Electrical and Electronics Commons^™

Enhanced Security Utilizing Side Channel Data Analysis, Michael Taylor

Computer Science and Engineering Theses and Dissertations

The physical state of a system is affected by the activities and processes in which it is tasked with carrying out. In the past there have been many instances where such physical changes have been exploited by bad actors in order to gain insight into the operational state and even the data being held on a system. This method of side channel exploitation is very often effective due to the relative difficulty of obfuscating activity on a physical level. However, in order to take advantage of side channel data streams one must have a detailed working knowledge of how a …

Autonomous Control And Signal Acquisition System, Rion Cadell Krampe

Honors College Theses

Our goal is to continue a previous teams project to build a NDE autonomous control and signal acquisition system that is more precise, more customizable with both code and mechanical parts, and cheaper than a similar system bought by the school. This goal has two stages to it. First, to repair the system from considerable damage it received during transportation. Secondly, to continue designing and developing the system to make considerable progress towards the goal of a fully functional NDE system. Along with making progress we must consider the team after us and create an easy stepping off point for …

Machine Learning For Unmanned Aerial System (Uas) Networking, Jian Wang

Doctoral Dissertations and Master's Theses

Fueled by the advancement of 5G new radio (5G NR), rapid development has occurred in many fields. Compared with the conventional approaches, beamforming and network slicing enable 5G NR to have ten times decrease in latency, connection density, and experienced throughput than 4G long term evolution (4G LTE). These advantages pave the way for the evolution of Cyber-physical Systems (CPS) on a large scale. The reduction of consumption, the advancement of control engineering, and the simplification of Unmanned Aircraft System (UAS) enable the UAS networking deployment on a large scale to become feasible. The UAS networking can finish multiple complex …

Augmented Communications : A Solution For Overcoming High Spatial Correlation Of The Massive-Miso Vlc Channel, Monette Khadr

Legacy Theses & Dissertations (2009 - 2024)

A key challenge for future wireless networks is to come upon a riveting compromise between spectral efficiency, complexity, and energy efficiency. The challenge is also intensified due to the pace at which the Internet-of-Things (IoT) technology is arriving, causing an upheaval to pre-existing network infrastructures in terms of elevating spectrum scarcity. To keep pace with the exploding data demand forecasts, a circumvention is required. One realization is by utilizing the high-band spectrum and the rich body of knowledge on multiple-input multiple-output (MIMO) technologies. One of the prominent high frequency technologies is visible light communications (VLC). VLC provide a large unregulated …

Evaluating Deep-Learning Models For Debris-Covered Glacier Mapping, Zhiyuan Xie, Vijayan K. Asari, Umesh K. Haritashya

Electrical and Computer Engineering Faculty Publications

In recent decades, mountain glaciers have experienced the impact of climate change in the form of accelerated glacier retreat and other glacier-related hazards such as mass wasting and glacier lake outburst floods. Since there are wide-ranging societal consequences of glacier retreat and hazards, monitoring these glaciers as accurately and repeatedly as possible is important. However, the accurate glacier boundary, especially the debriscovered glacier (DCG) boundary, which is one of the primary inputs in many glacier analyses, remains a challenge even after many years of research using conventional remote sensing methods or machine-learning methods. The GlacierNet, a deep-learning-based approach, utilized the …

Collaborative Human-Machine Interfaces For Mobile Manipulators., Shamsudeen Olawale Abubakar

Electronic Theses and Dissertations

The use of mobile manipulators in service industries as both agents in physical Human Robot Interaction (pHRI) and for social interactions has been on the increase in recent times due to necessities like compensating for workforce shortages and enabling safer and more efficient operations amongst other reasons. Collaborative robots, or co-bots, are robots that are developed for use with human interaction through direct contact or close proximity in a shared space with the human users. The work presented in this dissertation focuses on the design, implementation and analysis of components for the next-generation collaborative human machine interfaces (CHMI) needed for …

Network Management, Optimization And Security With Machine Learning Applications In Wireless Networks, Mariam Nabil

