Electrical and Electronics Commons^™

Load Flow Analysis Of 138/69kv Substation Using Electrical Transient & Analysis Program (Etap), Vanessa Abadia Gomez

Electrical Engineering Undergraduate Honors Theses

This paper examines the load flow analysis of a high-voltage substation using ETAP, and explores options for improving the voltage profile of the system. This study yields critical information about the system, such as the voltage drop at each feeder, the voltage at each bus, as well as real and reactive power losses at the different branches and feeders. In this power flow examination, the system’s performance is evaluated for different operating conditions, so that control measurements can be applied if necessary. The experimental results are used for proposing a plan of using fixed and switched shunt capacitor banks to …

High Frequency Ltcc Based Planar Transformer, Adithya Venkatanarayanan

Graduate Theses and Dissertations

As we move towards high power and higher frequency related technology, conventional wire-wound magnetics have their own limitations which has led path to the development of planar based magnetic materials. Nowadays more planar magnetic technology has been employed because it is easier to fabricate them. The planar magnetic is a transformer or an inductor that replaces the wire-wound transformer or inductors which generally uses copper wires. One of the main reasons why we move to planar magnetic technology is its operation at higher frequency which provides higher power density. This study explains in detail about the design and fabrication of …

Design And Optimization Of A High Power Density Silicon Carbide Traction Inverter, Tyler Adamson

Graduate Theses and Dissertations

This project was initiated with the goal of demonstrating a 3-phase silicon carbide based 150-kW 25 kW/L DC-AC power conversion unit capable of operation with coolant temperatures up to 90°C. The project goals were met and exceeded by first analyzing the established inverter topologies to find which one would yield the highest power density while still meeting electrical performance needs in the 150-kW range. Following topology selection, the smallest silicon carbide power module that met the electrical requirements of the system was found through experimental testing and simulation. After a power module selection was finalized, a DC link capacitor bank …

Demand-Side Load Management Using Single-Phase Residential Static Var Compensators, Muhammad Kamran Latif

Boise State University Theses and Dissertations

Distribution systems are going through a structural transformation from being radially-operated simple systems to becoming more complex networks to operate in the presence of the distributed energy resources (DERs) with significant levels of penetration. It is predicted that the share of electricity generation from DERs will keep increasing as the world is moving away from the power generation involving carbon-emission and towards cleaner energy sources such as solar, wind, and biofuels. However, the unstable behavior of the renewables resources presents challenges to the already existing distribution systems. One such problem is when the distribution feeder experience variable power supply due …

Critical Radius Of Insulation, Maria N. Ambrose, Samuel J. Sayre, Travis W. Martin, Matt T. Sterling

Mechanical Engineering

The critical radius of insulation is a counterintuitive concept within the study of heat transfer. The theory states that adding insulation to a cylindrical or spherical object will increase the rate of heat loss rather than decrease it, if the radius (thickness) of the insulation is at its “critical” value. The Critical Radius of Insulation Senior Project is designed to demonstrate this phenomenon to Heat Transfer students via a portable apparatus. The concept will be demonstrated with a cylindrical object which is heated by way of a separate voltage source. Thermocouples will display the temperature of the cylinder while insulation …

Performance Enhancement And Characterization Of An Electromagnetic Railgun, Paul M. Gilles

Master's Theses

Collision with orbital debris poses a serious threat to spacecraft and astronauts. Hypervelocity impacts resulting from collisions mean that objects with a mass less than 1g can cause mission-ending damage to spacecraft. A means of shielding spacecraft against collisions is necessary. A means of testing candidate shielding methods for their efficacy in mitigating hypervelocity impacts is therefore also necessary. Cal Poly’s Electromagnetic Railgun was designed with the goal of creating a laboratory system capable of simulating hypervelocity (≥ 3 km/s) impacts. Due to several factors, the system was not previously capable of high-velocity (≥ 1 km/s) tests. A deficient projectile …

Novel Control Of Pv Solar Farms As Statcom (Pv-Statcom) For Frequency Control And Power Oscillation Damping, Mohammad Akbari Kelishadi

Electronic Thesis and Dissertation Repository

Frequency stability and low-frequency power oscillations are two major concerns in modern power systems. PV-STATCOM is a patented concept which enables PV inverters to provide STATCOM functions, during day and night, as well as real power modulation during daytime. This thesis aims to utilize PV-STATCOM capability effectively for enhancing frequency stability and power oscillations damping.

