Electrical and Electronics Commons^™

Design And Assembly Of High-Temperature Signal Conditioning System On Ltcc With Silicon Carbide Cmos Circuits, Sajib Roy

Graduate Theses and Dissertations

The objective of the work described in this dissertation paper is to develop a prototype electronic module on a low-temperature co-fired ceramic (LTCC) material. The electronic module would perform signal conditioning of sensor signals (thermocouples) operating under extreme conditions for applications like gas turbines to collect data on the health of the turbine blades during operation so that the turbines do not require shutdown for inspection to determine if maintenance is required. The collected data can indicate when such shutdowns, which cost $1M per day, should be scheduled and maintenance actually performed. The circuits for the signal conditioning system within …

Dc-Dc 4-Switch Buck-Boost Converter For Energy Harvesting From Elliptical Machines, Alexander C. Samietz, Gustavo Guzman

Electrical Engineering

The senior project report documents the process of replacing the network of resistors inside an elliptical machine with a DC-DC buck-boost converter. The buck-boost DC-DC converter accepts a wide input range of 5-60 Volts, with an output of 36 Volts for the most efficient use of the already available microinverter. The microinverter reclaims the lost energy and safely distributes it back to the electrical grid. The addition of this project reduces heat emissions from wasted energy and shrinks the carbon footprint of its users.

Dc-Dc Converter Control System For The Energy Harvesting From Exercise Machines System, Alexander Sireci

Master's Theses

Current exercise machines create resistance to motion and dissipate energy as heat. Some companies create ways to harness this energy, but not cost-effectively. The Energy Harvesting from Exercise Machines (EHFEM) project reduces the cost of harnessing the renewable energy. The system architecture includes the elliptical exercise machines outputting power to DC-DC converters, which then connects to the microinverters. All microinverter outputs tie together and then connect to the grid. The control system, placed around the DC-DC converters, quickly detects changes in current, and limits the current to prevent the DC-DC converters and microinverters from entering failure states.

An artificial neural …

Current Protection For The Energy Harvesting From Exercise Machines (Ehfem) Project, Colton Crivelli

Electrical Engineering

The Energy Harvesting from Exercise Machines (EHFEM) project intends to create an exercise machine that recycles the energy expended by an athlete operating the machine by sending it to the electric grid. The work done by the user goes through a DC-DC converter and an inverter in order to prepare it for delivery to the grid. A protection circuit ensures that the inverter does not try to pull too much current from the DC-DC converter. The project implements a current protection system that ensures the system doesn’t experience an overcurrent condition.

Análisis De Impacto Expost De La Implementación De Medidores Prepago Para La Empresa De Energía De Boyacá Ebsa S.A E.S.P, Zaret Natalia Mayorga Roncancio, Andrea Yesenia Molano Gómez

Ingeniería Eléctrica

Este trabajo presenta el análisis de impacto de la implementación de medidores prepago de servicio eléctrico en zonas rurales, a partir de los antecedentes técnicos y regulatorios en el país, se determinaron los tipos de medidores empleados en la actualidad en las zonas rurales colombianas, identificando características operacionales de este sistema, políticas regulatorias que se necesitaron para implementar este sistema, condiciones socioculturales, ambientales y económicas, para así identificar y analizar los impactos en los distintos aspectos sostenibles asociados con estas experiencias. Por último, este estudio identifica las ventajas y desventajas reales de la aplicación de estos sistemas para las empresas …

Energy Harvesting From Elliptical Machines: Dc-Dc Converter Design Using Sepic Topology, Martin Kou

Master's Theses

Cal Poly’s ongoing Energy Harvesting from Exercise Machines (EHFEM) project is a very convenient and cost-effective way for generating DC power from physical exercise and sending it back to the electrical grid as AC power, providing a renewable energy source for the future. The EHFEM project consists of numerous subprojects involving converting different types of exercise machines for power generation. This project is a continuation of one of the previous subprojects, specifically involving an elliptical machine, and focuses on improving system functionality at different machine settings without altering the elliptical user’s experience by selecting a new DC-DC converter design, while …