Electrical and Electronics Commons^™

Tri-Level Hierarchical Coordinated Control Of A Largescale Electric Vehicle Charging In The Smart Grid, Tawfiq M. Aljohani

FIU Electronic Theses and Dissertations

Electric Vehicles (EVs) are considered one of humanity's greatest hopes to combat the climate change crises in light of their great potentials to reduce Greenhouse Gases (GHG) emissions from two main sources: the electric power industry and the fossil-based transportation sector. To help expedite the large-scale adoption of EVs on the roads, optimal solutions are needed to overcome the technical and operational barriers that face the electrical network. This is due to the introduction of significant load levels from EVs; a substantial number is expected during peak demand hours. This dissertation addresses the various interaction between different parts of the …

Enhanced Security Utilizing Side Channel Data Analysis, Michael Taylor

Computer Science and Engineering Theses and Dissertations

The physical state of a system is affected by the activities and processes in which it is tasked with carrying out. In the past there have been many instances where such physical changes have been exploited by bad actors in order to gain insight into the operational state and even the data being held on a system. This method of side channel exploitation is very often effective due to the relative difficulty of obfuscating activity on a physical level. However, in order to take advantage of side channel data streams one must have a detailed working knowledge of how a …

Modeling And Control Of A 7-Level Switched Capacitor Rectifier For Wireless Power Transfer Systems, Spencer Cochran

Doctoral Dissertations

Wireless power continues to increase in popularity for consumer device charging. Rectifier characteristics like efficiency, compactness, impedance tunability, and harmonic content make the multi-level switched capacitor rectifier (MSC) an exceptional candidate for modern WPT systems. The MSC shares the voltage conversion characteristics of a post-rectification buck-boost topology, reduces waveform distortion via its multi-level modulation scheme, demonstrates tank tunability via the phase control inherent to actively switched rectifiers, and accomplishes all this without a bulky filter inductor. In this work, the MSC WPT system operation is explained, and a loss model is constructed. A prototype system is used to validate the …

Ac/Dc Led Light Bulb Adaptor With Internal Rechargeable Batteries, Esteban A. Rubio, Matthew R. Delaby

Electrical Engineering

To make a sustainable product and provide a temporary source of lights on during emergencies, this project aims to create a small unit that can be attached to a light bulb of any variety and connect it to a socket. Within the device is a rechargeable battery that, when the device is not connected to an 120V AC, 240V AC, or 48V DC power source, will power the light for a short period of time. The battery can be charged during the standard operation of the device and can be powered by the US and EU standard outlet voltages as …

A Double-Sided Stack Low-Inductance Wire-Bondless Sic Power Module With A Ceramic Interposer, Si Huang

Graduate Theses and Dissertations

The objective of this dissertation research is to develop a novel three-dimensional (3-D) wire bondless power module package for silicon carbide (SiC) power devices to achieve a low parasitic inductance and an improved thermal performance. A half-bridge module consisting of 900-V SiC MOSFETs is realized to minimize stray parasitic inductance as well as to provide both vertical and horizontal cooling paths to maximize heat dissipation. The proposed 3-D power module package was designed, simulated, fabricated and tested. In this module, low temperature co-fired ceramic (LTCC) substrate with vias is utilized as an interposer of which both top and bottom sides …

Partial Discharge Testing And Detection Under Pwm Voltage, John Meadors

Masters Theses

Partial Discharge detection and measurement is an important part of electric insulation design. However, in PWM (pulse width modulation) voltage source converter environments, the noise resulting from switching voltage (rise and fall times of tens of nanoseconds) makes detection and extraction of partial discharge difficult. Unique methods of partial discharge detection are needed to address and decouple the noise from partial discharge measurements. PWM voltage can feature high switching speeds and high dv/dt during voltage switching. These PWM voltage behaviors are not found in traditional utility high voltage applications, and the effects that this type of voltage has on insulation …

Protection And Disturbance Mitigation Of Next Generation Shipboard Power Systems, Marounfa Djibo