A novel, simultaneous real power-based Fast Frequency Response (FFR) and reactive power-based Power Oscillation Damping (POD) control is proposed for PV-STATCOMs. This control not only significantly reduces system under- and over-frequency deviations, but also uses the unutilized capacity of PV inverters to enhance damping of …

Edge Iot Driven Framework For Experimental Investigation And Computational Modeling Of Integrated Food, Energy, And Water System, Yemeserach Taye Mekonnen

FIU Electronic Theses and Dissertations

As the global population soars from today’s 7.3 billion to an estimated 10 billion by 2050, the demand for Food, Energy, and Water (FEW) resources is expected to more than double. Such a sharp increase in demand for FEW resources will undoubtedly be one of the biggest global challenges. The management of food, energy, water for smart, sustainable cities involves a multi-scale problem. The interactions of these three dynamic infrastructures require a robust mathematical framework for analysis. Two critical solutions for this challenge are focused on technology innovation on systems that integrate food-energy-water and computational models that can quantify the …

Design And Analysis Of Modular Axial Flux Switched Reluctance Motor, Rochak Shiwakoti

University of New Orleans Theses and Dissertations

This thesis presents a new modular structure of the axial flux Switched Reluctance Motor (SRM). The design consists of four stator disks with each adjacent disk rotated 30 degrees apart and four rotor disks connected to a common shaft. The proposed design aims to reduce the unwanted radial force, mitigate the torque ripple, and improve the efficiency. The modular structure distributes the radial force and torque strokes along the axial length of the motor, potentially damping the torque pulsation. In addition, the modular structure would deliver the rating power at a lower current level, reducing the overall ohmic loss. Moreover, …

Smart Charging Of Future Electric Vehicles Using Roadway Infrastructure, Sara Ahmed, Ethan Ahn, Mahmoud Reda Taha, Samer Dessouky, Moneeb Genedy, Daniel Fernandez, Ann Sebestian, Patience Raby

Publications

Inspired by the fact that there is an immense amount of renewable energy sources available on the roadways such as mechanical pressure and frictional heat, this study presented the development and implementation of an innovative charging technique for future electric vehicles (EVs) by fully utilizing the existing roadways and the state-of-the-art nanotechnology and power electronics. The project introduced a novel wireless charging system, SIC (Smart Illuminative Charging), that uses LEDs powered by piezoelectric nanomaterials as the energy transmitter source and thin film solar panels placed at the bottom of the EVs as the receiver, which is then poised to deliver …

Residential Electricity Management And Protection System, Ejimonu Kosisochukwu Gabriel

Journal of International Technology and Information Management

The Residential Electricity Monitoring System is an electricity meter connected to the Internet to provide real time data on the power system in your home. The REMS is designed to replace the distribution board allowing it to conduct a series of tests on the quality of the electricity supply to your home/facility and, within your home detect basic wiring faults and allow owners and service providers to identify potential problems with the electrical systems.

The electrical monitoring system finally puts proper electrical control into the hands of the home owner by providing him with the ability to control power distribution …

Energy Transformation And Conservation Investigation, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use a thermoelectric generator module to analyze the relationship between thermal and electrical energies. Using data collection sensors and analysis software, students will investigate the relationship between the temperature gradient across a thermoelectric generator module and the resulting electrical potential. Students will then use their data and analysis to solve problems relating to waste thermal energy in electrical systems and communicate their work to their peers and teacher.

Protection Of Active Distribution Networks And Their Cyber Physical Infrastructure, Hany Fawzy Kamel Habib

FIU Electronic Theses and Dissertations

Today’s Smart Grid constitutes several smaller interconnected microgrids. However, the integration of converter-interfaced distributed generation (DG) in microgrids has raised several issues such as the fact that fault currents in these systems in islanded mode are way less than those in grid connected microgrids. Therefore, microgrid protection schemes require a fast, reliable and robust communication system, with backup, to automatically adjust relay settings for the appropriate current levels according to the microgrid’s operation mode. However, risks of communication link failures, cyber security threats and the high cost involved to avoid them are major challenges for the implementation of an economic …

Weight Controlled Electric Skateboard, Zachary Barram, Carson Bertozzi, Vishnu Dodballapur

Computer Engineering

Technology and the way that humans interact is becoming more vital and omnipresent with every passing day. However, human interface device designers suffer from the increasingly popular “designed for me or people like me” syndrome. This design philosophy inherently limits accessibility and usability of technology to those like the designer. This places severe limits of usability to those who are not fully able as well as leaves non-traditional human interface devices unexplored. This project set out to explore a previously uncharted human interface device, on an electric skateboard, and compare it send user experience with industry leading human interface devices.

