Controls and Control Theory Commons^™

Identification Of Hydrodynamic Forces Developed By Flapping Fins In A Watercraft Propulsion Flow Field, Erdem Aktosun

University of New Orleans Theses and Dissertations

In this work, the data analysis of oscillating flapping fins is conducted for mathematical model. Data points of heave and surge force obtained by the CFD (Computational Fluid Dynamics) for different geometrical kinds of flapping fins. The fin undergoes a combination of vertical and angular oscillatory motion, while travelling at constant forward speed. The surge thrust and heave lift are generated by the combined motion of the flapping fins, especially due to the carrier vehicle’s heave and pitch motion will be investigated to acquire system identification with CFD data available while the fin pitching motion is selected as a function …

Design Of A Haptic Interface For Medical Applications Using Magneto-Rheological Fluid Based Actuators, Nima Najmaei

Electronic Thesis and Dissertation Repository

This thesis reports on the design, construction, and evaluation of a prototype two degrees-of-freedom (DOF) haptic interface, which takes advantage of Magneto-Rheological Fluid (MRF) based clutches for actuation. Haptic information provides important cues in teleoperated systems and enables the user to feel the interaction with a remote or virtual environment during teleoperation. The two main objectives in designing a haptic interface are stability and transparency. Indeed, deficiencies in these factors in haptics-enabled telerobotic systems has the introduction of haptics in medical environments where safety and reliability are prime considerations. An actuator with poor dynamics, high inertia, large size, and heavy …

Design Of System Level Control For A Residential Power Router, Fahad Hossain

Graduate Theses and Dissertations

This thesis presents the overall power flow and load management system for a 2 kW residential power router. The objective is to satisfy the residential load demand with cost savings by managing the energy sources including PV, battery, generator, and grid. The power flow management system algorithm is developed both for grid-connected mode and island mode. This algorithm involves the battery state of charge estimation, available PV power, load demand and electricity grid pricing. The residential load management algorithm is also developed using PV power prediction and load power prediction acquired for a day.¬ A Labview GUI is also developed …

Development Of A Digital Controller For Motor Control Experiments In The Ee472 Lab, Jeffrey David D'Amelio

Master's Theses

A digital motor controller for student lab use is designed, built, and tested. The controller uses an encoder for position measurement, and an H-bridge to drive the electromechanical plant.

A user interface is created to enhance usability of the device. The user interface is able to display key parameters of the control algorithm as well as the state of the system. It is also used to modify the gains and sample rate of the control algorithm.

The design of the system is refined, and 10 units are built for the EE472 Digital Controls Lab. The lab manuals for the first …

A Dc Distribution System For Power System Integration Of Plug-In Electric Vehicles; Modeling, Stability And Operation, Mansour Tabari

Electronic Thesis and Dissertation Repository

This thesis is mainly focused on (i) modeling of dc distribution systems for power system integration of plug-in electric vehicles (PEVs), (ii) proposing a method to enhance the stability of the dc distribution systems, and (iii) proposing an energy management strategy to control the power flow in the dc distribution system. The dc distribution system is expected to be more efficient and economical than a system of ac-dc battery chargers directly interfaced with an ac grid.

In the first part, a systematic method for developing a model for a dc distribution system, based on the configuration of the system is …

Ubot-7: The Design Of A Compliant Dexterous Mobile Manipulator, Jonathan Cummings

Masters Theses

This thesis presents the design of uBot-7, the latest version of a dexterous mobile manipulator. This platform has been iteratively developed to realize a high performance-to-cost dexterous whole body manipulator with respect to mobile manipulation. The semi-anthropomorphic design of the uBot is a demonstrated and functional research platform for developing advanced autonomous perception, manipulation, and mobility tasks. The goal of this work is to improve the uBot’s ability to sense and interact with its environment in order to increase the platforms capability to operate dexterously, through the incorporation of joint torque feedback, and safely, through the implementation of passive and …

