Electrical and Electronics Commons^™

Thermal And Electrical Parasitic Modeling For Multi-Chip Power Module Layout Synthesis, Zihao Gong

Graduate Theses and Dissertations

This thesis presents thermal and electrical parasitic modeling approaches for layout synthesis of Multi-Chip Power Modules (MCPMs). MCPMs integrate power semiconductor devices and drive electronics into a single package. As the switching frequency of power devices increases, the size of the passive components are greatly reduced leading to gains in efficiency and cost reduction. In order to increase switching frequency, electrical parasitics in MCPMs need to be reduced through tighter electronic integrations and smaller packages. As package size is decreased, temperature increases due to less heat dissipation capability. Thus, it is crucial to consider both thermal and electrical parasitics in …

Energy Harvesting Of Human Kinetic Movement, David Marusiak, Julia Carrillo

Electrical Engineering

Development of kinetic energy scavenging applications from the human body necessitates additional research to assist in designating a mounting position for a potential device. A data acquisition system adequately provides a parametric average power comparison among four locations on the body (waist, upper arm, hand, and calf) for both a male and female subject. Experimentally, the hand-held device provided the highest average power. Thus, subsequent investigation at set speeds provides further analysis of the output’s characteristically linear behavior. The physical energy-harvesting device features a plastic tube casing wrapped with the stationary coiled wire through which a neodymium magnet oscillates. While …

Smart Wall Plug Design For The Dc House Project, Edward Constant Sibal

Master's Theses

The DC House project at Cal Poly State University faces a challenge of supplying DC voltage to household appliances. Each appliance in the DC House constitutes a DC load that has a unique voltage and power rating, hence the need to develop a smart DC wall plug that will automatically adjust to the operating voltage required by any DC load. This thesis entails a proof of concept design of the smart DC wall plug which can automatically detect an appliance’s voltage rating. The design employs a dc-dc converter in conjunction with a microcontroller to sense load current to properly adjust …

Design And Simulation Of Interconnected H-Bridge Inverter, Samuel Muehleck

Computer Engineering

In this project, the research, design and simulation of an interconnected H-bridge single-phase inverter was explored. The inverter design was divided into three separate sections. First, a VHDL programmed CPLD was used to generate control signals for the transistors of the inverter circuit. Second, power electronics was used to create an inverter circuit to change a DC input to a 60 Hz AC output. Lastly, additional circuits were used to link the generated control signals to the MOSFET transistors of the inverter circuit. The operation of the three components was then validated with computer simulations. Results of computer simulation demonstrate …

Cell Phone Charger For The Dc House Project, Andrew Hefner, Antonio Magdaleno

Electrical Engineering

The goal of this project is to create a multiple output cell phone charger for the DC House project. The cell phone charger is essentially a DC-DC converter. The converter takes an input of 48 volts from the outlet in the DC House and decreases the voltage level to 5 volts; the input voltage level of all cellular devices. By designing an isolated flyback converter with initial specification in LTSpice simulation software, a converter was created. By monitoring the input and output voltage and current using the multi-meters and electronic load, we determined the charger to be 71% efficient when …

12 Volt Wall Outlet For The Dc House Project, Dylan Van Lant, Chenxi Zhang

Electrical Engineering

The purpose of this project is to build a DC-DC converter for the wall outlet of the DC House. This report focuses on the development of the DC -DC converter, and explains the design process as well as summarize the final results. The proposed system using the Buck or Step Down topology takes input voltage of 48V and output 12V at 100W. Results show the ability of the converter to fulfill such tasks while maintaining efficiency about 90% at all load.

Energy Harvesting From Elliptical Machines: Dc-Dc Converter Design Using Sepic Topology, Martin Kou

Master's Theses

Cal Poly’s ongoing Energy Harvesting from Exercise Machines (EHFEM) project is a very convenient and cost-effective way for generating DC power from physical exercise and sending it back to the electrical grid as AC power, providing a renewable energy source for the future. The EHFEM project consists of numerous subprojects involving converting different types of exercise machines for power generation. This project is a continuation of one of the previous subprojects, specifically involving an elliptical machine, and focuses on improving system functionality at different machine settings without altering the elliptical user’s experience by selecting a new DC-DC converter design, while …

Real-Time Selective Harmonic Minimization For Multilevel Inverters Using Genetic Algorithm And Artificial Neural Network Angle Generation, Faete Jacques Teixeira Filho

Doctoral Dissertations

This work approximates the selective harmonic elimination problem using Artificial Neural Networks (ANN) to generate the switching angles in an 11-level full bridge cascade inverter powered by five varying DC input sources. Each of the five full bridges of the cascade inverter was connected to a separate 195W solar panel. The angles were chosen such that the fundamental was kept constant and the low order harmonics were minimized or eliminated. A non-deterministic method is used to solve the system for the angles and to obtain the data set for the ANN training. The method also provides a set of acceptable …

Efficiency Performance Improvement Using Parallel Dc-Dc Converters With A Digital Controller, Daniel Forbes

Master's Theses

A system to improve efficiency performance of a DC-DC converter is simulated and built. The proposed system combines multiple DC-DC converters in parallel and implements a digital control scheme and load-share controller. A model of the system is developed in MATLAB Simulink and the model demonstrates the improved converter’s efficiency particularly at low load conditions. This simulation is then designed into a hardware system running three DC-DC converters in parallel, controlled by a microcontroller and a load-share controller. The hardware also confirms the simulation results, although some hardware refinements are evident as simulation results are superior. The system is designed …

Investigation On The Benefits Of Safety Margin Improvement In Candu Nuclear Power Plant Using An Fpga-Based Shutdown System, Jingke She

Electronic Thesis and Dissertation Repository

The relationship between response time and safety margin of CANadian Deuterium Uranium (CANDU) nuclear power plant (NPP) is investigated in this thesis. Implementation of safety shutdown system using Field Programmable Gate Array (FPGA) is explored. The fast data processing capability of FPGAs shortens the response time of CANDU shutdown systems (SDS) such that the impact of accident transient can be reduced. The safety margin, which is closely related to the reactor behavior in the event of an accident, is improved as a result of such a faster shutdown process.

Theoretical analysis based on neutron dynamic theory is carried out to …

Rapid Battery Interchange System, Mason Borda

Electrical Engineering

As our nation strives towards a departure from widespread use of fossil fuels, we must focus on a plan for what is to be the substitute for Internal Combustion Engine vehicles as well as the infrastructure to support this. The most popular alternative to the internal combustion engine is the electrically propelled vehicle, one that can provide us with many benefits including simplified construction, lower operational costs, and for the driving enthusiasts more torque. The prevailing issue in the widespread acceptance and use of the electric vehicle thus far is “range anxiety”. Range anxiety is defined as “The fear of …

Polar Field Oriented Control With 3rd Harmonic Injection, Martin Todd Hess

Master's Theses

Abstract

POLAR FIELD-ORIENTED CONTROL

with

3^RD HARMONIC INJECTION

Martin Todd Hess

Field Oriented Control (FOC), also known as vector control, is a widely used and well documented method for controlling Permanent-Magnet Synchronous Motors (PMSM) and induction motors. Almost invariably the orientation of the stator and rotor (field) fluxes are described in rectangular coordinates. In this thesis we explore the practicality of using polar coordinates.

Third harmonic injection is also a well-known technique that allows full utilization of the bus (DC-link), thus allowing the motor to run to full base speed without the use of field weakening. This technique potentially …