Multiple Input, Single Output Dc-Dc Conversion Stage For Dc House, Jason Baltierrez

Master's Theses

n this thesis project, a proposed architecture for the multiple input, single output conversion stage for the DC House was designed, simulated, and tested. This architecture allows for multiple different input sources to be used to create a single higher power output source. The design uses a DC-DC boost converter with a parallelable output which has been demonstrated to allow increased total output power as a function of the number of input sources available. The parallelable output has been shown to distribute load amongst the input sources relatively closely to optimize the system. This approach is also desirable since it …

Spread Spectrum Buck Converter, Summer Elise Rutherford, Kyle Brandon Halloran, Brian Taylor Arbiv

Electrical Engineering

Electromagnetic interference (EMI) is an issue prevalent to DC-DC converters. When a system doesn’t effectively filter out external noise or signals, these signals can cause disturbances to the system at large. The switching technology of DC-DC converters (PWM in particular), lends the system susceptible to EMI because there is a prevalent peaks at the switching frequency, meaning any external signals will not be effectively attenuated at this frequency. This can cause significant issues at the input bus of the DC-DC converters because this bus is likely the input of a multitude of devices; the EMI susceptibility caused by switching technology …

Dc-Dc Buck-Boost Converter For Energy Harvesting From Exercise Equipment, David T. Bolla

Electrical Engineering

This senior project helps harvest the excess energy that exercise equipment generates. Sustainable energy acts as the main target for this project, and it attempts this through reusing the energy created when exercising on elliptical machines. An elliptical machine outputs voltages between approximately 5V and 60V, and a micro-inverter requires an input voltage of about 36V. This DC-DC converter takes the variable output voltage of an elliptical machine and brings it to approximately 36V. Re-purposing the excess energy an elliptical user creates for the grid provides a sustainable alternative to dissipating the energy as heat. This project, along with other …

Dc To Dc Usb-C Charger, Nikki Gmerek, Kenneth Nguyen, Uriel Serna

Electrical Engineering

The DC House USB-C Charger will convert the 48V input from the DC house, found on the Cal Poly campus, to 3 USB-C outputs: 5V, 12V, and 24 volts. The converter will deliver a total of 185 Watts out across all 3 outputs, with an efficiency greater than 82% at full load. The USB-C ports will be used to connect to compatible phones, laptops or any other device for charging/powering purposes. The goal of this project is to develop the most efficient and safe converter to deliver power to multiple outputs using USB-C, for items as small as a cell …

Dc-Dc Converter For Electric Vehicle, Jason Y. Zhou, Nicholas James Mah

Electrical Engineering

In this work, a DC-DC converter is designed for an electric vehicle. The DC-DC converter is designed to provide 500W with a 200-400V input and a 12-15V adjustable output. Electric vehicle sales are beginning to increase in popularity and the need for DC-DC converters to siphon power from the tractive system is not yet fully satisfied, especially for single-seater class vehicles. Additionally, improving performance in efficiency without sacrificing wide input voltage range can benefit future DC-DC converter designs. In the end, a forward active clamp DC-DC converter is designed and tested. Additionally, spreadsheet calculators, LTSpice simulations, and Matlab scripts were …

Smart Dc Wall Outlet Design With Improved Load Voltage Detection, Patrick Donovon Granieri

Master's Theses

A standard home in the United States has access to the 120V AC power grid for use with home appliances. Many electronics used at home are powered by a DC power supply, which loses energy in the conversion from AC power. The DC House project avoids any conversion between AC and DC by storing energy in batteries as DC power and supplying it directly to DC appliances. While AC systems feature a standardized output voltage, no such standard exists for DC systems. The Smart DC Wall Outlet solves this by automatically adjusting its output voltage to meet any required DC …

Optimal And Efficient Decision-Making For Power System Expansion Planning, Mahdi Mehrtash

LSU Doctoral Dissertations

A typical power system consists of three major sectors: generation, transmission, and distribution. Due to ever increasing electricity consumption and aging of the existing components, generation, transmission, and distribution systems and equipment must be analyzed frequently and if needed be replaced and/or expanded timely. By definition, the process of power system expansion planning aims to decide on new as well as upgrading existing system components in order to adequately satisfy the load for a foreseen future.