Theses and Dissertations

Wireless communication networks are emerging fast with a lot of challenges and ambitions. Requirements that are expected to be delivered by modern wireless networks are complex, multi-dimensional, and sometimes contradicting. In this thesis, we investigate several types of emerging wireless networks and tackle some challenges of these various networks. We focus on three main challenges. Those are Resource Optimization, Network Management, and Cyber Security. We present multiple views of these three aspects and propose solutions to probable scenarios. The first challenge (Resource Optimization) is studied in Wireless Powered Communication Networks (WPCNs). WPCNs are considered a very promising approach towards sustainable, …

Resampling And Super-Resolution Of Hexagonally Sampled Images Using Deep Learning, Dylan Flaute, Russell C. Hardie, Hamed Elwarfalli

Electrical and Computer Engineering Faculty Publications

Super-resolution (SR) aims to increase the resolution of imagery. Applications include security, medical imaging, and object recognition. We propose a deep learning-based SR system that takes a hexagonally sampled low-resolution image as an input and generates a rectangularly sampled SR image as an output. For training and testing, we use a realistic observation model that includes optical degradation from diffraction and sensor degradation from detector integration. Our SR approach first uses non-uniform interpolation to partially upsample the observed hexagonal imagery and convert it to a rectangular grid. We then leverage a state-of-the-art convolutional neural network (CNN) architecture designed for SR …

A Unified Framework Of Deep Learning-Based Facial Expression Recognition System For Diversified Applications, Sanoar Hossain, Saiyed Umer, Vijayan K. Asari, Ranjeet Kumar Rout

Electrical and Computer Engineering Faculty Publications

This work proposes a facial expression recognition system for a diversified field of appli- cations. The purpose of the proposed system is to predict the type of expressions in a human face region. The implementation of the proposed method is fragmented into three components. In the first component, from the given input image, a tree-structured part model has been applied that predicts some landmark points on the input image to detect facial regions. The detected face region was normalized to its fixed size and then down-sampled to its varying sizes such that the advantages, due to the effect of multi-resolution …

Machine Learning For Analog/Mixed-Signal Integrated Circuit Design Automation, Weidong Cao

McKelvey School of Engineering Theses & Dissertations

Analog/mixed-signal (AMS) integrated circuits (ICs) play an essential role in electronic systems by processing analog signals and performing data conversion to bridge the analog physical world and our digital information world.Their ubiquitousness powers diverse applications ranging from smart devices and autonomous cars to crucial infrastructures. Despite such critical importance, conventional design strategies of AMS circuits still follow an expensive and time-consuming manual process and are unable to meet the exponentially-growing productivity demands from industry and satisfy the rapidly-changing design specifications from many emerging applications. Design automation of AMS IC is thus the key to tackling these challenges and has been …

Comparison Of Concrete And Steel Jacket Methods For Reinforcing A Concrete Bridge Pier By Numerical And Experimental Studies, Hadi Faghihmaleki

Makara Journal of Technology

Various rehabilitation and strengthening procedures have been developed in recent decades. A study to determine which methods can be implemented to increase the useful life of the bridge before strengthening must be performed. In this study, the seismic behavior of a reinforced concrete bridge pier with dimension 3.5 × 3.5 m, which was reinforced by two steel and a concrete jacket, was investigated. Nonlinear geometric models and materials were analyzed to estimate the seismic parameters of the pier. Results show an increase in energy absorption, ultimate strength, and ductility for the steel jacket, as well as a greater increase in …

Trend Significance Levels Of Rain Onset And Cessation And Lengths Of The Wet And Dry Seasons In Epe, Lagos State, Nigeria, Adekunle Adedeji Alli, Olorunwa Eric Omofunmi

Makara Journal of Technology

This study aims to reduce crop failure resulting from a dry spell, which is the first occurrence of unsustainable rainfall that deceives farmers into planting. Thus, trends need to be tested using hypothesis, kurtosis, and other statistics to analyze the risks associated with unstable planting calendars and their possible mitigation strategies. The daily rainfall data from 1982 to 2018 were obtained from the archive of NASA/POWER SRB/FLASH, and the research location is Epe, Lagos State, Nigeria, which lies at latitude 6.585° N and longitude 3.962° E. Microsoft Excel was used to perform the tests. Results show that the null hypothesis …

Improvement Of Electrical Properties Of Cmc-Pva Doped With Various Contents Of Lino3 As An Application For Hybrid Polymer Electrolytes, Amalia Zulkifli, Norfatihah Mazuki, Ahmad Salihin Samsudin

