Electrical and Electronics Commons^™

Impacts Of Plug-In Electric Vehicle On Residential Electric Distribution System Using Stochastic And Sensitivity Approach, Henry Chigozie Ureh

Master's Theses

Plug-in Electric Vehicles (PEVs) are projected to become a viable means of transportation due to advances in technology and advocates for green and eco-friendly energy solutions. These vehicles are powered partially, or in some cases, solely by the energy stored in their battery packs. The large sizes of these battery packs require large amount of energy to charge, and as the demand for PEV increases, the increase in energy demand needed to recharge these PEV batteries could pose problems to the present electric distribution system. This study examines the potential impacts of PEV on a residential electric distribution system at …

Development And Prototyping Of A Ground Fault Circuit Interrupter For 3-Phase 480 Volt Systems, Matthew R. Norlander

Master's Theses

Ground Fault Circuit Interrupter (GFCI) technology was first introduced in the NEC in 1971, yet four decades later the technology has not been introduced to a great extent outside of the home environment. This thesis introduces the difficulties encountered in low-voltage three phase ground fault current detection, and adopts a previously patented tripping scheme to develop and prototype a digital relay for 3-phase 480 volt systems capable of the sensitivity and speed required for personnel safety. Results demonstrate the feasibility of the concept and suggest commercial development should be pursued. The prototype is capable of mA sensitivity and reliably detects …

Experimental And Numerical Investigations Of Tubular-Shaped Direct Methanol Fuel Cells (Dmfcs), Travis R. Ward

Master's Theses

This study focuses on both the numerical and experimental investigations of the novel, passively operated, tubular-shaped, Direct Methanol Fuel Cell (DMFC) as an alternative geometry to the traditional planar-shaped fuel cell. The benefit of the tubular geometry compared to the planar geometry is the higher instantaneous volumetric power density provided by the larger active area, which could be beneficial in applications that require a high instantaneous power while occupying a small volume. First, a two-dimensional, two-phase, non-isothermal model was developed to investigate the steady-state performance and design characteristics of a tubular-shaped, passive DMFC. It was found that a higher ambient …

Photovoltaic Emulator Adaptable To Irradiance, Temperature And Panel Specific I-V Curves, Joseph Gamos Durago

Master's Theses

This thesis analyzes the design and performance of a photovoltaic (PV) emulator. With increasing interest in renewable energies, large amounts of money and effort are being put into research and development for photovoltaic systems. The larger interest in PV systems has increased demand for appropriate equipment with which to test PV systems.

A photovoltaic emulator is a power supply with similar current and voltage characteristics as a PV panel. This work uses an existing power supply which is manipulated via Labview to emulate a photovoltaic panel. The emulator calculates a current-voltage (I-V) curve based on the user specified parameters of …

Bridgeless Active Power Factor Correction Using A Current Fed Push Pull Converter, Jeramie Seth Bianchi

Master's Theses

ABSTRACT

Bridgeless Active Power Factor Correction

Using a Current Fed Push Pull Converter

Jeramie Seth Bianchi

Switched Mode Power Supplies have become increasingly popular for efficient methods of delivering power to an assortment of electronic devices. This thesis proposes a method of using a current fed push pull converter to provide active power factor correction and rectification in a single stage. While most AC-DC converters utilize a bridge rectifier to convert AC-DC and then perform DC-DC conversion, the proposed circuit will utilize its output diodes to perform rectification, thus eliminating the need for a bridge rectifier. This circuit will also …

Development Of A Cubesat Instrument For Microgravity Particle Damper Performance Analysis, John Trevor Abel

Master's Theses

Spacecraft pointing accuracy and structural longevity requirements often necessitate auxiliary vibration dissipation mechanisms. However, temperature sensitivity and material degradation limit the effectiveness of traditional damping techniques in space. Robust particle damping technology offers a potential solution, driving the need for microgravity characterization. A 1U cubesat satellite presents a low cost, low risk platform for the acquisition of data needed for this evaluation, but severely restricts available mass, volume, power and bandwidth resources. This paper details the development of an instrument subject to these constraints that is capable of capturing high resolution frequency response measurements of highly nonlinear particle damper dynamics.