Interpreting, Stephanie Jo Kent

Doctoral Dissertations

What do community interpreting for the Deaf in western societies, conference interpreting for the European Parliament, and language brokering in international management have in common? Academic research and professional training have historically emphasized the linguistic and cognitive challenges of interpreting, neglecting or ignoring the social aspects that structure communication. All forms of interpreting are inherently social; they involve relationships among at least three people and two languages. The contexts explored here, American Sign Language/English interpreting and spoken language interpreting within the European Parliament, show that simultaneous interpreting involves attitudes, norms and values about intercultural communication that overemphasize information and discount …

Comprehensive Statcom Control For Distribution And Transmission System Applications, Shubham Gupta

Electronic Thesis and Dissertation Repository

This thesis presents the development of a comprehensive STATCOM controller for load compensation, voltage regulation and voltage balancing in electric power distribution and transmission networks. The behavior of this controller is first validated with published results. Subsequently, the performance of this STATCOM controller is examined in a realistic Hydro One distribution feeder for accomplishing the compensation of both mildly and grossly unbalanced loads, and balancing of network voltages using PSCAD/EMTDC software. The STATCOM voltage control function is utilized for increasing the connectivity of wind plants in the same distribution feeder. The thesis further presents a frequency scanning technique for simple …

A Cfd Assisted Control System Design For Supercritical Water Cooled Reactor, Rohit V. Maitri

Electronic Thesis and Dissertation Repository

In this study, the methodology to construct a control system based on computational fluid dynamics (CFD) simulations is developed for supercritical water cooled reactor (SCWR). The CFD model using Reynolds Stress Model (RSM) and k-w SST model is validated with the experimental cases of steady state and vertically up flowing supercritical water in circular tubes for normal heat transfer and deteriorated heat transfer (DHT) cases. This model is extended to simulate the transient thermal-hydraulic behaviour of supercritical fluid flow and heat transfer, and the results are also compared with the 1-D numerical model, THRUST. The DHT phenomenon is investigated using …

Automated Pet Food Dispenser, Kevin M. Shibley

Electrical Engineering

Electronics revolutionize the world and simplify life. The Automated Pet Food Dispenser (APFD) revolutionizes the pet industry and provides unprecedented food capacity and delivery capability, giving pet owners worry-free vacationing. Sensors and timers optimize functionality and reduce waste while improving reliability and usability. User-defined settings and customization gives the device adaptability to meet every customer’s needs.

Real Time Swim Instructor, Konrad Antoniuk

Electrical Engineering

Both competitive and recreational swimmers want an efficient swim stroke but often lack consistent feedback with technical insight. Competitive swimmers rely on coaches for instruction but have to stop swimming to listen. The Real Time Swim Instructor project provides live feedback to a swimmer so they can feel their stroke correction while they’re swimming. The developing swimmer feels the difference between correct and incorrect form instantaneously.

The project takes on the responsibility of measuring the moving body, accurately determining stroke improvement, functioning under water, and providing recognizable feedback. Additionally, the user can review their swim from data stored in memory. …

Automated Foosball Table, Jim R. Stefani, Alex J. Herpy, Brett Gordon Jaeger, Kevin S. Haydon, Derek Alan Hamel

Mechanical Engineering

This project is the second iteration of an automated foosball table for Yaskawa America as a trade show display. The table is meant to provide an interactive experience which highlights the speed and precision of the Yaskawa hardware. The first iteration of the project was mainly focused on creating the physical hardware for the system and to begin the basic programming for the system. This phase of the project was focused on finalizing the physical hardware of the system, implementing the vision system and to continue the basic programing of the system AI. A third team will be assigned to …

Variable Precision Tandem Analog-To-Digital Converter (Adc), Colton A. Parsons

Master's Theses

This paper describes an analog-to-digital signal converter which varies its precision as a function of input slew rate (maximum signal rate of change), in order to best follow the input in real time. It uses Flash and Successive Approximation (SAR) conversion techniques in sequence.