Makara Journal of Technology

The present work was carried out with the development of hybrid polymer electrolytes (HPEs) by using carboxymethyl cellulose (CMC)–polyvinyl alcohol (PVA) doped with different contents of lithium nitrate (LiNO3) for the determination of their structural and conduction properties. The structural analysis was conducted by using Fourier transform infra-red spectroscopy and showed the interaction between the blend host polymer and ionic dopant, which formed via the coordinating site of CMC-PVA and Li+-NO3−. The complexes of CMC-PVA doped LiNO3 led to an increment in ionic conductivity, as observed by electrical impedance spectroscopy, and the sample containing 20 wt% LiNO3 obtained the highest …

Predictive Delivery Man Assignment Problem Using Deep Learning, Rahmadini Payla Juarsa, Taufik Djatna

Makara Journal of Technology

Dispatching is a critical part in current online shopping. It relates to how the delivery man assignment should minimize cost along with the service from a source to an end customer with an appropriate scheduled time. The problem arises as neither enough products to deliver nor delivery men are available for dispatch, resulting in suboptimal service and a waste of money. The study aimed to formulate the cost of restaurant dispatching for inducing a deep learning-based solution with the gated recurrent unit recurrent neural network to receive hourly order data and to engage the result for near feature delivery man …

Kinetic Modeling Study Of Laminar Burning Velocity Of Gasoline–Ethanol–Methanol Blends At Elevated Temperature And Pressure, Ahmad Syihan Auzani, Cahyo Setyo Wibowo, Riesta Anggarani, Yulianto Sulistyo Nugroho, Bambang Sugiarto

Makara Journal of Technology

Gasoline–ethanol–methanol (GEM) blends have been considered to replace pure gasoline as spark ignition engine fuel. Their physical and chemical properties and performance and emission measurements from real engines have been reported previously. However, a fundamental study that can explain the unique results of GEM compared with those of pure gasoline is lacking. This study aims to compare the laminar burning velocity of GEM blends at different mixtures, equivalence ratios, temperatures, and pressures with that of pure gasoline. A laminar flame propagation model and reaction mechanisms from the literature were were for a numerical simulation. In this study, the chemical components …

Effect Of Arc Plasma Sintering On The Structural And Microstructural Properties Of Fe-Cr-Ni Austenitic Stainless Steels, Parikin Parikin, M. Dani, A. Dimyati, N. D. Purnamasari, B. Sugeng, M. Panitra, A. Insani, T. H. Priyanto, S. Mustofa, Syahbuddin Syahbuddin, A. Huang

Makara Journal of Technology

X-ray diffraction techniques were performed to determine the actual crystal structure of A2 austenitic stainless steel (ASS) as-cast and A2 ASS after arc plasma sintering (APS) for 2 s. Computations were conducted on the basis of the Bragg arithmetic formula by comparing the S2 arithmetic with the interplanar spacing. The Bragg arithmetic formula is a simple series for the determination of the crystalline phase of materials based on the Miller indices of cubic shapes or other shapes. A2 ASS as-cast was identified to have a crystal structure of face-centered cubic with lattice parameter a = 3.58 Å. A similar crystal …

Music Information Retrieval Based On Active Frequency, Hardianto Wibowo, Wildan Suharso, Yufis Azhar, Galih Wasis Wicaksono, Agus Eko Minarno, Dani Harmanto

Makara Journal of Technology

Music is the art of combining frequencies. A balance of frequencies gives rise to a harmonious tone. Several features of music can be analyzed, and they include sociocultural background, lyrics, mood, tempo, rhythm, harmony, melody, timbre, and instrumentation. In this study, we use the frequency of instrumentation as a feature for classification because each instrument has a frequency range. To test this frequency range, we use five music genres and one music playing skill. The five genres are dangdut, electronic dance music (EDM), metal, pop/rock, and reggae. The music playing skill is acoustic. Active frequencies are tested using the k-nearest …

Hardware For Quantized Mixed-Precision Deep Neural Networks, Andres Rios

Open Access Theses & Dissertations

Recently, there has been a push to perform deep learning (DL) computations on the edge rather than the cloud due to latency, network connectivity, energy consumption, and privacy issues. However, state-of-the-art deep neural networks (DNNs) require vast amounts of computational power, data, and energyâ??resources that are limited on edge devices. This limitation has brought the need to design domain-specific architectures (DSAs) that implement DL-specific hardware optimizations. Traditionally DNNs have run on 32-bit floating-point numbers; however, a body of research has shown that DNNs are surprisingly robust and do not require all 32 bits. Instead, using quantization, networks can run on …