Electrical & Computer Engineering Theses & Dissertations

Today, thanks to modern advances mainly in the power electronics field, megawatt-level electric drives and magnetic levitation are being integrated into the marine power grids. These technologies operate based on Direct Current (DC) power which require Alternating Current (AC) to DC conversion within the current grid. Medium-voltage Direct Current (MVDC) and Flywheel Energy Storage Systems (FESS) are the next state-of-the-art technologies that researchers are leaning on to produce, convert, store, and distribute power with improved power quality, reliability, and flexibility. On the other hand, with the extensive integration of high-frequency power electronic converters, system stability analysis and the true system …

Novel Zcs Pwm Methods For Industrial Applications, Ramtin Rasoulinezhad

Electronic Thesis and Dissertation Repository

Pulse width modulation (PWM) converters that consist of two or more interleaved boost/buck converter modules are used widely in industry. Soft-switching approaches for these converters can either be zero-voltage switching (ZVS) if implemented with MOSFETs or zero-current switching (ZCS) if implemented with IGBTs. The main idea of this thesis is to implement ZCS for IGBT turn-on and turn-off. Most converters use an auxiliary circuit that is activated whenever a main converter switch is about to be turned off, gradually diverting current away from the switch so that it can turn off with ZCS.

ZCS-PWM converters that use an auxiliary circuit …

The Effect Of A Ferrite-Core Relay Vs. An Air-Core Relay On The Output Power Characteristics Of A Three-Coil Wireless Power Transfer System, Jakob L. White

University Honors Theses

The purpose of this thesis is to determine the effect of using a ferrite-core relay on the output power characteristics of a three-coil, parallel-tuned, domino-resonator wireless power transfer (WPT) system in comparison to the effect of using an air-core relay in such a system. First, a general mathematical model is presented to describe both the ferrite-core-relay system and the air-core-relay system and to calculate their output power characteristics for seven different resistive loads at each of five different distance configurations between the coils. Next, experimental results are analyzed and compared to the mathematical results to confirm model accuracy. Finally, the …

Metodología De Comparación De Eficiencias En Sistemas Híbridos Off-Grid., Cristian Kevin Aguilar Lozano

Ingeniería Eléctrica

Debido al crecimiento de la generación de energía renovable se requiere estudios relacionados a su eficiencia ya que es uno de los tópicos en los que aún las fuentes convencionales son superiores. Los estudiantes de la universidad de La Salle están interesados en desarrollar proyectos de investigación que permitan generar conocimientos aplicativos por lo que se propone comparar las eficiencias de diferentes sistemas de gestión de energía basados en las topologías híbridas haciendo uso de convertidores DC/DC que permita una flexibilidad en la tensión de salida; Hasta el momento se han realizado estudios para obtener ecuaciones de la eficiencia de …

Design And Validation Of A High-Power, High Density All Silicon Carbide Three-Level Inverter, Zhongjing Wang

Graduate Theses and Dissertations

Transportation electrification is clearly the road toward the future. Compared to internal combustion engine, the electrified vehicle has less carbon-dioxide emission, less maintenance costs and less operation costs. It also offers higher efficiency and safety margin. More importantly, it relieves human’s dependence on conventional fossil energy. In the electrification progress, the revolution of electric traction drive systems is one of the most important milestone. The traction system should keep high efficiency to avoid performance reduction. Moreover, the motor drive should be designed within limited space without sacrificing output power rating. Based on the road map from US Drive Electrical and …

Buck Converter With Voltage Foldback Protection, Fabian Aaron Enriquez, Pedro Rincon Rosales

Electrical Engineering

In this work, we implemented the idea of current foldback protection onto a buck converter. Current foldback protection essentially helps reduce the power dissipation which may be caused by a short circuit or overload scenario. To achieve the goal of this project, we used a combination of comparators, operational amplifiers and MOSFETs to create a current foldback sub controller. This controller would then serve as a feedback device between the output of the converter and the main controller to detect if a fault condition has occurred. Following the design, we performed simulation of the current foldback controller using PSpice and …

Power Line Coupling Power Supply Design, Janine Gian Christii C. Darato, Jeni K. Kawate, Nicholas A. Marta

