Electrical and Electronics Commons^™

Multiple Output Power Supply Using Toroidal Transformers For Medium Voltage Active Gate Drivers, Samhitha Venkata Machireddy

Graduate Theses and Dissertations

When operating in high power applications, power devices dissipate tens or hundreds of watts of power in the form of heat. The ability of the power devices to withstand power and dissipation of heat across the power devices becomes a prominent requirement in designing the power converter. This challenge demands a power converter design to be more effective and consistent which factors in size, cost, weight, power density and reliability. This study aims to propose a gate driver isolated power supply design that can be used in medium voltage applications (e.g., up to 10 kV) while respecting the principle of …

Power Line Coupling Power Supply Design, Janine Gian Christii C. Darato, Jeni K. Kawate, Nicholas A. Marta

Electrical Engineering

In this project, a power supply was designed for a startup company, Perch Sensing, to detect wildfires with the use of distributed sensors across power lines. The purpose of the power supply is to provide 15W of power to a microcontroller, which controls the sensor nodes. The power supply hangs from power lines and draws energy by inductively coupling to these lines. Our design starts with a current transformer that steps down the current from the power line, which is fed into a shunting mechanism as a safety precaution when the load is absent, then to the power supply itself. …

Assessment Of Cable Length Limit For Effective Protection By Z-Source Circuit Breakers In Dc Power Networks, Ruiyun Fu, Sagar Bhatta, Joseph M. Keller, Yucheng Zhang

Electrical & Computer Engineering Faculty Publications

This paper introduces groundbreaking research on how to assess the Cable Length Limit (CLL) to ensure effective protection by Z-source Circuit Breakers (ZCBs) in DC power networks. It has been revealed that the line parameters of power cables have a significant impact on the cutoff performance of ZCBs. The question of assessing the CLL has been raised as an unsolved problem. In this paper, a method of CLL assessment is proposed based on physical models and simulation tests. To verify the proposed method, two studies were performed to assess the Cable Length Limits depending on fault levels and power delivery …

Spread Spectrum Buck Converter, Summer Elise Rutherford, Kyle Brandon Halloran, Brian Taylor Arbiv

Electrical Engineering

Electromagnetic interference (EMI) is an issue prevalent to DC-DC converters. When a system doesn’t effectively filter out external noise or signals, these signals can cause disturbances to the system at large. The switching technology of DC-DC converters (PWM in particular), lends the system susceptible to EMI because there is a prevalent peaks at the switching frequency, meaning any external signals will not be effectively attenuated at this frequency. This can cause significant issues at the input bus of the DC-DC converters because this bus is likely the input of a multitude of devices; the EMI susceptibility caused by switching technology …

Dual High-Voltage Power Supply For Use On Board A Cubesat, Nicholas Weiser

Master's Theses

Since their conception in 1999, CubeSats have come and gone a long way. The first few that went into space were more of a “proof of concept,” and were more focused on sending simple data and photographs back to Earth. Since then, vast improvements have been made by over 40 universities and private firms, and now CubeSats are beginning to look towards interplanetary travel. These small satellites could provide a cost effective means of exploring the galaxy, using off the shelf components and piggy-backing on other launch vehicles with more expensive payloads. However, CubeSats are traditionally launched into Low Earth …

Power Supply Electrical Design, Robert Mayers, Matt Olson, Zach Bryant, Ali Haider, Stephen Holmes, Paul Johnson, Noah Root, Josh Berk, Jeremy Straub

Jeremy Straub

No abstract provided.

Pulse Density Modulated Soft Switching Cycloconverter, Jesse Timothy Adamson

Master's Theses

Single stage cycloconverters generally incorporate hard switching at turn on and soft switching at turn off. This hard switching at turn on combined with the slow switching speeds of thyristors (the switch of choice for standard cycloconverters) limits their use to lower frequency applications.

This thesis explores the analysis and design of a pulse density modulated (PDM), soft switching cycloconverter. Unlike standard cycloconverters, the controller in this converter does not adjust thyristor firing angles. It lets only complete half cycles of the input waveform through to the output. This allows and requires a much greater frequency step down from the …