Scalable Cognitive Radio Network Testbed In Real Time, Kevin Z. Yu

Master's Theses

Modern society places an increasingly high demand on data transmission. Much of that data transmission takes place through communication over the frequency spectrum. The channels on the spectrum are limited resources. Researchers realize that at certain times of day some channels are overloaded, while others are not being fully utilized. A spectrum management system may be beneficial to remedy this efficiency issue. One of the proposed systems, Cognitive Radio Network (CRN), has progressed over the years thanks to studies on a wide range of subjects, including geolocation, data throughput rate, and channel handoff selection algorithm, which provide fundamental support for …

Bibliometric Review On Iot Based System For Remote Downloading On Microcontroller, Arundhati Bandopadhyaya Ms., Diya Dodwad Ms., Diviyanshi Gupta Ms., Surya Koyyana Mr., Parag Narkhede Mr., Shripad Deshpande Mr.

Library Philosophy and Practice (e-journal)

Working with sensors has become an area of expertise within the domain of electronic engineering. On a day to day basis, thousands of sensors are put to use around us, for instance, in smoke alarms, speedometers, motors, computers, radiators etc. to accumulate sensor data, cables that connect the sensors to the bottom station after which the information is worked on. But cabling is often expensive especially when handling large scale industrial applications ^[5]. For an equivalent reason, low-cost wireless networks came into the picture recently and are in high demand. A research paper we found during our review of …

Intelligent And Secure Fog-Aided Internet Of Drones, Jingjing Yao

Dissertations

Internet of drones (IoD), which utilize drones as Internet of Things (IoT) devices, deploys several drones in the air to collect ground information and send them to the IoD gateway for further processing. Computing tasks are usually offloaded to the cloud data center for intensive processing. However, many IoD applications require real-time processing and event response (e.g., disaster response and virtual reality applications). Hence, data processing by the remote cloud may not satisfy the strict latency requirement. Fog computing attaches fog nodes, which are equipped with computing, storage and networking resources, to IoD gateways to assume a substantial amount of …

Bibliometric Analysis On Dynamic Target Tracking By Mobile Robot, Gaurav Atha Mr., Siddhant Chaturvedi Mr., Atishraj Desai Mr., Dhrumil Desai Mr., Shripad V. Deshpande Mr.

Library Philosophy and Practice (e-journal)

The survey and bibliometric research on dynamic target tracking by a mobile robot are discussed in this paper. The primary goal of this bibliometric analysis is to comprehend and analyze the scope of the literature in the field of mobile robots for obstacle avoidance, path planning and target tracking using Robot Operating System (ROS). The ROS contains various tools for data analysis, incorporates multiple robots and their sensors, and supports devices interaction for target seeking and localization in mobile robots. This detailed review was performed on various research publications about the mapping of the unknown field/environment by the ROS based …

Smart E-Bike Conversion Kit And Helmet, Megan West, Marena Trujillo, Hossein Asghari

Honors Thesis

With many state governments across the United States implementing shutdowns to prevent the spread of COVID-19, many bike retailers have seen dramatic increases in bike sales. Electric bicycles (e-bikes) have become increasingly popular as the public searches for alternatives to public transportation. Unfortunately, e-bike users assume some risk by riding bikes that are faster than conventional bicycles. While kits to convert conventional bicycles to e-bikes exist, no “smart” e-bike/helmet kit specifically designed to keep the user safe is currently available on the market. To mitigate risks, a smart e-bike conversion kit with multiple novel safety features, including auditory and visual …

Automated Bottling Station - Packaging System, Lauren Nicole Zinzilieta

Honors College Theses

This report focuses on the packaging system used at the end of the FESTO bottling station that is located in EP 2355. The system will be made up of an x-y 300 mm x 300 mm gantry system, an Arduino, two micro-stepping stepper drivers, and two 152.4 mm (6 in) single acting cylinders with a 3D printed bracket attached to both. The gantry system will be located at the end of the conveyor belt and will be programmed to pick up three bottles at a time and then will move a specified number of steps in both the x and …

Project Blipper, Peter Jacobs, Preston Delaware, Ryan Foster

Senior Design Project For Engineers

This project was sponsored by Clorox to design and create an automatic bottle-unscrambling system for possible implementation at their bottling plant in Chile. The objective was to use a robotic arm to unscramble bottles from an incoming conveyor belt and place them upright on an outbound conveyor belt. Throughout the research, design, and testing of solutions for this project, several design alternatives were found for each discipline, and will be presented to Clorox so that they can make an informed decision for how and if they want to move forward with implementation of this project.