Electrical Engineering

In this project, a power supply was designed for a startup company, Perch Sensing, to detect wildfires with the use of distributed sensors across power lines. The purpose of the power supply is to provide 15W of power to a microcontroller, which controls the sensor nodes. The power supply hangs from power lines and draws energy by inductively coupling to these lines. Our design starts with a current transformer that steps down the current from the power line, which is fed into a shunting mechanism as a safety precaution when the load is absent, then to the power supply itself. …

Dc-Dc Buck Boost Converter Using The Lt8390 Controller And Gan High Electron Mobility Transistors, Juan Manuel Urbano Jr, Brian Thongchai Keokot

Electrical Engineering

California Polytechnic State University, San Luis Obispo’s ongoing Energy Harvesting from Exercise Machines (EHFEM) project creates a sustainable energy source by converting physical exercise from exercise machines into renewable electricity. Implementing energy harvesting technology into the Recreation Center’s exercise machines helps Cal Poly make progress on its goal of carbon neutrality by 2050 [1]. An improvement to the system with new technology increases Cal Poly Recreation Center’s ability to save money and improve sustainability.

The focus of this project improves the design of Nicholas Serres, who used the LT8390 controller in his buck boost DC-DC converter [2]. This project improves …

Wildfire Early Detection System (Weds), Mason Mciver, Vincent Liang, Jeanreno Racines

Electrical Engineering

With climate change causing an increase in temperature over the past several decades, wildfires have been burning hotter and moving quicker leaving a trail of destruction in their path. Detecting a wildfire early allows firefighters to respond efficiently and effectively to ensure containment. With the rise of advanced computer vision and algorithms, autonomous systems can be used to monitor and report any fire activity. Having multiple devices spread out across a large area will allow first responders to map out the fire location and track the fire. By utilizing smart technologies, property damage can be minimized and residents living in …

Miniaturized Ultraviolet Imager High Voltage Power Supply, Nicholas Palmer, Jason Thomas Heil

Electrical Engineering

Sending satellites into orbit becomes exponentially more expensive with weight and size, so designing high-voltage DC-DC converters that can achieve kilovolt level outputs in a small form factor is crucial to reducing costs. The Miniaturized Ultraviolet Imager (MUVI) aims to monitor Earth’s ionosphere and report weather patterns to climate scientists within a 2U cube satellite footprint. The imaging equipment consists of a microchannel plate and phosphor screen that require 2.5kV and 5.5kV respectively at microamp level currents. This report explains the implementation of a high voltage boost cascaded flyback converter to meet all of the MUVI satellite output voltage requirements. …

Power Management And Control To Balance Residential Microgrids With Individual Phase-Wise Generation And Storage, Syed Ahmed Raza Naqvi

Electronic Thesis and Dissertation Repository

The past decade has seen a significant rise in proliferation of roof-top photovoltaic (PV) systems with storage units at residential sites. This has affected the way power system engineers and researchers have previously studied distribution systems as passive networks. With the introduction of these local distributed energy resources, a distribution system has become part of an active network. This modernization of the power distribution network, brings along with itself a number of key issues that need to be pro-actively tackled by the local utilities.

In North America, with family-owned roof-top PV systems, storage devices and electric vehicles, the concept of …

Smart E-Bike Conversion Kit And Helmet, Megan West, Marena Trujillo, Hossein Asghari

Honors Thesis

With many state governments across the United States implementing shutdowns to prevent the spread of COVID-19, many bike retailers have seen dramatic increases in bike sales. Electric bicycles (e-bikes) have become increasingly popular as the public searches for alternatives to public transportation. Unfortunately, e-bike users assume some risk by riding bikes that are faster than conventional bicycles. While kits to convert conventional bicycles to e-bikes exist, no “smart” e-bike/helmet kit specifically designed to keep the user safe is currently available on the market. To mitigate risks, a smart e-bike conversion kit with multiple novel safety features, including auditory and visual …

Transimpedance Amplification Of Optocoupler Output For High Temperature Applications, Kara Maurer