In this dissertation, multiple economically optimal and computationally efficient methods are proposed for expanding power generation, transmission, and distribution systems. First, a computationally efficient …

Modeling Solder Ball Array Interconnects For Power Module Optimization, Paul Swearingen

Electrical Engineering Undergraduate Honors Theses

PowerSynth is a software platform that can co-optimize power modules utilizing a 2D topology and wire bond interconnects. The novel 3D architectures being proposed at the University of Arkansas utilize solder ball interconnects instead of wire bonds. Therefore, they currently cannot be optimized using PowerSynth. This paper examines methods to accurately model the parasitic inductance of solder balls and ball grid arrays so they may be implemented into software for optimization. Proposed mathematical models are validated against ANSYS Electromagnetics Suite simulations. A comparison of the simulated data shows that mathematical models are well suited for implementation into optimization software platforms. …

Very Low Power Cockcroft-Walton Voltage Multiplier For Rf Energy Harvesting Applications, Trace Langdon

Electrical Engineering Undergraduate Honors Theses

A device was required that could harvest the electromagnetic energy present in ambient radio frequency (RF) signals. A part of this device must convert the AC RF signal received by the antenna into a DC signal that can be used in an embedded application. Since the RF signal amplitude is small, it must first be amplified and rectified to become a usable signal. The Cockcroft-Walton voltage multiplier is a subsystem of the design which ideally converts a 100 mV AC signal coming from the antenna to a 350 mV DC signal. The output of the voltage multiplier is used to …

Synchrophasor-Based Fault Location Detection And Classification, In Power Systems, Using Artificial Intelligence, Hemal Falak

Graduate Theses and Dissertations

With the introduction of sophisticated electronic gadgets which cannot sustain interruption in the provision of electricity, the need to supply uninterrupted and reliable power supply, to the consumers, has become a crucial factor in the present-day world. Therefore, it is customary to correctly identify fault locations in an electrical power network, in order to rectify faults and restore power supply in the minimum possible time. Many automated fault location detection algorithms have been proposed, however, prior art requires topological and physical information of the electrical power network. This thesis presents a new method of detecting fault locations, in transmission as …

Real-Time Fault Detection And Reconfiguration Of A Three-Phase Electric Motor Drive, Danyal Mohammadi

Boise State University Theses and Dissertations

Variable-frequency drives (VFDs) are widely used for control of electrical machines such as induction motors (IMs) or permanent-magnet synchronous motors (PMSMs). Similar to other electrical devices, these drives are subject to failure. Several types of faults are associated with VFDs. For instance, faults such as an open-switch fault, a short-circuit switch fault are the two common faults in VFDs. These faults can yield catastrophic consequences if proper remedial action is not taken.

A unique remedial topology for the post-fault period and a new pulse width modulation (PWM) strategy are proposed so that not only the motor drive can continue the …

Feasibility Study Of Direct Application Of Two Deep And Dry Geothermal Wells For Heating The Buildings Of Moeil Village, Razieh Pourdarbani, Massomeh Alibaba, Mohsen Taghaddosi

Emirates Journal for Engineering Research

No abstract provided.

Ent1201 Introduction To Electricity For Live Entertainment Syllabus, Miguel A. Valderrama

Open Educational Resources

No abstract provided.

Optimal Power Flow Control Of Networked Dc Microgrids, Eddy H. Trinklein

Dissertations, Master's Theses and Master's Reports

The US military is moving toward the electrification of many weapon systems and platforms. Advanced weapon systems such as high energy radar, electro-magnetic kinetic weapons and directed energy pose significant integration challenges due to their pulsed power electrical load profile. Additionally, the weapons platforms, including ships, aircraft, and vehicles can be studied as a mobile microgrids with multiple generation sources, loads, and energy storage. There is also a desire to extend the mission profile and capabilities of these systems. Common goals are to increase fuel efficiency, maintaining system stability, and reduce energy storage size as typically required to enable pulsed …

Autonomous Combat Robot, Andrew J. Szabo Ii, Chris Heldman, Tristin Weber, Tanya Tebcherani, Holden Leblanc, Fabian Ardeljan

Williams Honors College, Honors Research Projects

This honors project will also serve as an engineering senior design project.

The objective is to design and build the software and electrical systems for a 60 lb weight class combat robot that will function autonomously and outperform manually driven robots during competition.

While running autonomously, the robot will use LiDAR sensors to detect and attack opponent robots. This robot will also be able to be remote controlled in manual mode. This will mitigate the risk in case the autonomy or sensors fail. LED lights on the robot will indicate whether it is in autonomous or manual mode. The system …

Series Compensation To Increase Power Flow: A Case Study On The Irish Transmission System, Aidan Heffernan, Jane Courtney

Conference papers

Ireland presents an interesting case study for transmission network strengthening. The majority of load in the country is located at the nation's capital, Dublin, in the East, while most of the new conventional generation and renewable generation are found in the South-West. Power is transferred between the two via a 400 kV network. This leads to large cross- country power flows. This power distribution disparity is due to increase. A large thermal generating station which is connected to the 400 kV system in the West, will close by 2025. This generation will be replaced partially with wind generation in the …