Off-Grid Public Lighting System – Design And Characterization Of An Led Luminaire, Quanghuy Le

Master's Theses

The technological advances made in the photovoltaic industry have led to a vast exploration of self-sustaining systems. As the consumer demand for electricity rises from increasing population and development of existing technologies, new practices in system designs are required to relieve the impact on the electrical grid.

This thesis delves into a developing concept of using photovoltaic modules for roadway lighting, with emphasis on establishing the fundamental design for a “spot-lighting” luminaire. By effectively extinguishing various sections of the luminaire in the absence of pedestrian trafficking, the proposed design and implementation will minimize the prolonged costs, as well as the …

Modeling And Analysis Of The Effects Of Pcb Parasitics On Integrated Dc-Dc Converters, Darwin Domingo Fernandez

Master's Theses

Load transients are prevalent in every electronic device including semiconductor memory, card readers, microprocessors, disc drives, piezoelectric devices, and digitally based systems. They are capable of producing voltage stress, introducing noise, and degrading device functionality. In order to avoid damage to the device, a feedback control loop is implemented with system compensation to regulate the output voltage deviations by the converter. Because designing compensation networks can be rather complicated, DC-DC converters with integrated feedback control topologies help minimize design time and complexity of converter compensation at the expense of design flexibility. This thesis widens the limitations of an integrated DC-DC …

A Frequency-Modulated Continuous Wave-Based Boundary Detection System For Determination Of Monitoring Region For An Indoor Ultra-Wideband Short Range Radar-Based Eldercare Monitoring System, Wilson Tang

Master's Theses

Falls are a cause of concern for the elderly since it can render a person immobile. A monitoring system can summon immediate aid by the automatic detection of fall events. The application of ultra-wideband (UWB) signals for a monitoring system was chosen due to its unique characteristics such as wide spectrum, immunity to interference, penetrability, and application for the detection of people. Part of this monitoring system is boundary detection with the purpose of isolating the location of fall events and to function as a mask to define an area of interest. A study of various localizing methods using measurements …

Energy Harvesting From Elliptical Machines Using Four-Switch Buck-Boost Topology, Alvin Jay Hilario

Master's Theses

This thesis presents the topic of using the Four-Switch Buck-Boost topology as a DC-DC converter for the Energy Harvesting from Elliptical Machines Project. The project works toward providing a modular synchronous power generation system. Due to the dynamic and sporadic output voltage and power characteristics of the Precor elliptical machine, the system requires a DC-DC converter as a voltage preregulator. The inherent wide input range, high efficiency, and low parts cost of this converter well suit the application. This paper further discusses other topologies and their shortcomings, as well as characterizes the Precor elliptical machine and Enphase Microinverter for interfacing. …

Design And Analysis Of A Wind Energy Harvesting Circuit Using Piezoelectric Polymers, Jameson J. Thornton

Master's Theses

This thesis investigates a relatively new method for harvesting wind energy by using flexible piezoelectric polymers with additional sails to increase their ability to harvest wind energy. This paper also introduces a new topology deemed the “stacked buck” that allows for multiple inputs to a system with a single output. Derivations and analysis detail the workings of the “stacked buck” with a laboratory test to show a working model. This paper also reports another experiment done in a wind tunnel to analyze the capability of the piezoelectric polymers as sources to the “stacked buck” topology with measurements of the power …

Universal Engineering Programmer – An In-House Development Tool For Developing And Testing Implantable Medical Devices In St. Jude Medical, Khoa Tat Do

Master's Theses

During development and testing of the functionality of the pacemaker and defibrillator device, engineers in the St. Jude Medical Cardiac Rhythm Management Division use an in-house development tool called Universal Engineering Programmer (UEP) to ensure the device functions as expected, before it can be used to test on an animal or a human during the implantation process. In addition, some applications of UEP are incorporated into the official releases of the device product. UEP has been developed and used by engineers across departments in the St. Jude Medical Cardiac Rhythm Management Division (CRMD). This thesis covers the flexible and reusable …