As part of the design, the concept of "total real-time optimization" is explored, where any delay at all is treated as an error (Error = Delay * Signal Slew Rate). This error metric is proposed for use in digital control systems. The ADC uses a 4-bit Flash converter in tandem with SAR logic that has variable …

Non-Linear Electromechanical System Dynamics, Shathiyakkumar Ganapathy Annadurai

University of New Orleans Theses and Dissertations

Electromechanical systems dynamics analysis is approached through nonlinear differential equations and further creating a state space model for the system. There are three modules analyzed and validated, first module consists two magnet coupled with a mass spring damper system as a band-pass system, Low-pass equivalent system and Low-pass equivalent system through perturbation analysis. Initially Band Pass frameworks for the systems are formulated considering the relation between the mechanical forcing and current. Using Mathematical tools such as Hilbert transforms, Low-Pass equivalent of the systems are derived. The state equations of the systems are then used to design a working model in …

Design And Development Of Magneto-Rheological Actuators With Application In Mobile Robotics, Wenjun Li

Electronic Thesis and Dissertation Repository

In recent years, Magneto-Rheological (MR) fluids devices are widely studied and used for various purposes. Among these MR fluids devices, the MR actuator has attracted increasing attention for last two decades. An MR actuator is usually made of an active component (motor) and MR clutches. Compared with the regular actuators, the MR actuator features compliance due to the existence of MR fluids, which is commonly consider as benefits at the aspect of safety. On the other hand, the MR actuator has advantages on controllable bandwidth, torque-mass and torque-inertia ratios compared with the other compliant actuators.

In this study, a new …

Modeling, Analysis, And Control Of A Mobile Robot For In Vivo Fluoroscopy Of Human Joints During Natural Movements, Matthew A. Young

Doctoral Dissertations

In this dissertation, the modeling, analysis and control of a multi-degree of freedom (mdof) robotic fluoroscope was investigated. A prototype robotic fluoroscope exists, and consists of a 3 dof mobile platform with two 2 dof Cartesian manipulators mounted symmetrically on opposite sides of the platform. One Cartesian manipulator positions the x-ray generator and the other Cartesian manipulator positions the x-ray imaging device. The robotic fluoroscope is used to x-ray skeletal joints of interest of human subjects performing natural movement activities. In order to collect the data, the Cartesian manipulators must keep the x-ray generation and imaging devices accurately aligned while …

Implementation Of Prediction Algorithms To Reduce Latency In Control Of Switching Converters, Brent Bell

Electrical Engineering Undergraduate Honors Theses

Using pulse-width modulation (PWM) to control switching converters such as a dual active bridge introduces latency into a system [1]. Latency in a switching converter decreases the effective bandwidth that the converter can be switched at and for the case of a closed loop control system decreases the effective closed loop system stability. This delay can be attributed to sampling of the control signal and calculation time for the PWM. If a prediction scheme is implemented in this calculation, the next switching time could be predicted to remove any latency. There are effectively two steps in order to achieve this …

Optimal Control Of Energy Efficient Buildings, Cale David Nelson

Masters Theses

The building sector consumes a large part of the energy used in the United States and is responsible for nearly 40% of greenhouse gas emissions. Therefore, it is economically and environmentally important to reduce the building energy consumption to realize massive energy savings. Commercial buildings are complex, multi-physics, and highly stochastic dynamic systems. Recent work has focused on integrating modern modeling, simulation, and control techniques to solving this challenging problem. The overall focus of this thesis is directed toward designing an energy efficient building by controlling room temperature. One approach is based on a distributed parameter model represented by a …

Modeling And Control Of Steerable Ablation Catheters, Mahta Khoshnam Tehrani

Electronic Thesis and Dissertation Repository

Catheters are long, flexible tubes that are extensively used in vascular and cardiac interventions, e.g., cardiac ablation, coronary angiography and mitral valve annuloplasty. Catheter-based cardiac ablation is a well-accepted treatment for atrial fibrillation, a common type of cardiac arrhythmia. During this procedure, a steerable ablation catheter is guided through the vasculature to the left atrium to correct the signal pathways inside the heart and restore normal heart rhythm. The outcome of the ablation procedure depends mainly on the correct positioning of the catheter tip at the target location inside the heart and also on maintaining a consistent contact between the …