The project was split into …

Side Channel Attack Counter Measure Using A Moving Target Architecture, Jithin Joseph

Electrical and Computer Engineering ETDs

A novel countermeasure to side-channel power analysis attacks called Side-channel Power analysis Resistance for Encryption Algorithms using DPR or SPREAD is investigated in this thesis. The countermeasure leverages a strategy that is best characterized as a moving target architecture. Modern field programmable gate arrays (FPGA) architectures provide support for dynamic partial reconfiguration (DPR), a feature that allows real-time reconfiguration of the programmable logic (PL). The moving target architecture proposed in this work leverages DPR to implement a power analysis countermeasure to side-channel attacks, the most common of which are referred to as differential power analysis (DPA) and correlation power analysis …

Addressing Security Challenges In Embedded Systems And Multi-Tenant Fpgas, Georgios Provelengios

Doctoral Dissertations

Embedded systems and field-programmable gate arrays (FPGAs) have become crucial parts of the infrastructure that supports our modern technological world. Given the multitude of threats that are present, the need for secure computing systems is undeniably greater than ever. Embedded systems and FPGAs are governed by characteristics that create unique security challenges and vulnerabilities. Despite their array of uses, embedded systems are often built with modest microprocessors that do not support the conventional security solutions used by workstations, such as virus scanners. In the first part of this dissertation, a microprocessor defense mechanism that uses a hardware monitor to protect …

Numerical Study Of A Buckling Restrained Brace (Brb) In Steel Structures And Comparison With A Convergent Ordinary Brace (Ocb) Under Static And Dynamic Loading, Fatemeh Habibpour

Makara Journal of Technology

Bulk metallic glass (BMG) has good mechanical strength, high hardness, wear resistance, and corrosion resistance with promising application in various industries. However, for the industrial production of BMG, the main issue is how to overcome limitations of joining with other materials. The present study focuses on solder processing at low operating temperature to avoid exceeding the recrystallization temperature. A feasible joining process for BMG was developed using lead-free solders. The BMG surface is pre-plated with copper, nickel, or titanium as a wetting layer. The reaction temperature is set between the glass transition temperature of BMG and the melting point of …

Analysis Of The Interfacial Reaction Between Bulk Metallic Glass Coated Copper, Nickel, And Titanium With Lead-Free Solders, Andromeda Dwi Laksono, Yee-Wen Yen, Rifqi Aulia Tanjung, Teodoro A. Amatosa, Ruki Harwahyu

Makara Journal of Technology

Bulk metallic glass (BMG) has good mechanical strength, high hardness, wear resistance, and corrosion resistance with promising application in various industries. However, for the industrial production of BMG, the main issue is how to overcome limitations of joining with other materials. The present study focuses on solder processing at low operating temperature to avoid exceeding the recrystallization temperature. A feasible joining process for BMG was developed using lead-free solders. The BMG surface is pre-plated with copper, nickel, or titanium as a wetting layer. The reaction temperature is set between the glass transition temperature of BMG and the melting point of …

Design Of Ac Microgrid Topology With Photovoltaic Uncertainties In A Rural Village, Vannak Vai

Makara Journal of Technology

Energy needs are increasing day by day, especially for developing countries, due to population growth and changing lifestyles. A suitable microgrid topology with renewable energy integration is considered to fulfill the people and society’s needs. This paper focuses on the design of AC microgrid topology for a nonelectrified village with the integration of PV uncertainties in both sitting and sizing. The development of an optimal algorithm based on the conductor use minimization and unbalanced load improvement is proposed. The shortest path is proposed to search for the minimum conductor use. Then, the algorithm for improving the unbalanced load with two …