confinement factor results in a lower lasing threshold. Increasing optical confinement improves lasing efficiency. Blue LDs are important to the future of lighting sources as they represent the final color in the RGB spectrum that does not have a …