An Adaptive Kalman Filter For Voltage Sag Detection In Power Systems, Hisham Odeh Alrawashdeh

Dissertations

The exact values of the noise covariance matrix of the Kalman filter state vector Q and the measured signal noise covariance matrix R must be obtained in order to achieve the optimal performance of the Kalman filter. There have been many techniques and assumptions made to evaluate and compute Q and R. The effects of Q and R are investigated in detail in this dissertation. Based on these investigations, the Kalman filter has been modeled to detect the fundamental signal amplitude variations of power system signals. This technique helps in evaluating voltage sags in power systems.

Two algorithms are …

Control Of Cooperative Haptics-Enabled Teleoperation Systems With Application To Minimally Invasive Surgery, Amir Takhmar

Electronic Thesis and Dissertation Repository

Robot-Assisted Minimally Invasive Surgical (RAMIS) systems frequently have a structure of cooperative teleoperator systems where multiple master-slave pairs are used to collaboratively execute a task. Although multiple studies indicate that haptic feedback improves the realism of tool-tissue interaction to the surgeon and leads to better performance for surgical procedures, current telesurgical systems typically do not provide force feedback, mainly because of the inherent stability issues. The research presented in this thesis is directed towards the development of control algorithms for force reflecting cooperative surgical teleoperator systems with improved stability and transparency characteristics. In the case of cooperative force reflecting teleoperation …

Implementación De Una Red De Sensores Inteligentes Mediante Comunicación Inalámbrica, Para Reducir El Consumo De Energía, Jorge Iván Patiño López, Oscar Javier Medellín Guzmán

Ingeniería en Automatización

Debido a la necesidad de desarrollar tecnología que aproveche energías alternativas y que puedan disminuir su consumo sin el detrimento de perder información, se realizó la implementación de una red inalámbrica de sensores inteligentes conformada por tres módulos finales y un coordinador conectado a un sistema supervisorio para almacenamiento de datos. La característica principal de esta red consiste en dotar a los módulos finales de inteligencia artificial basada en lógica difusa para que les permita decidir cuándo enviar información al coordinador, de modo que no trabajen como un sistema temporizado; de acuerdo a las reglas establecidas en la inteligencia los …

Filtered-Dynamic-Inversion Control For Fixed-Wing Unmanned Aerial Systems, Jon Mullen

Theses and Dissertations--Mechanical Engineering

Instrumented umanned aerial vehicles represent a new way of measuring turbulence in the atmospheric boundary layer. However, autonomous measurements require control methods with disturbance-rejection and altitude command-following capabilities. Filtered dynamic inversion is a control method with desirable disturbance-rejection and command-following properties, and this controller requires limited model information. We implement filtered dynamic inversion as the pitch controller in an altitude-hold autopilot. We design and numerically simulate the continuous-time and discrete-time filtered-dynamic-inversion controllers with anti-windup on a nonlinear aircraft model. Finally, we present results from a flight experiment comparing the filtered-dynamic-inversion controller to a classical proportional-integral controller. The experimental results show …

Virtualized Welding Based Learning Of Human Welder Behaviors For Intelligent Robotic Welding, Yukang Liu

Theses and Dissertations--Electrical and Computer Engineering

Combining human welder (with intelligence and sensing versatility) and automated welding robots (with precision and consistency) can lead to next generation intelligent welding systems. In this dissertation intelligent welding robots are developed by process modeling / control method and learning the human welder behavior.