Electrical Engineering Undergraduate Honors Theses

When looking to the future of electronics, one characteristic is becoming more lucrative: high temperature capabilities. With the goals of not only becoming more efficient electronically, spatially, and cost-wise, adapting electronics for a high temperature environment can potentially be a route to all three of these goals. Not only does it take away the need for a cooling method, but it can also increase the longevity of a product which can make it even more cost effective. In an effort to contribute to the push for high temperature electronics, the University of Arkansas is developing a high temperature power module …

Impact Of Wind Generation On Transmission Voltage Support During Weak Grid, Yugo Isogai

Electrical Engineering Undergraduate Honors Theses

Today, there are concerns about the effects of high wind penetration on electric power system operations. This is due to the more distributed nature of wind turbine generation and the corresponding multi-path power flows on the electric power transmission grid. In particular, the higher line impendences associated with inverter-based wind generation results in larger voltage fluctuation under varying load. This may results in conditions where even after a fault condition has been cleared, the transmission system voltages may not recover. Therefore, this paper concentrates on the impact of weak grid condition for voltage instability. To approach it, a 6-bus system …

Analog Spiking Neural Network Implementing Spike Timing-Dependent Plasticity On 65 Nm Cmos, Luke Vincent

Graduate Theses and Dissertations

Machine learning is a rapidly accelerating tool and technology used for countless applications in the modern world. There are many digital algorithms to deploy a machine learning program, but the most advanced and well-known algorithm is the artificial neural network (ANN). While ANNs demonstrate impressive reinforcement learning behaviors, they require large power consumption to operate. Therefore, an analog spiking neural network (SNN) implementing spike timing-dependent plasticity is proposed, developed, and tested to demonstrate equivalent learning abilities with fractional power consumption compared to its digital adversary.

Design And Assembly Of High-Temperature Signal Conditioning System On Ltcc With Silicon Carbide Cmos Circuits, Sajib Roy

Graduate Theses and Dissertations

The objective of the work described in this dissertation paper is to develop a prototype electronic module on a low-temperature co-fired ceramic (LTCC) material. The electronic module would perform signal conditioning of sensor signals (thermocouples) operating under extreme conditions for applications like gas turbines to collect data on the health of the turbine blades during operation so that the turbines do not require shutdown for inspection to determine if maintenance is required. The collected data can indicate when such shutdowns, which cost $1M per day, should be scheduled and maintenance actually performed. The circuits for the signal conditioning system within …

Ironless, Axial Flux, Electric Bldc Motor For Aircraft Electric Propulsion, Kevin W. Hobbs

Electrical Engineering Undergraduate Honors Theses

3D printing has shown much promise as a method of rapidly manufacturing lightweight ironless motors to meet the growing demand that airlines have for more cost-effective products that reduce emissions and flight prices. 3D-printed ironless, axial flux, electric BLDC motors would meet these needs with both their high efficiency and power density.

A Halbach array motor was designed and 3D-printed for the analysis of its magnetic properties to gain more insight about it performance. Fusion 360 was used to design the 3D drawings of the motor parts. The rotor, stator, and stator mount were designed to accommodate the sizes of …

Design And Fabrication Of A Microstrip Bandpass Filter In Ltcc, Allison Rucker

Electrical Engineering Undergraduate Honors Theses

The goal of the project was to design and fabricate a bandpass filter with a center frequency of 25GHz with a 2GHz bandwidth. The first step was to do the calculation to design a bandpass filter to meet these specifications along with the properties of the Dupont^TM GreenTape^TM 9K7. HFSS was then used to verify the results from the initial calculations. There was a significant error between the two results, so more tweaking was done to the calculations to get a better center frequency. After a final design was decided, the fabrication process started. Low-Temperature Co-Fired Ceramics (LLTC) …

Performance And Economics Of Solar Inverters And Module Level Power Electronics In A 1 Mw Photovoltaic System, Maxwell Criswell

Biological and Agricultural Engineering Undergraduate Honors Theses

Photovoltaic solar panels convert sunlight to electricity in the form of direct current; therefore, a necessary component of every photovoltaic system is an inverter to convert the electricity to usable alternating current. There are various commercially available inverter technologies manufactured today such as microinverters, string inverters, and central inverters, as well as module level power electronic devices such as DC optimizers that are capable of improving system performance in string and central inverter systems. This thesis compares the performance and economics of five different inverter and module level power electronic systems through model simulation using Helioscope software. The five alternatives …

An 8-Bit Analog-To-Digital Converter For Battery Operated Wireless Sensor Nodes, Marvin Wayne Suggs Jr.