Weld penetration and 3D weld pool surface are first accurately controlled for an automated Gas Tungsten Arc Welding (GTAW) machine. Closed-form model predictive control (MPC) algorithm is derived for real-time welding applications. Skilled welder response to 3D weld pool surface by adjusting the welding current is then modeled using Adaptive Neuro-Fuzzy Inference System (ANFIS), and compared …

Multifrequency Averaging In Power Electronic Systems, Fei Pan

Theses and Dissertations--Electrical and Computer Engineering

Power electronic systems have been widely used in the electrical power processing for applications with power levels ranging from less than one watt in battery-operated portable devices to more than megawatts in the converters, inverters and rectifiers of the utility power systems. These systems typically involve the passive elements such as inductors, capacitors, and resistors, the switching electronic components such as IGBTs, MOSFETS, and diodes, and other electronic circuits. Multifrequency averaging is one of the widely used modeling and simulation techniques today for the analysis and design of power electronic systems. This technique is capable of providing the average behavior …

Model Analysis And Predictive Control Of Double Electrode Submerged Arc Welding Process For Fillet Joints With Root Opening, Yi Lu

Theses and Dissertations--Electrical and Computer Engineering

Submerged Arc Welding (SAW) for fillet joints is one of the major applications in the shipbuilding industry. Due to the requirement for the weld size, a sufficient amount of metal must be deposited. In conventional SAW process, the heat input is proportional to the amount of metal melted and is thus determined by the required weld size. To meet this requirement, an excessive amount of heat is applied causing large distortions on the welded structures whose follow-up straightening is highly costly. In order to reduce the needed heat input, Double-Electrode (DE) technology has been practiced creating the Double-Electrode SAW (DE-SAW) …

Multi-Domain, Multi-Objective-Optimization-Based Approach To The Design Of Controllers For Power Electronics, Jing Shang

Theses and Dissertations--Electrical and Computer Engineering

Power converter has played a very important role in modern electric power systems. The control of power converters is necessary to achieve high performance. In this study, a dc-dc buck converter is studied. The parameters of a notional proportional-integral controller are to be selected. Genetic algorithms (GAs), which have been widely used to solve multi-objective optimization problems, is used in order to locate appropriate controller design. The control metrics are specified as phase margin in frequency domain and voltage error in time-domain. GAs presented the optimal tradeoffs between these two objectives. Three candidate control designs are studied in simulation and …

Measurement And Modeling Of Humidity Sensors, Jingbo Tong

Theses and Dissertations--Electrical and Computer Engineering

Humidity measurement has been increasingly important in many industries and process control applications. This thesis research focus mainly on humidity sensor calibration and characterization. The humidity sensor instrumentation is briefly described. The testing infrastructure was designed for sensor data acquisition, in order to compensate the humidity sensor’s temperature coefficient, temperature chambers using Peltier elements are used to achieve easy-controllable stable temperatures. The sensor characterization falls into a multivariate interpolation problem. Neuron networks is tried for non-linear data fitting, but in the circumstance of limited training data, an innovative algorithm was developed to utilize shape preserving polynomials in multiple planes in …

Neuromodulation Based Control Of Autonomous Robots On A Cloud Computing Platform, Cameron Muhammad

Electronic Theses and Dissertations

In recent years, the advancement of neurobiologically plausible models and computer networking has resulted in new ways of implementing control systems on robotic platforms. The work presents a control approach based on vertebrate neuromodulation and its implementation on autonomous robots in the open-source, open-access environment of robot operating system (ROS). A spiking neural network (SNN) is used to model the neuromodulatory function for generating context based behavioral responses of the robots to sensory input signals. The neural network incorporates three types of neurons- cholinergic and noradrenergic (ACh/NE) neurons for attention focusing and action selection, dopaminergic (DA) neurons for rewards- and …

Development Of An Optical Sensor For Real-Time Weed Detection Using Laser Based Spectroscopy, Arie Jacobus Paap

Theses: Doctorates and Masters

The management of weeds in agriculture is a time consuming and expensive activity, including in Australia where the predominant strategy is blanket spraying of herbicides. This approach wastes herbicide by applying it in areas where there are no weeds. Discrimination of different plant species can be performed based on the spectral reflectance of the leaves. This thesis describes the development of a sensor for automatic spot spraying of weeds within crop rows. The sensor records the relative intensity of reflected light in three narrow wavebands using lasers as an illumination source.

A prototype weed sensor which had been previously developed …