Graduate Theses and Dissertations

Wireless sensing networks (WSNs) collect analog information transduced into the form of a voltage or current. This data is typically converted into a digital representation of the value and transmitted wirelessly using various modulation techniques. As the available power and size is limited for wireless sensor nodes in many applications, a medium resolution Analog-to-Digital Converter (ADC) is proposed to convert a sensed voltage with moderate speeds to lower power consumption. Specifications also include a rail-to-rail input range and minimized errors associated with offset, gain, differential nonlinearity, and integral nonlinearity. To achieve these specifications, an 8-bit successive approximation register ADC is …

Memory Module Design For High-Temperature Applications In Sic Cmos Technology, Affan Abbasi

Graduate Theses and Dissertations

The wide bandgap (WBG) characteristics of SiC play a significant and disruptive role in the power electronics industry. The same characteristics make this material a viable choice for high-temperature electronics systems. Leveraging the high-temperature capability of SiC is crucial to automotive, space exploration, aerospace, deep well drilling, and gas turbines. A significant issue with the high-temperature operation is the exponential increase in leakage current. The lower intrinsic carrier concentration of SiC (10-9 cm-3) compared to Si (1010 cm-3) leads to lower leakage over temperature. Several researchers have demonstrated analog and digital circuits designed in SiC. However, a memory module is …

Development Of A Converter-Based Testing Platform And Battery Energy Storage System (Bess) Emulator For Microgrid Controller Function Evaluation, Dingrui Li

Masters Theses

The microgrid has attracted increasing research attention in the last two decades. Due to the development of renewable energy resources and power electronics technologies, the future microgrid will trend to be smarter and more complicated. The microgrid controller performs a critical role in the microgrid operation, which will also become more and more sophisticated to support the future microgrid. Before final field deployment and test, the evaluation and testing of the controller is an indispensable step in the controller development, which requires a proper testing platform.

However, existing simulation-based platforms have issues with potential numerical oscillation and may require huge …

Enercon Station Vacuum Pump Replacement, Clint Hembree, Jared D'Amico, Connor Moore, Paul Jeffrey Fontenot, Sydnee Castello, J.J. Clements

Senior Design Project For Engineers

This details the progress of the ENERCON pump replacement project as completed by the Kennesaw State University interdisciplinary senior design group. This project is a two-semester capstone effort for the engineering program at Southern Polytechnic School of Engineering, overseen by Dr. McFall during Fall 2020 and Dr. Khalid during Spring 2021 semesters. The 2020-2021 KSU Interdisciplinary Senior Design team was tasked with completing an Engineering Change Package (ECP) for existing vacuum pumps at ENERCON Station. The mechanical, electrical, and civil students worked together, performing evaluations on existing plant systems to ensure the plant could support the new vacuum pumps. By …

A Magneto-Mechanical Piezoelectric Energy Harvester Designed To Scavenge Ac Magnetic Field From Thermal Power Plant With Power-Line Cables, Quan Wang, Kyung-Bum Kim, Sang-Bum Woo, Yooseob Song, Tae-Hyun Sang

Civil Engineering Faculty Publications and Presentations

Piezoelectric energy harvesters have attracted much attention because they are crucial in portable industrial applications. Here, we report on a high-power device based on a magneto-mechanical piezoelectric energy harvester to scavenge the AC magnetic field from a power-line cable for industrial applications. The electrical output performance of the harvester (×4 layers) reached an output voltage of 60.8 V_max, an output power of 215 mW_max (98 mW_rms), and a power density of 94.5 mW_max/cm³ (43.5 mW_rms/cm³) at an impedance matching of 5 kΩ under a magnetic field of 80 …